1995 LAND ROVER DISCOVERY petrol

ZF
17
REPAIR PARKING PAWL MECHANISM
Service repair no - 44.28.07
Remove
1.Remove transfer box.
See TRANSFER
GEARBOX, Repair, LT230T Transfer Gearbox
2.Remove transfer gear selector housing.
3.Loosen nine bolts holding extension housing.
4.Remove extension housing ensuring that seal is
not damaged, discard gasket.
5.Remove extension shaft and retaining bolt with
'O' ring. If Tdi vehicle, remove spacer.
6.Remove governor assembly with parking wheel.
7.Remove guide plate bolt.
8.Remove plate and guide plate from gearbox
case.
9.Remove pin, pawl and spring.
CAUTION: When removing assembly.
Avoid damaging parts which could weaken
spring tension.
10.Inspect all parts for wear or damage. Replace if
necessary.
Refit
11.Fit pin and leg spring, locate spring correctly.
12.Fit pawl to pin. Locate spring leg into hole in
pawl to create tension in spring.
13.Fit plate and guide plate. Tighten to
10 Nm.
14.Push governor assembly with parking wheel
onto output shaft until seated.
NOTE: Apply petroleum jelly to 'O' ring.
Ensure seal rings are snapped together
and seated.
15.Fit new gasket to rear of gearbox. Fit extension
housing, taking care not to damage seal or
assembly.
16.Fit extension shaft with spacer if Tdi and
retaining bolt with new 'O' ring.
17.Fit extension housing, tighten nine bolts to
23Nm.
18.Fit transfer gear selector housing, tighten three
bolts to
25 Nm.
19.Refit transfer box.

ZF
19
REPAIR 6.Screw in two bolts, diagonally opposite each
other. Tap lightly using a soft headed mallet to
remove pump assembly from intermediate plate.
7.Remove shaft sealing ring and 'O' ring from
pump housing and discard.
8.Using oil seal replacer LST108 fit shaft seal ring
into pump housing.
9.Fit 'O' ring onto circumference of pump housing.
10.Align dowel with hole in intermediate plate and
press pump housing home.11.Fit pump housing to intermediate plate, tighten
eight bolts to
10 Nm.
12.Place bell housing and intermediate plate
assembly on bench, front face up. Using oil
pump rotation sleeve LST111, check that pump
gears rotate freely.
13.Before fitting intermediate plate and bell housing
assembly,check that thrust washer and axial
cage are seated on A clutch housing.
14.Place gasket and disc washer onto bell housing
and intermediate plate assembly using
Petroleum Jelly.
15.Fit bell housing and intermediate plate assembly
to gearcase. Tighten twelve bolts to
46 Nm.
16.Place end float gauge LST111 onto pump
housing and check that axial play is between
0.2-0.4 mm. Replace existing washer, situated at
rear of intermediate plate, with a suitable washer
to give required end float.
17.Refit torque converter into housing using torque
converter handles 18G1501, checking that
dimension from converter fixing bolt boss to
converter housing face is 50 mm. This shows
converter is properly seated in housing.
18.Refit gearbox/transfer box assembly.
See
LT230T Transfer Gearbox

44AUTOMATIC GEARBOX
20
REPAIR ELIMINATING LEAKS BETWEEN GEARBOX
HOUSING AND INTERMEDIATE PLATE
1.Remove gearbox and transfer box assembly.
See LT230T Transfer Gearbox
2.Place gearbox on bench. Remove torque
converter using torque converter handles
18G1501, taking care not to damage torque
converter/oil pump housing oil seal.
3.Remove twelve hexagonal bolts (inner ring
pattern).
4.Remove bell housing/intermediate plate
assembly from gearbox case and discard
gasket.
5.Place new gasket onto intermediate plate using
Petroleum Jelly.
6.Before fitting bell housing assembly check that
thrust washer and axial cage are seated on A
clutch housing.
7.Fit bell housing assembly with disc washer to
gearcase. Tighten twelve bolts to
46Nm.
8.Place end-float gauge LST111 onto pump
housing and check that axial play is between
0.2-0.4 mm. Replace existing washer, situated at
rear of intermediate plate, with a suitable washer
to give required end-float.
9.Refit torque converter using torque converter
handles 18G1501. Checking that dimension
from converter fixing boss to converter housing
case is 50mm. This dimension shows converter
is properly seated.
10.Refit gearbox/transfer box assembly.
See
LT230T Transfer Gearbox

ZF
21
REPAIR REPLACING PUMP
Service repair no - 44.32.01
1.Remove gearbox and transfer box assembly.
See LT230T Transfer Gearbox
2.Place gearbox on bench. Remove torque
converter using torque converter handles
18G1501, taking care not to damage torque
converter/oil pump housing oil seal.
3.Remove twelve bolts (inner ring pattern).
4.Remove bell housing and pump assembly from
gearbox case, discard gasket.
5.Remove eight bolts on rear of pump.
6.Screw in two bolts,diagonally opposite each
other, tap lightly using a soft headed mallet to
free pump assembly from intermediate plate.
7.Fit new pump assembly, aligning dowel with hole
in intermediate plate, press pump housing home.
8.Secure pump housing to intermediate plate
using eight hexagonal bolts. Tighten to
10 Nm.
9.Place bell housing and intermediate plate
assembly on bench, front face up. Using oil
pump rotation sleeve LST111, check that pump
gears rotate freely.
10.Before replacing intermediate plate/bell housing
assembly check that thrust washer and axial
cage are seated on A clutch housing.
11.Place new gasket and disc washer onto bell
housing and intermediate plate assembly using
a Petroleum Jelly.
12.Fit bell housing and intermediate plate assembly,
tighten twelve bolts to
46 Nm.

STEERING
5
OVERHAUL Rack thrust pad and adjuster
43.Examine thrust pad for scores.
44.Examine adjuster for wear in pad seat.
45.Fit new sealing ring to rack adjuster.
Rack and piston
46.Examine for excessive wear on rack teeth.
47.Ensure thrust pad bearing surface is free from
scores and wear.
48.Ensure piston outer diameters are free from
burrs and damage.
49.Examine seal and ring groove for scores and
damage.
50.Fit new ring to piston. Warm nylon seal and fit to
piston.
51.Slide piston assembly into cylinder with rack
tube outwards.Reassemble
NOTE: When fitting replacement oil seals
lubricate with recommended fluid and
ensure absolute cleanliness.
Sector shaft oil seal
52.Fit oil seal, lip side first.
53.Fit extrusion washer.
54.Fit dust seal, lipped side last.
55.Fit circlip.
Fitting valve and worm assembly
56.Refit original shims and inner bearing cup. Use
Petroleum Jelly to aid assembly.
NOTE: If original shims are not used, fit
shims of 0.76 mm thickness.
57.Fit inner cage and bearings assembly.
58.Fit valve and worm assembly.
59.Fit outer cage and bearings assembly.
60.Fit outer bearing cup.

BRAKES
9
DESCRIPTION AND OPERATION Petrol engine vacuum system
The vacuum necessary to operate the brake servo on
petrol engine vehicles is provided by the engine inlet
manifold. During normal operation of the brakes only a
small volume of air is drawn from the servo and into
the inlet manifold or plenum chamber. However any
excessive air leaks due to damage in the brake servo
system or manifold hose connection, will effect the
mixture strength and ECM fuelling calculations on
engines equipped with an MFI system.
Diesel engine vacuum system
As the diesel engine inlet system does not produce
depression sufficient to operate the brake servo, it is
necessary to install an engine driven vacuum pump.
During normal operation of the brakes only a small
volume of air is drawn from the servo by the vacuum
pump. However as the pump exhausts air into the
engine crankcase atmosphere, an air leak due to
damage in the brake servo system or pump hose
connection, may cause excessive crankcase
pressure.

BRAKES
1
REPAIR GENERAL BRAKE SERVICE PRACTICE
Brake fluid precautions
WARNING: Do not allow brake fluid to
come into contact with eyes or skin.
CAUTION: Brake fluid can damage
paintwork, if spilled wash off immediately
with plenty of clean water.
CAUTION: Use only correct grade of brake
fluid. If an assembly fluid is required use
ONLY brake fluid. Do NOT use mineral oil,
i.e. engine oil etc.
CAUTION: Thoroughly clean all brake
calipers, pipes and fittings before
commencing work on any part of the brake
system. Failure to do so could cause foreign
matter to enter the system and cause damage to
seals and pistons which will seriously impair the
efficiency of the brake system.
·To ensure the brake system efficiency is not
impaired the following warnings must be
adhered to :-
·DO NOT use any petroleum based cleaning
fluids or any proprietary fluids containing
petrol.
·DO NOT use brake fluid previously bled from
the system.
·DO NOT flush the brake system with any fluid
other than the recommended brake fluid.
The brake system should be drained and flushed
at the recommended service intervals.
Cover all electrical terminals carefully to make
absolutely certain that no fluid enters the
terminals and plugs.FLUID LEVEL CHECK / TOP UP
WARNING: Clean reservoir body and filler
cap before removing cap. Use only fluid
from a sealed container.
1.Park vehicle on level ground.
2.Check level is between 'MIN' and 'MAX' marks.
3.If level is below 'MIN' mark top up fluid level to
'MAX' mark on reservoir, using correct fluid.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids
Do not fill reservoir above maximum line

80HEATING AND VENTILATION
4
REPAIR WATER VALVE
Service repair no - 80.10.16
Remove
1.Disconnect vacuum pipe from water valve.
2.Slacken 4 clips securing hoses to water valve.
3.Use a thin blade to break seal between hoses
and nozzles
4.Disconnect heater inlet hose from valve.
NOTE: A quantity of coolant will be
released.
5.Disconnect heater outlet hose from valve.
6.Lever valve from coolant pipe hoses.
Refit
7.Reverse removal procedure. Lightly lubricate
water valve nozzles with petroleum jelly.
8.Reverse removal procedure. Top-up engine
coolantVACUUM SWITCH - WATER VALVE
Service repair no - 80.10.36
Remove
1.Release emission pipe from retaining clip.
2.Remove bolt securing switch to bulkhead.
3.Disconnect multiplug from switch.
4.Disconnect 2 vacuum pipes and remove vacuum
switch.
Refit
5.Reverse removal procedure.