1995 LAND ROVER DISCOVERY key battery

76CHASSIS AND BODY
40
REPAIR SUNROOF ELECTRIC CONTROL UNIT
Service repair no - 76.82.73
The control unit serves both front and rear sunroofs
and is sited above the front switches behind
headlining.
Remove
1.Disconnect battery negative lead.
2.Ensure sunroof is in normally closed position.
NOTE: If the electric motor has failed the
sunroof can be closed manually using an
allen key to turn motor spindle.
3.Remove switch panel from stowage pocket
panel
4.Remove interior lamp from stowage pocket
panel
5.Remove alarm ultrasonic unit.
6.Unscrew ten fixings and remove stowage pocket
from headlining.
7.Disconnect electric plugs from control unit.
8.Remove two retaining screws and control unit.
Refit
9.Reverse removal procedure.

86ELECTRICAL
6
DESCRIPTION AND OPERATION ALARM COMPONENT LOCATIONS (96 MODELS)
COMPONENT LOCATION
1. Electronic control unit (ECU) and relays Under dash (passenger side).................
2. Anti-theft alarm indicator light Instrument panel..................................
3. Engine immobilisation warning light (EIWL) * Instrument panel..........
4. Passive coil Over starter switch barrel.............................................................
5. Bonnet switch RH engine compartment..........................................................
6. Door switches
7. Ultrasonic sensor Interior light switch panel....................................................
8. Lock barrel, sill buttons
9. Handset and key
10. Battery backed-up sounder or horn * RH engine compartment......................
11. Immobilisation unit (spider) * Above heater...................................
12. Aerial Part of fascia harness.......................................................................
* where applicable

86ELECTRICAL
8
DESCRIPTION AND OPERATION DETECTION COMPONENTS
Switches
Perimetric protection for the vehicle is provided by
ECU inputs connected to the following:
Key switches (including starter)
Sill buttons
Bonnet switch
Door switches
Ultrasonic sensor
The ultrasonic sensor is located on the interior light
switch panel and triggers the alarm if movement is
detected.
WARNING INDICATORS
Battery backed-up sounder
The battery backed-up sounder is located in the
engine compartment and provides an audible warning
whenever the alarm is triggered.
NOTE: Disconnecting the vehicle battery
will result in the alarm sounding if the
correct procedure has not been followed.
See Repair, Battery.
Engine immobilisation warning light (EIWL)
The engine immobilisation warning light is located in
the instrument pack and provides a visual indication
that the engine is immobilised.
Anti-theft alarm indicator light
The anti-theft alarm indicator light is located in the
instrument pack and provides a visual indication of the
alarm status.
Inertia switch and central door locking
As a safety feature, the alarm system is designed to
recognise the inertia switch and via the ECU, unlock
the doors in the event of a collision.
NOTE: This feature only applies when the
starter switch is in the on position.ANTI-THEFT ALARM OPERATION (96 MODELS)
Full arming and immobilisation
Locking the vehicle using the handset immobilises the
engine and initializes both volumetric and perimetric
protection, providing:
1.After a lock signal has been received, a period of
15 seconds has elapsed during which no
movement is detected inside the vehicle;
2.No door or bonnet is open.
NOTE: If either of the above conditions are
not satisfied, the alarm will only be
partially armed. This is a mislock condition
which will be made apparent by a delay of 10
seconds before the anti-theft alarm indicator
begins to flash.
Disarming the alarm
NOTE: ALWAYS disarm the alarm using
the handset.
Unlocking with the key will not disarm the alarm or
mobilise the vehicle. If the handset fails to unlock the
vehicle
See Repair, Handset.
Partial arming and immobilisation
The alarm will be partially armed and the engine
immobilised if the vehicle is locked with the handset or
key, if:
1.After a lock signal has been received, a period of
15 seconds has elapsed during which movement
is detected inside the vehicle;
2.A door or bonnet is open.
NOTE: This is a mislock condition which
will be made apparent by a delay of 10
seconds before the anti-theft alarm
indicator begins to flash. Subsequent closure of
the offending aperture will cause the alarm to
attempt full arming as previously described.
Immobilisation
The vehicle will be automatically immobilised
whenever any of the following conditions occur:
1.The vehicle is locked using the handset.
2.The vehicle is locked using the key.
3.Thirty seconds after the starter switch has been
turned off AND the driver's door opened.
4.Five minutes after the starter switch is turned off
or the alarm disarmed.

ELECTRICAL
9
DESCRIPTION AND OPERATION Mobilisation
The vehicle can be mobilised using any one of the
following processes:
1.Placing the handset in close proximity to the
starter switch with the starter switch turned on
(normally achieved by placing the key in the
starter switch, providing the key and handset are
attached).
NOTE: Under normal circumstances the
remobilisation of the vehicle will not be
apparent.
2.Pressing unlock button on handset.
3.Pressing lock button on handset with starter
switch turned on.
4.Entry of EKA code using the key.
NOTE: Any attempt to start the vehicle
using the key (detached from the handset)
will be unsuccessful. Use one of the above
methods.
See Warning indicators.
Volumetric protection
When the vehicle is locked using the handset both
perimetric and volumetric protection are activated
providing there is no mislock condition.
Perimetric protection
The vehicle is always perimetrically protected when
the alarm is armed using the handset. Perimetric
protection only, can be achieved if the vehicle is
locked using the key.
NOTE: The handset should ALWAYS be
used for unlocking the vehicle. If the
handset fails to unlock the vehicle
See
Repair, Handset.
Battery backed-up sounder (BBUS)
The sounder provides audible indication of alarm
status including:
Anti-theft warnings;
Confirmation of access to built-in test.
NOTE: Disconnecting the vehicle battery
will result in the alarm sounding if the
correct procedure has not been followed.
See Repair, Battery.
Alarm horn
The horn provides audible indication (as BBUS) of
alarm status.
NOTE: Disconnecting the vehicle battery
will have no effect on the horn.
Engine immobilisation warning light (EIWL)
NOTE: Under normal circumstances the
light will not illuminate.
The light will only illuminate (after 2 seconds) if the
handset is detached from the key (or the handset
fails) and an attempt is made to start the vehicle.
Anti-theft alarm indicator light
The light flashes to indicate the alarm status.
If the alarm system is fully armed, the light will flash
rapidly for 10 seconds and then settle to the slow
(anti-theft deterrent) flash.
If the alarm system is perimetrically armed, the light
will intermittently flash rapidly for 10 seconds and then
settle to the slow (anti-theft deterrent) flash.
If the alarm system is partially armed, the light will
NOT emit the slow flash until 10 seconds after arming
(to allow the cause to be investigated).
If the vehicle has been left unlocked, providing the
driver's door is closed, the light will flash slowly
indicating immobilisation. If the driver's door is open,
the light will remain illuminated.
Emergency key access (EKA)
The emergency key access code should be entered in
accordance with the instructions in the Owner's
Handbook.

ELECTRICAL
3
FAULT DIAGNOSIS 1 2 3 4 SUSPECT
L * * * DISCHARGED BATTERY
* L L * IGN. SWITCH AND/OR
WIRING
* * L * COIL OR AMPLIFIER
* * * H AMPLIFIER GROUND
Key
*Expected Voltage
HVoltage higher than expected
LVoltage lower than expectedTEST 3:
Amplifier Switching
Connect voltmeter between battery positive (+ve)
terminal and H.T. coil negative (-ve) terminal.
Voltmeter should register 0 volts.
Switch ignition 'On', voltmeter should still register 0
volts.
Crank engine, voltmeter reading should increase
when cranking, in which case proceed to Test 5.
If no increase in voltage during cranking proceed to
Test 4.

ELECTRICAL
15
REPAIR Refit
9.If removed fit the mounting plate to the actuator.
10.Engage the actuator operating rod with hooked
end of the actuator link.
11.Fit the actuator and mounting plate to the door
and loosely secure with the four screws.
12.Set the mounting plate with the screws in the
centre of the slotted holes, then tighten the
screws.
13.Connect the actuator lead to the door harness.
14.Reconnect battery negative lead.
15.With the sill locking button held in position, set
the bellcrank to approximately the position it
would be in if the sill button was depressed to
half of its total movement.
16.At this setting check the electrical operation of
the door lock. Adjust the mounting plate as
necessary to achieve the correct setting. Fully
tighten the securing screws on completion.
17.Refit the vapour barrier.
18.Connect the sill button operating rod to the
bellcrank, hold in position, fit the door trim panel
and the door pull.
BULB REPLACEMENT
For bulb type and rating refer to rating shown on the
bulb or bulb replacement list.
See GENERAL
SPECIFICATION DATA, Information, Bulbs
HEADLIGHT
Service repair no - 86.40.02/13
Remove
1.Rotate three retaining clips 10 degrees, to align
with slots in headlight mounting plate.
2.Withdraw light unit
NOTE: Detach adjustment operating rod
on vehicles fitted with headlight levelling.3.Disconnect electrical multiplugs and remove
headlight unit.
4.Release spring clips and withdraw headlight
bulb.
Key
1. Headlight
2. Retaining clips
3. Bulb
4. Spring clip
5. Cover
6. Bulb sidelight
7. Plug
8. Plug sidelight
Refit
5.Reverse removal procedure.