1995 LAND ROVER DISCOVERY wheel bolts

WIPERS AND WASHERS
1
REPAIR WASHER RESERVOIR
Service repair no - 84.10.03.
Remove
1.Remove two bolts securing top of reservoir.
2.From underneath the wheelarch remove two
bolts securing base of reservoir.
3.Withdraw reservoir and disconnect tubing from
washer pumps and power wash.
4.Disconnect electrical leads from pumps.
Refit
5.Reverse removal procedure. 1 to 4.WASHER PUMP - WINDSCREEN, REAR WINDOW
OR POWER WASH
Service repair no - 84.20.21.
Remove
1.Remove washer reservoir.See Washer
reservoir
2.Disconnect washer tubing from pump.
3.Disconnect electrical leads from pump.
4.Pull top of pump away from its location in
reservoir and remove pump.
Note position of sealing gasket in reservoir.
Refit
5.Reverse removal procedure. 1 to 4.

84WIPERS AND WASHERS
6
REPAIR Refit
16.Reverse removal procedure.
17.Fit wiper motor to support plate using new
sealing bushes at the motor spindle as
necessary.
18.When positioning assembled motor and support
plate use a new seal and bushes, if necessary.
REAR DOOR WIPER MOTOR
Service repair no - 84.35.12.
Remove
1.Disconnect battery negative lead.
2.Remove rear door trim panel.
3.Remove spare wheel.
4.Remove wiper arm and grommet.
5.Remove nut, plain washer and seal from drive
spindle.
6.From inside the door, disconnect wiper motor
leads from door harness at multi-plug.
7.Remove bolts securing wiper motor mounting
bracket and negative lead to inner door panel.
8.Withdraw motor spindle from outer door panel
and manoeuvre wiper motor from door casing
complete with the spindle spacer.
9.Remove two rubber mounted nuts securing
mounting bracket to motor and detach bracket.
Refit
10.Reverse removal procedure. 1 to 9.
NOTE: If a new wiper motor assembly has
been fitted, before fitting the wiper arm.
Reconnect battery negative lead. Operate
wiper motor to ensure that motor spindle is in
park position.

86ELECTRICAL
46
REPAIR STARTER MOTOR - 4.0 V8
Service repair no - 86.60.01
Remove
1.Disconnect battery negative lead.
2.Raise vehicle on ramp.
3.Remove heated oxygen sensor from RH front
exhaust pipe.
See EMISSION CONTROL,
Repair, Heated Oxygen Sensor (HO2S) - 4.0
V8
4.Mark front propeller shaft and drive flanges for
assembly reference.
5.Remove 4 nuts and bolts securing propeller
shaft flange.
NOTE: Raise 1 front road wheel and rotate
propeller shaft to gain access to all
fixings.
6.Tie propeller shaft aside.
7.Position starter motor heat shield above motor.
See Starter Motor Heat Shield - 4.0 V8
8.Disconnect Lucar from solenoid.
9.Remove nut securing feed wires to starter
solenoid and disconnect from terminal.

ENGINE
2
OVERHAUL
6.Remove timing belt front cover.
7.Remove and discard gasket.
8.Remove and discard crankshaft front oil seal
from timing belt front cover.
9.Temporarily fit crankshaft pulley bolt to
crankshaft.
Manual gearbox
10.Remove plug from bottom of flywheel housing.
11.Rotate crankshaft clockwise using crankshaft
pulley bolt until toolLRT-12-044can be
located in slot in flywheel.
CAUTION: Do not rotate crankshaft
anti-clockwise and do not use camshaft or
fuel injection pump gear bolts to rotate
crankshaft.
Automatic gearbox
12.Rotate crankshaft clockwise using crankshaft
pulley bolt until toolLRT-12-044can be
inserted through hole in engine plate and into
slot in drive plate.
CAUTION: Do not rotate crankshaft
anti-clockwise and do not use camshaft or
fuel injection pump gear bolts to rotate
crankshaft.

ENGINE
OVERHAUL9
5.Check that timing pinLRT-12-045moves
freely in and out of injection pump hub, if pin
does not move freely, slacken 3 bolts, move
gear slightly and re-check.
6.When timing pin moves freely, tighten 3 bolts
to 25 Nm.
7.Remove timing pinLRT-12-045and
flywheel/drive plate locking toolLRT-12-044.
8.Rotate crankshaft twice in a clockwise direction
using crankshaft pulley bolt until flywheel/drive
plate locking toolLRT-12-044can be refitted.
9.Slacken timing belt tensioner securing bolt and
re-tension timing belt.
10.Tighten tensioner bolt to 45 Nm.
11.Fit timing pinLRT-12-045into fuel injection
pump gear hub plate and pump hub. If timing
pin cannot be inserted, slacken injection pump
gear bolts, rotate pump shaft using shaft nut
until pin slides easily into pump hub, Tighten
bolts to 25 Nm.
12.Tighten camshaft gear bolt to 80 Nm.
13.Remove timing pin and flywheel/drive plate
locking tools.
14.Fit plug to flywheel housing, tighten to 12 Nm.
15.Remove crankshaft pulley bolt.
16.Support timing belt front cover on suitable
blocks of wood.
17.Smear a new crankshaft oil seal with engine
oil.
18.Using toolLRT-12-077,fit oil seal from inside
face of front cover.
19.Fit a dry, new gasket to timing belt rear cover.
20.Position timing belt front cover to rear cover.
21.Fit bolts of the correct length in positions
shown.

ENGINE
OVERHAUL47
Sump - refit
1.Clean sump and remove all traces of sealant
using solvent from kit GUG 705548GM.
2.Apply a 2 mm bead of Hylomar Instant Gasket
302 (black) to sump flange ensuring that
sealant is applied inboard of bolt holes.
3.Position sump to cylinder block.
CAUTION: Sump must be fitted within 30
minutes of applying sealant.
4.Fit 22 sump bolts and tighten in sequence
shown to 25 Nm.
5.Check that sump drain plug is tightened to 35
Nm.FLYWHEEL AND STARTER RING GEAR
Flywheel - remove
1.Screw 2 slave 8 mm bolts into flywheel.

ENGINE
48
OVERHAUL
2.Temporarily fit crankshaft pulley.
3.Position toolLRT-12-080to crankshaft pulley,
secure with 4 bolts.
4.Restrain crankshaft pulley using tool
LRT-12-080and remove 8 bolts securing
flywheel; discard locking plate - if fitted.
5.Using assistance, remove flywheel using 2
slave bolts.
NOTE: Dowel located.

ENGINE
50
OVERHAUL
5.Position ring gear to flywheel with square edge
of teeth towards flywheel flange.
6.Press ring gear on to flywheel, allow to air cool.Flywheel - refit
1.Ensure bolt holes in crankshaft are clean and
dry.
2.Ensure 2 slave 8 mm bolts are screwed fully
into flywheel.
3.Using assistance, position flywheel on
crankshaft.
NOTE: Dowel located.
4.Fit and finger tighten 8 bolts.
5.Restrain crankshaft using toolLRT-12-080
and tighten flywheel bolts by diagonal selection
to 146 Nm.
6.Remove toolLRT-12-080and crankshaft
pulley.
7.Remove slave bolts from flywheel.