1995 LAND ROVER DISCOVERY belt

CHASSIS AND BODY
15
REPAIR REAR DOOR CHECK STAY
Service repair no - 76.40.30
Remove
1.Remove the rear door from the vehicle.
See
rear door.
2.Invert the door on a suitable protected area.
3.Remove the two securing bolts and withdraw the
check stay assembly.
Refit
4.Reverse removal procedure.REAR COMPARTMENT LOWER TRIM PANELS
Service repair no - 76.13.03
Remove
1.Remove the fold down seat or pocket side panel,
whichever is applicable.
See rear fold down
seats.
2.Remove speaker by releasing screws and
disconnecting Lucars. Withdraw rear quarter trim
panel.
3.Remove the five trim panel retainers.
4.Ease the trim panel from its location, feed the
seat belts through the apertures and withdraw
the panel.
Refit
5.Reverse removal procedure.

76CHASSIS AND BODY
16
REPAIR ALPINE LIGHT TRIM CASING
Service repair no - 76.13.20
Remove
1.Remove RH 'E' post trim casing.
See 'E' post
trim casing - rh.
2.Remove rear seat belt anchorage retaining bolt
cover.
3.Remove bolt securing rear seat belt anchorage.
4.Remove 2 trim studs securing trim casing.
5.Release trim casing from 2 retaining studs.
6.Remove trim casing.
Refit
7.Fit and align trim casing and secure with studs.
8.Fit 2 trim studs securing trim casing.
9.Position seat belt anchorage, fit bolt and tighten
to
32 Nm (24 lbf ft).
10.Fit cover to seat belt anchorage bolt.
11.Fit 'E' post trim casing.
See 'E' post trim
casing - rh.

CHASSIS AND BODY
17
REPAIR FRONT BODYSIDE TRIM CASING
Service repair no - 76.13.01
Remove
1.Remove the grab handle.
2.Remove the rear compartment lower trim panel.
See rear compartment lower trim panels.
3.Remove the alpine light trim casing.See alpine
light trim casing.
4.Remove the bolts securing the upper and lower
seat belt mountings.
5.Remove the finisher from its location over the
seat belt inertia reel.
6.Remove the front seat belt guide from the upper
aperture in the casing.
7.Open the side window, remove the catch
securing screws and withdraw the catch trim.
8.Remove the side window hinge finishers.
9.Release the casing from the window rubber.
10.Release the rear seat belt from the guide
attached to the casing.
11.Fold down the rear seats and carefully ease the
casing from the fastenings.
12.Pass the front seat belt through the upper
aperture and withdraw the casing from the
vehicle.
Refit
13.Reverse removal procedure.
NOTE: Ensure that the trim material glued
to the door post is not wrinkled when the
door seal is fitted.
14.Tighten upper and lower seat belt fixings to
32
Nm (24 lbf ft)
.

CHASSIS AND BODY
19
REPAIR 'D' POST TRIM CASING
Service repair no - 76.13.73
Remove
1.Remove the rear compartment lower trim panel.
See rear compartment lower trim panels.
2.Remove the alpine light trim casing.See alpine
light trim casing.
3.Release the rear seat belt from the guide
attached to the casing.
4.Fold down the rear seats.
5.Release the D' post casing from the rear side
window seal and carefully ease the casing from
the fasteners.
Refit
6.Reverse removal procedure.BODY SIDE OPENING WINDOWS
Service repair no - 76.81.18
Remove
1.Remove the screws securing the catch to the
body and detach the catch trim.
2.Remove the hinge finishers from the hinges.
3.Remove the screws securing the glass to the
hinges, withdraw the glass and fixings taking
care not to lose the joint washers.
Refit
4.Reverse removal procedure.

76CHASSIS AND BODY
20
REPAIR BODY SIDE WINDOW HINGES
Service repair no - 76.81.47
Remove
1.Remove the window.
See body side opening
windows.
2.Remove the passenger grab handle.
3.Detach the front seat belt top mounting from the
door post.
4.Ease the trim panel away from the door post to
gain access to the window hinges.
5.Remove the screws securing the window hinges,
taking care not to lose the the packing washers
where fitted. Note the thickness and location of
any packing washers fitted.
Refit
6.Fit the hinges with packing washers fitted to the
locations and thickness noted during removal.
Do not fully tighten the screws at this stage.
7.Refit the glass to the hinges.
8.Locate the window catch trim and secure the
catch to the body.
9.Close the window and secure with the catch.
10.Check the alignment and squareness of the
glass, adjust as necessary by adding or deleting
washers and using the elongated slots in the
hinges for adjustment, finally tighten the screws.
11.Reposition the trim panel and refit the hinge
finishers.
12.Refit the top seat belt bracket and the grab
handle.REAR SIDE FIXED WINDOWS
Service repair no - 76.81.18
Remove
1.If fitted push out the glass and remove the
mounting rubber.
2.Remove the rear seat belt top fixing.
Refit
3.Thoroughly clean the opening to be glazed.
4.Clean the glass and fit the mounting rubber,
ensuring that the glass sits correctly in the
groove.
5.Fit a draw cord around the exterior of the
mounting rubber.
6.To aid assembly, coat the flange in the bodyside
with liquid soap.
7.Position the assembled glass and rubber
mounting to the opening in the body, with the
tails of the draw cord fed into the interior of the
vehicle.
8.With assistance from a second operator, pushing
the glass and mounting rubber into the opening,
pull the draw cord from the mounting rubber
enabling the seal to ride up over the retaining
flange.
9.Ease the inner section of the mounting rubber
over the interior trim panel.

CHASSIS AND BODY
25
REPAIR FRONT SEAT COVERS
Service repair no - 76.70.14
Cushion
Remove
1.Remove the seat from the base.
2.Invert the seat on a suitable clean bench.
3.Detach the seat cover retaining clips from the
frame.
4.Release the four wire hooks securing the squab
cover to the lower spring frame.
5.Release the cushion rear clip from the frame and
detach the cushion complete with cover.
6.Remove the cover from the cushion.
Refit
7.Reverse removal procedure.REAR PASSENGER SEAT
Service repair no - 76.70.37
Remove
1.Feed the seat belts through the seats into the
rear compartment.
2.With the seats in the upright position, remove the
bolts from the front of the hinges.
3.Fold the seats forward, remove the bolts from
the rear of the hinges and withdraw the seats
from the vehicle.
Refit
4.Reverse removal procedure.
5.Tighten fixing bolts to
8 Nm (6 lbf ft).

CHASSIS AND BODY
27
REPAIR REAR SEAT CUSHION COVER
Service repair no - 76.70.88/89
Remove
NOTE: The procedure for removing both
left and right hand seat cushions is the
same.
1.Remove the rear seat assembly from the
vehicle.
See rear passenger seat.
2.Remove the seat squab.
3.Remove the seat cushion.
4.Remove the cushion base cover retaining
screws and withdraw the cover.
5.Release the seat cover securing clips at the
frame and at the seat belt aperture.
6.Remove the cover from the cushion.
Refit
7.Reverse removal procedure.SPLIT REAR SEAT LOCKING MECHANISM
Service repair no - 76.70.51
Remove
1.Remove the front body side trim casing.
See
front body side trim casing.
2.Remove the three screws securing the latch to
the tower, noting that access to the single screw
is gained through the hole in the front of the
tower.
3.Retrieve the latch from the opening at the rear of
the tower. If necessary retrieve the single screw.
4.The operating rod can be removed from the latch
by releasing it at the plastic clip.
Refit
5.Reverse removal procedure. Setting the release
button to achieve a gap of 5 - 8 mm (3/16 - 5/16
in).

76CHASSIS AND BODY
28
REPAIR REAR FOLD DOWN SEATS
Service repair no - 76.71.23
Seat and squab
Remove
1.Locate the seat in the down position, release the
seat belt strap and buckle from their stowed
positions.
2.Remove 4 Torx screws from the lower brackets.
3.Fold the seat up and remove the 2 Torx screws
from the upper brackets. Collect 4 washers.
4.Remove seat assembly.
Refit
5.Position seat assembly, align upper brackets,
and secure with Torx screws tightened to
13 Nm
(10 lbf ft)
.
NOTE: Ensure washers are fitted in their
correct positions.
6.Align lower brackets, fit Torx screws and tighten
to
13 Nm (10 lbf ft).
7.Secure the seat belt strap and buckle to their
stowed positions.
Seat squab
Remove
8.Remove the seat assembly from the vehicle.
9.Remove the pivot bolts and washers securing
the seat squab to the frame.
NOTE: The pivot bolts, securing the seat
squab and cushion, are fitted with a wavy
washer under the head and a plain washer
between the link or bracket. Ensure that these
washers are fitted in the correct locations when
reassembling the seat.