1995 LAND ROVER DISCOVERY alarm

ELECTRICAL
11
DESCRIPTION AND OPERATION ANTI-THEFT ALARM BUILT-IN TEST (96 MODELS)
NOTE: The handset should be detached
from the key to allow perimetric testing of
the alarm system. The system will
automatically switch to volumetric testing if the
handset is in close proximity to the starter switch.
The built-in test procedure can be accessed providing
the following conditions exist:
Alarm disarmed.
Ignition off.
Doors unlocked.
Bonnet[hood] closed.
The test mode can be entered by completing the
following instructions within 5 seconds:
1.Open bonnet.
2.Turn starter switch on.
3.Open driver's door (far enough to activate
switch).
4.Turn starter switch off.
5.Turn starter switch on.
If the test mode has been correctly accessed, the
sounder/horn will operate briefly and the anti-theft
alarm indicator and hazard warning lights will flash.
Perimetric tests
The anti-theft alarm indicator light and the hazard
warning lights will flash when:
1.Door switches are activated;
2.The bonnet is opened;
3.Sill switches are activated;
4.Key switches are activated.
NOTE: Operation of key switches can be
verified by turning the key in the relevent
direction so as not to simultaneously
activate the sill switch. If the key switch changes
state, the change should be detected but the sill
switch will not be activated.
Volumetric tests
Press the unlock button or move the handset close to
the starter switch to disable perimetric testing and
enable volumetric testing. If movement is detected
within the vehicle by the ultrasonic sensor it will be
indicated by flashing the anti-theft alarm indicator and
hazard warning lights.
NOTE: Exit anti-theft alarm built-in test by
turning starter switch to the off position.

ELECTRICAL
1
REPAIR FUSE BOX - INTERIOR
Right Hand Drive shown
The interior fusebox is fitted below the steering column, behind the trim panel. It comprises of three integral units.
'A'Main fusebox,'B'Satellite 2,'C'Satellite 1.
A label in the fusebox cover shows the circuits protected, the fuse rating and their locations. Access is by
releasing the fixing screws and lowering the panel.
'A' Main fusebox
1. Stop lights, direction indicators
2. LH side light
3. Radio/cassette/CD player
4. RH headlight main beam
5. LH headlight main beam
6. Cigar lighter
7. Airbag SRS
8. RH side lights
9. Rear fog guard lights
10. RH headlight dipped beam
11. LH headlight dipped beam
12. Multi-function unit
13. Ignition feed for Multi-function unit
14. Instruments, reversing lights
15. Air conditioning, windows
16. Washers & wipers - front
17. Starter, glow plug
18. Wash/wipe - rear, mirrors, cruise control
'B' Satellite 2
1. Electric windows - front
2. Electric windows - rear
3. Anti-lock braking
4. Central door locking
5. Electric sun roof
6. Trailer lights
'C' Satellite 1
1. Anti-theft alarm
2. Headlight washers
3. Engine management
4. Anti-lock brakes
5. Anti-theft alarm
6. Rear air conditioning, heater
'D' Spare fuses (5 off)

ELECTRICAL
3
REPAIR BATTERY
Service repair no - 86.15.01
NOTE: Some vehicles are fitted with a
battery backed-up sounder. Disconnecting
the vehicle battery will cause the alarm to
sound unless the following procedure is followed:
1.Turn starter switch 'ON' then 'OFF'.
2.Disconnect battery WITHIN 15 SECONDS (see
WARNING).
If alarm is accidentally activated, ensure sounder is
connected and silence by turning the starter switch to
position II.
Remove
WARNING: During battery removal or
before carrying out any repairs or
maintenance to electrical components
always disconnect battery negative lead first. If
positive lead is disconnected with negative lead in
place, accidental contact of wrench to any
grounded metal part could cause a severe spark,
possibly resulting in personal injury. Upon
installation of battery connect positive lead first.
3.Disconnect both battery leads, negative first.
4.Release four nuts securing battery bracket in
position.
5.Remove bracket.
6.Remove battery.
Refit
7.Reverse removal procedure.
NOTE: Coat battery clamps and terminals
with petroleum jelly before refitting.DISTRIBUTOR-LUCAS 35 DLM8 - V8i
Service parts
1. Cap
2. HT brush and spring
3. Rotor arm
4. Insulation cover
5. Pick-up module and base plate assembly
6. Vacuum unit
7. Amplifier module
8. 'O'-ring oil seal
9. Gasket

ELECTRICAL
11
REPAIR HANDSET INITIALISATION
NOTE: New handsets are supplied in pairs.
If a new handset is required, it will require
initialisation to the ECU using the
following procedure:
1.Starting conditions: ignition off, doors unlocked,
bonnet switch depressed.
2.Carry out instructions 3. to 9. within 8 seconds.
3.Switch ignition ON.
4.Switch ignition OFF.
5.Lock doors.
6.Unlock doors.
7.Release bonnet switch.
8.Switch ignition ON.
9.Switch ignition OFF.
If alarm is correctly accessed, horn will sound and
LED will light. It is now possible to programme two
handsets of correct frequency to vehicle alarm ECU.
This must be carried out within two minutes.
10.Press and hold down button on first handset until
dash LED flashes.
11.Repeat instruction 10. for second handset.
12.The LED will extinguish if both handsets have
been initialised correctly.CENTRAL DOOR LOCKING
Where electrically operated central door locking is
fitted, locking or unlocking the drivers door from
outside by key operation, or from the inside with the
sill knob automatically locks or unlocks the passenger
and rear doors.
Front and rear passenger doors can be independently
locked or unlocked from inside the vehicle by sill knob
operation but can be overidden by further operation of
the driver's door locking control.
On rear doors, where side facing fold down seats are
fitted, a child safety lock is provided which can be
mechanically pre-set to render the interior door
handles inoperative.
Failure of a door actuator will not affect the operation
of the remaining doors and the door with the
inoperative actuator can still be locked or unlocked
manually.
The actuator unit fitted to the driver's door is the
master actuator and is identified from the actuators
fitted to the passenger and rear doors by having a
white connecting link, whereas the passenger and
rear door actuators have grey coloured connecting
links.
NOTE: Actuator units are non-servicable, if
a fault should occur replace the unit with a
new one.

ELECTRICAL
43
REPAIR ANTI-THEFT ALARM ECU (96 MODELS)
Service repair no - 86.55.85
Remove
1.Remove 4 studs securing fascia left hand
closing panel.
2.Remove closing panel.
3.Disconnect 2 multiplugs from ECU.
4.Remove nut securing ECU/relay bracket.
5.Lower bracket.
6.Remove 2 nuts securing ECU to bracket.
7.Remove ECU.
NOTE: A new ECU must be initialised
using TestBook.
Refit
8.Reverse removal procedure.HANDSET (96 MODELS)
If vehicle does not respond to handset immediately, it
may have lost synchronisation. To re-synchronise,
press either button, 4 times in quick succession. If
handset still fails to respond, check batteries, refer to
Owner's handbook. If batteries are okay, it may be
necessary to use emergency key access, refer to
Owner's handbook.
NOTE: New handsets must be initialised
using TestBook.
PASSIVE COIL (96 MODELS)
Service repair no - 86.77.35
Remove
1.Remove steering column shroud.
See
STEERING, Repair, Steering column shroud
2.Release multiplug from harness clip and
disconnect.
3.Release passive coil from starter switch.
4.Remove bulb holder/starter switch shroud.
5.Remove coil.
Refit
6.Fit coil, ensuring switch illumination bulb harness
passes through large cut-out.
7.Secure coil with cable tie.
8.Position bulb holder/starter switch shroud and
locate bulb.
9.Locate bulb holder/starter switch shroud,
ensuring cut-out in shroud aligns with lug on
starter switch.
10.Connect multiplug and secure to clip.
11.Fit column shroud.

86ELECTRICAL
44
REPAIR BONNET SWITCH
Service repair no - 86.55.89
Remove
1.Remove 2 bolts securing sounder, move
sounder aside.
2.Locate and disconnect bonnet switch multiplug.
3.Release and remove switch.
Refit
4.Reverse removal procedure.ULTRASONIC SENSOR
Service repair no - 86.77.32
Remove1.Release sensor from switch panel.
2.Disconnect multiplug and remove sensor.
Refit
3.Reverse removal procedure.
ANTI-THEFT ALARM INDICATOR LIGHT (96
MODELS)
Service repair no - 86.45.61
See Instrument illumination and warning light
bulbs
ENGINE IMMOBILISATION WARNING LIGHT (96
MODELS)
Service repair no - 86.45.61
See Instrument illumination and warning light
bulbs