1995 LAND ROVER DISCOVERY check oil

Tdi
1
FAULT DIAGNOSIS ENGINE OVERHEATING
Before conducting any cooling system diagnosis:
See
Description and operation, Engine Cooling
1.Is coolant level correct?
NO - Allow engine to cool, top up level to
expansion tank seam.
YES - Continue.
2.Is drive belt tension correct?
NO -
See ENGINE, Repair, Compressor
Drive Belt
YES - Continue.
3.Is coolant in radiator frozen?
YES - Slowly thaw and drain system.
See
Adjustment, Coolant
NO - Continue.
4.Is air flow through radiator restricted or blocked?
YES - Apply air pressure from engine side of
radiator to clear obstruction.
NO - Continue.
5.Are there any external leaks, from water pump,
engine gaskets, fast idle thermostat or the heater
unit?
YES - Investigate and rectify.
See Adjustment,
Coolant
NO - Continue.
6.Are fan blades fitted correct way round, concave
side towards engine?
NO - Rectify.
YES - Continue
7.Is viscous unit operating correctly?
See
Description and operation, Viscous Fan
NO - Renew.See Repair, Viscous
Coupling, Fan Blades, Pulley and Fan
Cowl
YES - Carry out a pressure test on radiator cap
and system. Check thermostat type,
operation and correct fitting.
See Repair,
Thermostat
If pressure test leads you to suspect coolant
leakage across gaskets, go to check 10,
otherwise: Continue.8.Are the air conditioning fans operating correctly?
See Electrical Trouble Shooting Manual.
NO - Rectify.
YES - Continue.
9.Is temperature sender and gauge giving
accurate readings?
NO - Sustitute parts and compare readings.
YES - Continue.
10.Carry out cylinder pressure test to determine if
pressure is leaking into cooling system causing
over pressurising and loss of coolant.
If problem is not diagnosed, check the coolant system
for engine oil contamination and engine lubrication
system for coolant contamination.
If only the coolant system is contaminated suspect a
cylinder head gasket.
If both systems are contaminated, suspect the
radiator.
If only the lubrication system is contaminated with
coolant, suspect leakage past cylinder liner seals or
cylinder head gasket.

26COOLING SYSTEM
2
REPAIR WATER PUMP
Service repair no - 26.50.01
Remove
WARNING: Disconnect battery negative
terminal to prevent engine being started
before removing drive belts.
1.Drain engine cooling system.
See Adjustment,
Coolant
2.Remove top hose radiator to thermostat.
3.Remove top hose intercooler to induction
manifold.
4.Slacken water pump and power steering pump
pully retaining bolts.
5.Remove drive belt.
6.Remove centre nut from belt tensioner.
7.Manoeuvre pulley upwards and withdraw
tensioner from retaining stud.
8.Disconnect hose thermostat to bottom hose,
release hose from clip on water pump and move
aside.
9.Remove water pump pulley.
10.Remove power steering pump pulley.
11.Remove 8 bolts securing water pump, noting
location of 3 through bolts.
12.Withdraw pump and gasket, clean all gasket
material from mating surfaces.
Refit
13.Refit water pump in reverse order to removal
using new gasket.RADIATOR
Service repair no - 26.40.01
Remove
1.Drain cooling system.
See Adjustment,
Coolant
2.Disconnect radiator top hose.
3.Remove fan blade assembly.
4.Remove cowl.
5.Disconnect engine oil cooler connections and
turbo intercooler connections from radiator ends.
NOTE: Oil spillage will occur when
connections are loosened. Blank off
exposed oil connections.
6.Disconnect expansion tank bleed hose from
radiator.
7.Remove radiator securing brackets from each
side.
8.Remove radiator unit by lifting from its location.
Check condition of rubber mounting pads.
Refit
9.Check radiator sealing strips are securely
located.
10.Transfer oil cooler adaptors if fitting new radiator.
11.Reverse removal procedure. Tighten oil cooler
connections to
30 Nmbefore fitting fan blades
and cowl.
12.Check all connections for leaks.

V8i
1
FAULT DIAGNOSIS ENGINE OVERHEATING
Before conducting any cooling system diagnosis:
See
Description and operation, Engine Cooling
1.Is coolant level correct?
NO - Allow engine to cool, top up level to
expansion tank seam.
YES - Continue.
2.Is drive belt tension correct?
NO -
See ENGINE, Repair, Drive Belt -
Check Tension
YES - Continue.
3.Is ignition timing correct?
NO -
See ELECTRICAL, Adjustment,
Ignition Timing
YES - Continue.
4.Is coolant in radiator frozen?
YES - Slowly thaw and drain system.
See
Adjustment, Coolant Requirements
NO - Continue.
5.Is air flow through radiator restricted or blocked?
YES - Apply air pressure from engine side of
radiator to clear obstruction.
NO - Continue.
6.Are there any external leaks, from water pump,
engine gaskets or the heater unit?
YES - Investigate and rectify.
See Adjustment,
Coolant Requirements
NO - Continue.
7.Are fan blades fitted correct way round, concave
side towards engine?
NO - Rectify.
YES - Continue.8.Is viscous unit operating correctly?
See
Description and operation, Viscous Fan
NO - Renew.See Repair, Viscous
Coupling, Fan Blades, Pulley and Fan
Cowl
YES - Carry out a pressure test on radiator cap
and system. Check thermostat type,
operation and correct fitting
See Repair,
Thermostat
If pressure test leads you to suspect coolant
leakage across gaskets, go to check 11,
otherwise: Continue.
9.Are the air conditioning fans operating correctly?
See Electrical Trouble Shooting Manual.K5
NO - Rectify.
YES - Continue.
10.Is temperature sender and gauge giving
accurate readings?
NO - Substitute parts and compare readings.
YES - Continue.
11.Carry out cylinder pressure test to determine if
pressure is leaking into cooling system causing
over pressurising and loss of coolant.
If problem is not diagnosed, check the coolant system
for engine oil contamination and engine lubrication
system for coolant contamination.
If the coolant only, or both systems are contaminated,
suspect cylinder head gaskets or radiator.
If only the lubrication stystem is contaminated with
coolant, suspect inlet manifold or front cover gaskets.

26COOLING SYSTEM
4
REPAIR RADIATOR
Service repair no - 26.40.01
Remove
1.Drain cooling system.
See Adjustment,
Coolant
2.Remove viscous coupling and fan assembly.
See Viscous Coupling, Fan Blades, Pulley
and Fan Cowl
3.Release 2 clips and remove fan cowl.
4.Disconnect radiator top hoses.
5.Disconnect four transmission and engine oil
cooler connections to radiator end tanks. Note oil
spillage will occur when connections are
loosened. Blank off exposed oil connections.
6.Disconnect transmission oil temperature sensor.
7.Remove radiator securing brackets from each
side.
8.Remove radiator unit by lifting from its location.
Check condition of rubber mounting pads.Refit
9.Reverse removal procedure.
10.Clean unions and apply sealant.
11.Lubricate new 'O' rings before fitting.
12.Check radiator sealing strips are securely
located.
13.Transfer oil cooler adaptors if fitting new radiator.
14.Ensure that oil cooler connections are tightened
to
30 Nm.before fitting fan blades and cowl.
15.Clean coolant/oil spillage from vehicle.
16.Check all connections for coolant/oil leaks.

V8i
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Oil cooler pipes 30..........................................................................................
Radiator filler plug (plastic) 6.........................................................................

30MANIFOLD AND EXHAUST SYSTEM
4
REPAIR EXHAUST MANIFOLD - Tdi
Service repair no - 30.15.10
Remove
1.Disconnect battery negative lead.
2.Remove heat shield from rear of air intake
manifold.
3.Release dip stick tube from cylinder block.
4.Disconnect the intake hose from the manifold.
5.Remove the two bolts and two nuts securing the
intake manifold to the cylinder head and
withdraw the inlet manifold.
6.Remove air filter inlet pipe to turbo unit.
7.Remove intercooler pipe from turbo to
intercooler.
8.Disconnect the EGR pipe from the inlet manifold
hose.
9.Remove the three fixings at the exhaust pipe
flange.
10.Release the turbo charger oil pipes from the
cylinder block.
11.Remove the turbo boost pipes.
12.Remove seven bolts securing the exhaust
manifold, release the heater rail and remove the
manifold gasket, complete with turbo unit.
13.Remove four bolts and disconnect diaphragm
rod from manifold, and remove turbo charger if
necessary.
Refit
14.Reverse removal procedure. 1 to 12. Use a new
manifold and exhaust flange gaskets.
15.Reconnect battery negative lead. Start engine
and check for leaks.

33CLUTCH
2
FAULT DIAGNOSIS FAULT/SYMPTOM CHART
Symptoms
Slip Spin/Drag Judder/Fierce Fault Item
* * * Worn or oil on clutch linings 2
* * * Mechanical damage45678
* * Distorted clutch plate 2
* Failed or air in hydraulic system 12 13
* * Primary shaft tight fit in crankshaft bush 15 17
* Clutch splines sticking 2 15
* Weak clutch plate springs or insecure/worn
engine/gearbox mountings6
* Insecure/worn propeller shafts
* Insecure/worn suspension components/rubber
bushes
For items refered to in this chart.See Description and operation, Description
CLUTCH NOISE - MECHANICAL FAULTS
Noise from clutch or gearbox in neutral, which
disappears when clutch is depressed.
Suspect gearbox input/primary shaft bearings.
See MANUAL GEARBOX, Fault diagnosis,
Manual Gearbox
- Noise from gearbox in neutral, which
disappears when clutch is depressed
Noise from clutch or gearbox in neutral, which
changes tone or becomes worse when the clutch
is depressed.
Suspect worn release bearing.
Knocking/rattling from clutch or gearbox in
neutral, which is reduced or disappears when the
clutch is depressed.
Suspect worn/weak release lever retainer or
clutch unit.
Noise from clutch or gearbox in neutral, which
disappears when clutch is depressed.
Suspect gearbox fault.
See MANUAL GEARBOX, Fault diagnosis,
Manual Gearbox
- Noise from gearbox in neutral, which
disappears when clutch is depressed.HYDRAULIC FAULTS
Unable to dis-engage clutch, little or no pedal
resistance.
1.Check condition, specification and level of fluid.
2.Check pipes and cylinders for leaks.
3.Check that air vent in reservoir lid is clear.
Suspect faulty master cylinder if no fluid leaks
present.
See Repair, Master Cylinder
Spongy pedal operation
1.Check condition, specification and level of fluid.
2.Check that air vent in reservoir lid is clear.
Suspect air in fluid.
See Repair, Bleed Hydraulic System
Clutch is difficult to dis-engage and/or does not
immediately re-engage when pedal is released.
1.Check condition, specification and level of fluid.
2.Check that air vent in reservoir lid is clear.
Suspect pedal pivot, master cylinder or slave
cylinder seizure.
See Repair, Master Cylinder

R380
3
REPAIR Assembling transfer gearbox to main gearbox
45.Clean extension housing and transfer gearbox
mating faces.
46.Ensuring loose upper dowel is fitted, hoist
transfer gearbox into position.
47.Fit and tighten nut and bolts to
34Nm.
48.Connect high/low operating rod, fit and tighten
locknut.
49.Fit link to differential lock lever and secure with 2
clips
50.Align lever to high/low shaft, position washer, fit
bolt and new Nyloc nut. Tighten to
2Nm.
51.Position breather pipes, secure pipe unions
using new sealing washers. Tighten unions to
15Nm.
Fitting transfer gearbox and main gearbox
assembly to engine
52.Position transmission assembly to hoist cradle.
53.Clean bell housing and engine mating faces.
54.Temporarily fit gear lever and select any gear in
main gearbox to facilitate entry of gearbox input
shaft.
55.Position and raise hoist, and fit transmission to
engine whilst keeping wires and pipes clear to
prevent trapping.
56.Fit and tighten nuts securing transmission to
engine.
57.Connect reverse lamp switch connectors and
differential lock switch connectors.
58.Secure breather pipes to harness with clips.
59.Position temporary support.
60.Remove 2 bolts securing lifting cradle to
transmission and remove hoist. Apply Loctite
290 to bolts and refit bolts.
61.Position cross-member, loosely fit nuts and bolts
securing cross-member mountings to
transmission.62.Raise transmission, align cross-member and
loosely fit nuts and bolts securing cross-member
to chassis.
63.Tighten all securing nuts and bolts. Remove
supporting jack from under sump.
64.Remove temporary support.
65.Fit handbrake cable through transmission tunnel
and secure gaiter.
66.Connect speedometer cable to transfer gearbox.
67.Line up marks and connect front and rear
propeller shafts.
68.Clean spacer, clutch slave cylinder and gearbox
mating faces.
69.Position spacer and slave cylinder, fit bolts.
Tighten to
25Nm.
70.Untie intermediate exhaust pipe(s) and refit
exhaust front pipe(s).
See MANIFOLD AND
EXHAUST SYSTEM, Repair, Exhaust System
Complete
71.Refill main gearbox and transfer gearbox with oil.
See SECTION 10, Maintenance, Under
Vehicle Maintenance
72.Lower ramp [hoist].
73.Fit fan cowl, fit and tighten bolts.
74.Align breather pipe clip to cylinder block, fit and
tighten bolts.
75.Fit handbrake cable adjuster and secure with 'C'
clip.
76.Align cable trunnion to handbrake lever, fit clevis
pin and secure with clip.
77.Check handbrake adjustment.
See SECTION
10, Maintenance, Vehicle Interior
78.Fit upper gear lever, fit and tighten bolt.
79.Fit gear selector lever and high/low selector
lever draft excluders.
80.Position draft excluder clamp rings, fit and
tighten screws.
81.Refit sound insulation.
82.Refit centre console.
See CHASSIS AND
BODY, Repair, Centre Console
83.Connect battery earth lead.