1995 LAND ROVER DISCOVERY oil filter

Tdi
19
REPAIR OIL TEMPERATURE CONTROL VALVE
Service repair no - 12.60.69
Remove
1.Disconnect oil cooler pipes.
2.Remove two bolts and carefully withdraw
thermostat extension housing (1) complete with
O ring seal (2), thermostat (3), two washers (4)
and spring (5).
3.Clean adaptor housing.
4.Inspect all parts and renew as necessary.
Refit
5.Fit thermostat to extension housing ensuring pin
locates in hole.
6.Fit two washers and spring to thermostat.
7.Fit a new 'O' ring to extension housing.
8.Insert spring into adaptor and secure extension
housing to adaptor with bolts. Tighten to
9 Nm.
OIL FILTER HEAD GASKET
Service repair no - 12.60.03
Renew
1.Disconnect oil cooler pipes.
2.Disconnect pressure switch lead.
3.Remove securing bolts and withdraw head
complete with gasket.
4.Clean mating faces.
5.Refit head with new gasket.
6.Secure with bolts. Tighten to
45 Nm.
7.Refit pipes and reconnect pressure switch.

Tdi
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine block
Bearing cap 133...............................................................................................
Blanking plug, oil gallery, rear 37....................................................................
Oil squirt jet assembly 17................................................................................
Drain plug, cylinder block 25...........................................................................
Oil squirt jet, vacuum pump cam 7.................................................................
Connecting rod to cap 59................................................................................
Oil pick up assembly to bearing cap 9...........................................................
Oil pick up assembly to front cover 25............................................................
Camshaft thrust plate 9..................................................................................
Oil drain pipe to block (internal) 25.................................................................
Oil drain pipe to block (external) 25................................................................
Sump to cylinder block and front cover 25......................................................
Drain plug, oil sump 35...................................................................................
Tappet guide 14..............................................................................................
Breather side cover assembly 25....................................................................
Baffle plate to breather side cover 4..............................................................
Vacuum pump 25............................................................................................
Fuel lift pump 25.............................................................................................
Flywheel housing 45.......................................................................................
Flywheel housing clutch cover stud 10...........................................................
Plug, flywheel housing 12...............................................................................
Rear oil seal assembly 25...............................................................................
Oil filter adaptor 45..........................................................................................
Waxstat adaptor to oil filter adaptor 9............................................................
Oil pressure switch 17.....................................................................................
Oil filter, spin on 13.........................................................................................
Oil cooler unions to filter adaptor 45...............................................................
Oil level tube 25..............................................................................................
Engine mounting foot to cylinder block 85......................................................
Engine mounting foot to flywheel housing 45.................................................
Engine mounting foot rubber to mounting foot (bolt and nut) 85.....................
Flywheel to crankshaft 146..............................................................................
Clutch cover plate to flywheel 34....................................................................
Flex drive plate to crankshaft (auto) 146..........................................................
Flex drive plate to ring gear (auto) 25.............................................................
Flex drive plate to torque converter (auto) 45.................................................

Tdi
3
SPECIFICATIONS, TORQUE Turbo charger oil drain adaptor to block 42....................................................
Oil drain pipe to turbocharger 25....................................................................
Turbocharger oil drain pipe to adaptor 38.......................................................
Turbocharger oil feed pipe adaptor to block 25...............................................
Turbocharger oil feed pipe to adaptor 25........................................................
Oil feed pipe to turbocharger 19.....................................................................
Turbocharger to cylinder head (stud) 10.........................................................
Turbocharger to cylinder head (nut) 45...........................................................
Turbocharger to blanking plate 25..................................................................
Turbocharger to EGR valve 25.......................................................................
EGR delivery tube to valve 25........................................................................
EGR delivery tube to mixing tube 25..............................................................
Fuel lift pump to filter (union) 15.....................................................................
Fuel filter from lift pump (banjo bolt) 33...........................................................
Fuel filter to fuel injection pump (banjo bolt) 33..............................................
Fuel injection pump from fuel filter (banjo bolt) 25..........................................
Injector pipes to injectors and fuel injection pump 29.....................................
Spill rail to injectors (banjo bolt) 10.................................................................
Spill rail to injection pump (banjo bolt) 25.......................................................
Boost pipe injection pump (banjo bolt) 10.......................................................
Plug, rear of injection pump 29.......................................................................
PAS pump to mounting plate 25.....................................................................
PAS pump mounting plate to auxiliaries mounting bracket 25........................
PAS pump pulley to hub 25............................................................................
Generator to auxiliaries mounting bracket 25.................................................
Starter motor (bolt and nut) 45........................................................................
Tachometer electrical connection 4...............................................................
Air conditioning compressor
Compressor mounting bracket to front cover 45.............................................
Compressor to mounting bracket (stud) 8......................................................
Compressor to mounting bracket (nut) 25......................................................
Belt tensioner pulley to tensioner arm 45........................................................
Belt tensioner assembly to front cover plate 25..............................................
Idler pulley to front cover plate 45...................................................................
Compressor belt guard (nut) 25......................................................................
Sensors to water outlet elbow (air/con) 25......................................................
Blanking plug, water outlet elbow (air/con) 25................................................
Generator mounting bracket to front cover 45................................................
Generator to mounting bracket 85..................................................................
Generator pulley to hub 95.............................................................................
Generator belt guard 25..................................................................................

12ENGINE
2
DESCRIPTION AND OPERATION
1. Cylinder block
2. Pistons and gudgeon pins (8)
3. Connecting rods (8)
4. Core plugs
5. Camshaft
6. Dipstick
7. Camshaft key
8. Timing chain
9. Camshaft sprocket
10. Distance piece
11. Distributor drive gear
12. Distributor
13. Front cover
14. Front cover oil seal
15. Coolant pump
16. Crankshaft damper / pulley17. Crankshaft sprocket
18. Crankshaft sprocket key
19. Crankshaft
20. Centre main bearing shells (2)
21. Crankshaft rear oil seal
22. Spacer
23. Adaptor plate
24. Rear main bearing cap, shell and side seals
25. Connecting rod caps
26. Main bearing caps and shell bearings
27. Oil filter
28. Oil pump suction pipe/strainer
29. Oil sump
30. Oil sump drain plug
31. Oil pump drive key

V8i
3
DESCRIPTION AND OPERATION
1. Cylinder heads (2)
2. Rocker covers (2)
3. PCV filter
4. Rocker shafts (2)
5. Hydraulic tappets (8)
6. Pushrods (8)
7. Rocker brackets (8)
8. Rocker arms (4) left and (4) right
9. Rocker shaft springs (6)
10. Inlet manifold
11. Plenum chamber lower
12. Ram pipes (8)13. Plenum chamber upper
14. PCV air intake filter
15. Oil filler
16. Thermostat
17. Thermostat cover
18. Inlet valve seal, spring, cap and collets (8)
19. Exhaust valve seal, spring, cap and collets (8)
20. Inlet valve and seat (8)
21. Exhaust valve and seat (8)
22. Inlet manifold gasket and seals
23. Cylinder head gaskets (2)
24. Valve guides (16)

12ENGINE
4
DESCRIPTION AND OPERATION Lubrication system
The V8i full flow lubrication system uses a gear type oil pump which is driven from the front of the crankshaft. The
oil pump gears are housed in the front cover and the pressure relief valve, warning light switch and filter are also
fitted to the front cover.
Oil drawn through the centrally located steel gauze strainer in the sump, is pumped under pressure through oil
cooler located in the lower half of the main coolant radiator. The cooled oil then passes through the filter, before
being distributed from the main gallery via drillings, to the various components in the engine.
Lubrication to the thrust side of the cylinders is by oil grooves machined in each connecting rod big end joint face,
which are timed to align with holes in the big end journals on the power and exhaust strokes.
Lubrication system
1. Oil to cooler
2. Oil from cooler

12ENGINE
2
FAULT DIAGNOSIS ENGINE NOISES
Excessive or obtrusive noise from the engine
compartment originates from three main sources:
A. The exhaust system, which makes an
unmistakable and easy to diagnose noise.
B. External components emit the greatest variety of
noises, but are also easy to diagnose by simply
removing the drive belt.
C. Engine internal mechanical noises which can
vary in volume and pitch and may be a
combination of, tapping - knocking or rumbling,
are the most difficult to diagnose. The following
is therefore a guide to diagnosis of engine
internal mechanical noises only.
Engine internal mechanical noises.
Single or multiple, light tapping noise, particularly
when engine is cold.
See Description and
operation, Description
1.Is engine oil level correct?
NO - Top up to correct level.
See
LUBRICANTS, FLUIDS AND
CAPACITIES, Information,
Recommended Lubricants and Fluids
YES - Continue.
2.Is the lubricating pressure correct?
NO -
See Engine Oil Pressure Test
YES - Suspect valve operating mechanism.
3.To confirm diagnosis, remove the rocker covers
and with the engine idling, insert a feeler gauge
of 0,015mm between each rocker and valve
stem. A faulty valve operating mechanism will
emit a different noise when the feeler gauge is
inserted.
See Repair, Rocker Shaft Renew
Heavy knocking noise (particularly on load and
when engine is hot).
See Description and
operation, Description
1.Is engine oil level correct?
NO - Top up to correct level.
See
LUBRICANTS, FLUIDS AND
CAPACITIES, Information,
Recommended Lubricants and Fluids
YES - Continue.
2.Is the lubricating pressure correct?
NO -
See Engine Oil Pressure Test
YES - Drain engine oil and filter, and examine
for metallic contamination.
3.Is the oil contaminated with metal particles?
YES - Suspect faulty big end bearings. To
confirm diagnosis, short out the ignition to
each spark plug in turn. The noise will
disappear or be reduced when the
cylinder with the faulty big end is shorted
out.
4.If noise is not conclusively diagnosed, check the
security of the flywheel and crankshaft front
pulley. Temporarily release the drive belt to
reduce general noise level and use a
stethoscope to locate source of noise.
Heavy rumbling noise (particularly during hard
acceleration).
See Description and operation,
Description
1.Is engine oil level correct?
NO - Top up to correct level.
See
LUBRICANTS, FLUIDS AND
CAPACITIES, Information,
Recommended Lubricants and Fluids
YES - Continue.
2.Is the lubricating pressure correct?
NO -
See Engine Oil Pressure Test
YES - Drain engine oil and filter, and examine
for metallic contamination.
3.Is the oil contaminated with metal particles?
YES - Suspect faulty main bearings. If noise is
not conclusively diagnosed, check the
security of the flywheel and crankshaft
front pulley. Temporarily release the drive
belt to reduce general noise level and use
a stethoscope to locate source of noise.

12ENGINE
4
FAULT DIAGNOSIS 3.Are fuel supply, tank, pump, ventilation and
emission control systems in correct working
order or the fuel contaminated?
NO -
See FUEL SYSTEM, Repair, Fuel
Filter See FUEL SYSTEM, Repair,
Fuel Tank See FUEL SYSTEM, Repair,
Fuel Pump and Sender Unit
YES - Suspect valves held open by hydraulic
tappets due to high oil pressure.
See
Engine Oil Pressure Test
4.Is oil pressure high?
YES - Remove oil filter and cooler adaptor and
check pressure relief valve strainer gauze
for blockage and that the relief valve is
not stuck closed.
See Description and
operation, Description
NO - Carry out cylinder compression tests to
determine condition of head gaskets and
valves.
See Cylinder Compression -
Test
5.Are cylinder compressions satisfactory?
NO -
See Repair, Cylinder Heads - Renew
YES - Check brake vacuum connections.See
BRAKES, Description and operation,
Brake Servo Unit
Check heater/ventilation unit vacuum connections.
See HEATING AND VENTILATION, Description and
operation, Heating and Ventilation Unit
If problem is not diagnosed: Continue.
6.Are the brakes binding?
YES - Investigate cause of binding.
NO - Continue.
7.Automatic Transmission only. Is the Torque
Converter and Transmission operating correctly?
Carry out Road test, Static tests and Stall tests
to determine condition of Automatic
transmission.
If problem is not diagnosed: repeat tests starting at 1.Engine backfires into exhaust system
1.Are there any leaking joints/connections or holes
in the exhaust system?
YES -
See MANIFOLD AND EXHAUST
SYSTEM, Repair, Exhaust System
Complete
NO - Continue.
2.Is distributor fitted correctly, HT leads in correct
firing order and routed correctly?
NO -
See ELECTRICAL, Repair, Distributor
- V8i
YES - Continue.
3.Is air fuel ratio correct?
NO - Check multiport fuel injection.
See
Electrical Trouble Shooting Manual.
Check brake vacuum connections.See
BRAKES, Description and operation, Brake
Servo Unit
Check heater/ventilation unit vacuum
connections.
See HEATING AND
VENTILATION, Description and operation,
Heating and Ventilation Unit
Check the crank case and fuel tank ventilation
system.
See EMISSION CONTROL,
Description and operation, Emission Control
YES - Continue.
4.Are cylinder compressions satisfactory?
NO - Carry out compression test to check for
leaking gaskets valves etc.
See
Cylinder Compression - Test
See Repair, Cylinder Heads - Renew
If problem is not diagnosed: repeat tests starting
at 1.