1995 LAND ROVER DISCOVERY gearbox

10MAINTENANCE
2
MAINTENANCE
CHECK SECURITY AND OPERATION OF PARK
BRAKE
Parking brake adjust
1.Select a gear or 'P' in main gearbox.
2.Chock road wheels.
3.Release parkbrake lever.
4.Remove switch panel from centre console.
5.Underneath vehicle, rotate brake adjuster
clockwise until brake shoes are fully expanded
against drum.
6.Back off adjuster until drum is free to rotate.
7.Rotate adjustment thumbwheel below parkbrake
lever until parking brake is fully operational on
third notch of ratchet.
NOTE: Cable adjustment must ONLY be
used for initial setting and to compensate
for cable stretch. It MUST NOT be used to
take up brake shoe wear, which MUST be adjusted
at brake drum.
8.Operate parking brake to settle shoes. Recheck
parkbrake is fully operational on third notch of
ratchet. Readjust if necessary.
9.Refit switch panel.

10MAINTENANCE
12
MAINTENANCE
EXTERNALLY CHECK INTERCOOLER FOR
OBSTRUCTION - Tdi
Clear any trapped dirt or flies from vanes of
intercooler
CLEAN INTERCOOLER ELEMENT - Tdi
Remove
1.Remove intercooler element.
2.Flush intercooler with ICI 'GENKLENE'or
à oD-SOLVE' propriety cleaner, following the
manufacturer's instructions.
3.Dry the intercooler completely ensuring that no
liquid remains in the element.
Refit
4.Refit intercooler element.UNDER VEHICLE MAINTENANCE
Vehicles operating under severe conditions of dust,
sand, mud and water should have oils changed and
lubrication carried out at more frequent intervals than
is recommended in maintenance schedules.
RENEW ENGINE OIL AND FILTER - Tdi
CAUTION: Serious damage to the
turbocharger will result if engine is run
above idling speed before oil pressure is
restored.
RENEW ENGINE OIL - V8i
RENEW ENGINE OIL AND FILTER - V8i
CAUTION: To prevent an airlock occuring
after removing filter, fill new filter with oil
and fit immediately after removing old
filter. If airlock does occur fill oil pump with
petroleum jelly.
RENEW ENGINE OIL AND FILTER - Mpi
CHECK/TOP UP MANUAL GEARBOX OIL - V8i
1.Site vehicle on lift or level ground.
2.Remove oil filler level plug. If necessary, inject
new oil into the gearbox until it runs out of filler
hole. Fit plug. Tighten to
30 Nm.
RENEW MANUAL GEARBOX OIL - Tdi - Mpi
RENEW MANUAL GEARBOX OIL - V8i

MAINTENANCE
13
MAINTENANCE
RENEW AUTOMATIC GEARBOX FLUID AND OIL
SCREEN
1.Site vehicle on lift or level ground. Place
container to drain gearbox fluid into. Disconnect
battery negative lead.
2.Remove gearbox dipstick, located at rear of right
hand rocker cover, to aid oil drainage. Release
plug from bottom of sump and allow fluid to drain
completely.
3.Refit plug using a new sealing washer. Tighten
to
10 Nm
Refill ZF Automatic Gearbox and Check Fluid
Level.
NOTE: The fluid level must checked when
fluid is cold and engine idling in park.
4.Ensure vehicle is on level ground.
5.Refill or top-up with correct quantity and grade of
fluid.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids
6.Start and run engine. Apply footbrake, select
position 1 then back to park. Check fluid level,
this must be between the two marks on the
dipstick.
Oil screen replacement ZF automatic gearbox.
See AUTOMATIC GEARBOX, Repair, Oil Screen

10MAINTENANCE
14
MAINTENANCE
RENEW TRANSFER GEARBOX OIL
1.Site vehicle on lift or level ground.
2.Disconnect battery negative lead.
3.Clean immediate area around filler/level and
drain plugs.
WARNING: When draining gearbox care
should be taken to ensure that oil is not
hot as personal scalding could result.
4.Place a container under gearbox to drain oil into.
5.Remove filler/level plug to vent gearbox and
assist draining.
6.Remove drain plug and allow oil to drain.
7.Thoroughly clean drain plug threads prior to
applying fresh 'Hylomar' sealant. Fit plug
Tighten to
30 Nm.
8.Fill gearbox with correct quantity and grade of oil
until oil seeps from filler level hole. Wipe away
any surplus oil.
9.Thoroughly clean filler/level plug threads prior to
applying fresh 'Hylomar' sealant. Fit plug
Tighten to
30 Nm.
10.Reconnect battery negative lead.
CHECK/TOP UP TRANSFER GEARBOX OIL
1.Site vehicle on lift or level ground.
2.Disconnect battery negative lead.
3.Clean immediate area around filler/level plug.
4.Remove plug and fill gearbox with recommended
grade of oil, until oil starts to seep from filler/level
hole.
5.Clean any previously applied sealant from
filler/level plug.
6.Apply Hylomar sealant to threads of plug and
refit plug. Tighten to
30 Nm.
7.Wipe away any surplus oil.
8.Reconnect battery negative lead.

12ENGINE
4
REPAIR 22.Disconnect feed pipe and spill return pipe from
injector pump.
23.Disconnect both pipes from fuel lift pump.
24.Disconnect servo hose from vacuum pump.
25.Remove three retaining nuts and disconnect
exhaust down pipe.
26.Remove oil cooler pipes from oil filter adaptor.
27.If automatic transmission is fitted, disconnect
feed and return pipes at gearbox oil cooler.
Remove retaining bracket from LH side of
cylinder block and release both oil cooler pipes.
28.Support gearbox.
29.Disconnect ground strap from starter motor.
30.On vehicles with automatic transmission, remove
fixings and detach drive plate housing access
panel and gasket.31.Working through drive plate housing aperture
mark the torque convertor and drive plate to
facilitate reassembly.
32.Remove the four convertor to flexible drive
securing bolts, rotating crankshaft to gain access
to each individual bolt.
33.Fit engine lifting bracket to the two RH rear
cylinder head fixing bolts.
34.Using suitable hoist, fit lifting chains to engine.
35.Remove four bolts, from both sides, securing
front engine mounting brackets to cylinder block.
36.Remove two bolts, from both sides, securing
front engine mounting bracket to bell housing.

Tdi
5
REPAIR
37.Remove nuts and plain washers securing front
engine mountings to chassis,and lift both engine
mounting bracket assemblies from vehicle.
38.Remove engine to bell housing fixings. Leave
starter motor attached.
39.Raise engine to separate from transmission.
40.Check all connections to engine have been
disconnected.
41.Remove engine.Refit
42.Apply Hylomar to mating faces of bell housing.
Lubricate splines of gearbox primary pinion with
Rocol MV 3.
If automatic transmission, coat the four drive
plate to torque convertor bolts with Loctite 290.
Tighten to
39 Nm.
43.Lower engine and locate with transmission.
If manual transmission locate primary pinion into
clutch and engage bell housing dowels. Fit
engine to bell housing fixings. Tighten to
40 Nm.
If automatic transmission fixings. Tighten to46
Nm.
44.Raise engine, refit front engine mounting
brackets to cylinder block and bell housing.
45.Remove gearbox support and lower engine.
46.Tighten front engine mountings to chassis
fixings. Tighten to
45 Nm.
47.Reverse removal procedure. 1 to 37.

12ENGINE
8
REPAIR CAMSHAFT DRIVE BELT AND GEARS
Service repair no - 12.65.18
TIMING BELT
Remove
1.Remove front cover plate.
See Front Cover
Plate
2.Position engine at TDC on No. 1 cylinder.
3.If manual gearbox: Remove blanking plug from
flywheel housing and insert timing tool
LRT-12-044. If EDC - timing tool LRT-12-085
must be used.
If automatic gearbox:Sited to the rear of the
engine sump on engine backplate is a blanking
plate. Remove 2 blanking plate bolts and insert
timing tool LRT-12-044 into the larger bolt hole.
4.Engage timing tool pin with slot in flywheel.
5.Check correct alignment of timing mark on
camshaft gear and that crankshaft key aligns
with cast arrow on housing.
6.Insert pin from special tool LRT-12-045 in
injection pump gear and through into pump
flange.
NOTE: If the camshaft gear is to be
removed during these operations its
retaining bolt should be slackened before
the timing belt is removed.
7.Slacken belt tensioner bolt.
8.Remove idler pulley.
9.Remove timing belt.
NOTE: During use, a belt develops a wear
pattern relative to its running direction, if
the original belt is to be re-used it must be
refitted so that it rotates in the original direction.
CAUTION: Belts must be stored on edge
on a clean surface and in such a manner
that bends are not less than 50 mm radius.
Do not bend belts at an acute angle or radius of
less than 50 mm, otherwise premature failure
could result.
10.Mark belt direction of rotation, using soft chalk,
to ensure correct refitment.

12ENGINE
14
REPAIR FLYWHEEL
Service repair no - 12.53.07
Remove
1.Disconnect battery negative lead.
2.Remove gearbox.
See MANUAL GEARBOX,
Repair, R380 Manual Gearbox
3.Remove clutch.See CLUTCH, Repair, Clutch
Assembly
4.Fit two long 8mm bolts into the clutch bolt holes,
diametrically opposite, to use as handles when
lifting the flywheel off the crankshaft.
5.Remove fan cowl
6.Fit crankshaft pulley retainer LRT-12-080 and
secure with four bolts, to restrain crankshaft
while removing flywheel retaining bolts.
7.Remove the bolts and lift off flywheel.
NOTE: To prevent excessive flywheel
run-out, ensure that the mating faces of
the flywheel and crankshaft are clean.Refit
8.Locate the flywheel on the crankshaft and
secure with new patched retaining bolts,
progressively tighten to
147 Nm.
9.Check the flywheel for possible run-out by
mounting a dial test indicator with the stylus in a
loaded condition resting on the flywheel face at a
radius of 114mm from the centre.
10.Turn the flywheel and check that run-out does
not exceed 0,05 to 0,07mm. Should run-out be
excessive, remove the flywheel and check again
for irregularities on the crankshaft and flywheel
mating faces and the dowel.
11.Reverse removal procedure. 1 to 6.