1995 LAND ROVER DISCOVERY clock

12ENGINE
18
REPAIR 10.Apply sealant to flywheel housing mating face on
cylinder block (Fig. J5944).
11.Fit housing to cylinder block and secure with
bolts as removed. Tighten to
45 Nm.
12.Remove surplus sealant from block.
13.Refit starter motor.
14.Refit flywheel.
See Flywheel
15.Refit clutch.See CLUTCH, Repair, Clutch
Assembly
16.Refit gearbox.See MANUAL GEARBOX,
Repair, R380 Manual Gearbox
17.Reconnect battery negative lead.OIL FILTER
Service repair no - 12.60.01
Remove
1.Place drain tray under filter.
2.Unscrew filter anti-clockwise, using a strap or
spanner.
Refit
3.Smear clean engine oil on seal of new filter.
4.Screw on filter until sealing ring touches
machined face, then tighten a further half turn by
hand only. Do not over tighten.

V8i
1
REPAIR DRIVE BELT
A single 'serpentine drive belt' is introduced for 1995
model year. This belt drives the water pump and all
the ancilliaries. It is essential that the belt is fitted
exactly as shown in illustrations RR3956 and RR3957.
It should also be noted that the water pump/viscous
fan is driven in a counter clockwise direction.
A drive belt tensioner automatically tensions the drive
belt, eliminating the need for tensioning individual
drive belts. Turning the tensioner pulley in a clockwise
direction will release drive belt tension.
Under normal highway use the belt must be changed
at 120,000 kilometres, 75,000 miles or five years
whichever occurs first.
The drive belt must be examined at every service and
replaced if necessary.
Off road driving
Regular examination of the drive belt is essential if the
vehicle is used off road. The vehicle driver should be
requested to identify the type of mileage the vehicle
has covered.
After every off road session the owner should inspect
the belt for cuts and possible damage caused by
stones. If belt has jumped, reposition belt correctly. A
new belt must be fitted at the next service or before,
dependant on the type of damage sustained.
Fan cowl
To ensure easy access to the drive belt the top portion
of the fan cowl is detachable.
Check condition
Check condition of drive belt. Renew a belt that shows
signs of wear, splitting or oil contamination.DRIVE BELT RENEW
Service repair no - 86.10.03
Air conditioning
Non air conditioning

12ENGINE
2
REPAIR Remove
1.Remove fan cowl upper.
2.Release drive belt tension by turning tensioner
clockwise.
3.With tension released, remove belt from
generator pulley.
4.Release tensioner pulley.
5.Remove drive belt. Mark direction of rotation on
belt if refitting
Refit
6.Clean drive belt pulley grooves and ensure
grooves are not damaged.
7.Position belt correctly around all pulleys except
generator. Illustrations RR3956 and RR3957
show correct drive belt run.
8.Turn drive belt tensioner clockwise.
9.Locate drive belt on generator pulley.
10.Ensure drive belt is squarely located on pulleys
with all grooves engaged.
11.Release tensioner to tension drive belt.
12.Fit upper fan cowl section.DRIVE BELT - CHECK TENSION
As the drive belt is automatically tensioned, no tension
check or adjustment should be necessary. If the drive
belt is believed to be slack carry out the following
checks:
1.Visually check drive belt tension.
2.Watch movement of tensioner with engine
running, 5 mm 'bounce' is normal. If tensioner
movement is 12 mm or more, fit a new tensioner.
See Drive Belt Tensioner
3.Inspect tensioner. Is the tensioner arm and
spring case in contact? If so fit a new tensioner.
4.Using a recognised drive belt tensioning gauge,
check belt tension several times, running engine
between checks. The checks should be made at
the same point on the belt, away from the
tensioner.
Drive belt tension, with used tensioner and used drive
belt should be more than:-
270N. Non air conditioning or
295N with air conditioning.

12ENGINE
22
REPAIR
CAUTION: Ease timing belt off gears using
fingers only. Metal levers may damage the
belt and gears. Do not rotate engine with
timing belt removed and cylinder head fitted.
Timing belts must be stored and handled with
care. Always store a timing belt on its edge with a
bend radius greater than 50 mm. Do not use a
timing belt which has been twisted or bent double
as this can fracture reinforcing fibres. Do not use
an oil contaminated timing belt. Although the belt
has a service life of 96,000 miles, 160,000 km, an
existing belt should only be refitted if it has
completed less than 48,000 miles, 80,000 km.
Refit
NOTE: For torque values.See
Specifications, torque, Torque values
1.Clean timing belt gears and pulleys.
2.Clean crankshaft pulley.
CAUTION: If original belt is to be refitted,
ensure direction of rotation mark is facing
correct way.
3.Fit timing belt to gears, starting at the crankshaft
gear and working in an anti-clockwise direction.
CAUTION: Ensure the belt run between the
crankshaft and exhaust camshaft gear is
kept taut during the fitting procedure.
4.Fit timing belt lower cover, tighten 3 bolts to the
correct torque.
5.Fit crankshaft pulley to crankshaft timing gear.
6.Fit tool LRT-12-059 to crankshaft pulley, fit 2
bolts to retain tool.
7.Fit crankshaft pulley centre bolt, and using tool
LRT-12-059 to restrain pulley, tighten bolt to the
correct torque.
8.Remove tool LRT-12-059
9.Fit bolts securing crankshaft pulley to timing
gear, tighten bolts to the correct torque.
10.Remove tool LRT-12-060.Tension belt
1.Loosen timing belt tensioner pulley bolt.
2.Apply
40Nmanti-clockwise torque to inlet cam
pulley bolt and release.
3.Tighten tensioner pulley bolt to the correct
torque.
4.Remove tool LRT-12-058 from flywheel.
5.Fit timing belt centre cover, tighten 5 bolts to the
correct torque.
6.Fit timing belt upper cover, tighten 5 bolts to the
correct torque.
7.Fit drive belt.

19FUEL SYSTEM
2
ADJUSTMENT LOW AND HIGH IDLE SPEED
Adjust
The high idle speed (cold start idle) is
automatically set by the setting of the low idle
speed and can not be adjusted individually.
1.Check and adjust throttle cable.
2.Start engine and run it until normal operating
temperature is reached.
3.Using a suitable tachometer, check the engine
idle speed.
See ENGINE TUNING DATA,
Information, 300 Tdi Engine
4.If adjustment is necessary, loosen the locknut on
the injector pump.
5.Turn the adjustment screw either clockwise to
increase the engine speed or anti-clockwise to
decrease the speed. Run the engine at an
increased speed for a few seconds then check
the idle speed again.
6.When the correct speed has been achieved,
hold the adjuster screw steady while tightening
the locknut.
NOTE: The low idle speed control is the
only permitted adjustment in service. Any
additional adjustments required must be
entrusted to authorised Bosch agents.CHECK TURBOCHARGER BOOST PRESSURE
For boost pressure.
See ENGINE TUNING DATA,
Information, 300 Tdi Engine
1.Disconnect, from turbocharger, hose to actuator.
Insert into a suitable "T" piece.
2.Connect a short length of suitable hose to
turbocharger and connect other end to "T" piece.
3.Connect a further length of hose to third leg of
the "T" piece and other end to a pressure gauge
capable of reading in excess of 61 cm Hg. The
pressure gauge hose must be capable of
reaching passenger compartment so that gauge
may be observed.
4.To check maximum boost pressure, drive
vehicle normally but in such a manner that full
throttle can be maintained whilst climbing a hill
with engine speed held steady between 2,500
and 3,000 rev/min.

Tdi
11
REPAIR FUEL INJECTION PUMP AND TIMING
Service repair no - 19.30.07
NOTE: The following text refers to a Tdi
vehicle with a manual gearbox without
electronic diesel control. Where reference
is made to the timing tool substitute the following
information for automatic and EDC variants.
If manual gearbox:Timing tool LRT-12-044 fits into
the base of the flywheel housing
If manual gearbox with EDC:Timing tool
LRT-12-085 must be used and also fits into the base
of the flywheel housing.
If automatic gearbox:Timing tool LRT-12-044 fits
into the larger bolt hole of coverplate on engine
backplate, sited near to the rear of sump. Pin locates
in ring gear.
Remove
1.Disconnect battery negative lead.
2.Remove injection pipes, pump to injector.
3.Remove oil filler cap from rocker cover.
4.Viewing valve mechanism through filler aperture,
turn crankshaft clockwise until No. 1 cylinder is
just before TDC.
5.Refit oil filler cap.
6.Remove blanking plug from flywheel housing.
7.Fit timing tool LRT-12-044 to flywheel housing,
do not engage centre pin.
8.Continue rotating crankshaft clockwise until
centre pin engages with timing slot in flywheel.
9.Remove injection pump access plate, complete
with gasket, from front cover plate.
10.Fit pin from LRT-12-045 to injection pump gear.
11.Remove drive gear to pump hub fixing bolts and
plate.

19FUEL SYSTEM
2
FAULT DIAGNOSIS BASE IDLE SPEED SETTING
NOTE: Base idle speed is set at factory. It
should not require further adjustment
unless plenum chamber is changed. The
adjustment screw is sealed with a plug to prevent
unauthorised alteration. Check ignition timing
before attempting following procedure, since this
will affect idle speed.
Equipment required
Two blanking hoses.these are manufactured using
a new air by-pass valve hose - Part No.ETC7874. Cut
two equal pieces 90mm long from hose and seal one
end of each, using 13mm diameter bar. Use a suitable
clamp to ensure an air tight seal.
Checking procedure
1.Drive vehicle at least two miles until engine and
transmission are hot. Switch off engine.
2.Check all electrical loads are OFF, including air
conditioning.
3.Remove air by-pass valve hose.
4.Fit blanking hoses to both plenum chamber and
air by-pass valve. Ensure hoses are securely
fitted to prevent air leaks. Note throttle cable and
cruise control actuator have been omitted from
illustration.5.Start engine and check idle speed is within
limits.
See ENGINE TUNING DATA,
Information, Engine 3.9 v8i
Adjusting base idle speed
6.Drill tamper proof plug and insert a self tapping
screw to enable plug to be extracted.
7.Start engine, adjust idle screw clockwise to
decrease or counter-clockwise to increase idle
speed.
8.Stop engine, remove blanking hoses. Reconnect
hose to plenum.
9.Fit new tamper proof plug.

Tdi
1
REPAIR VISCOUS COUPLING, FAN BLADES, PULLEY AND
FAN COWL
Service repair no - 26.25.03/05
Viscous coupling -Remove1to3
Fan blades -Remove1to4
Fan cowl -Remove1to3
Fan pulley -Remove1to6
Remove
WARNING: Disconnect battery negative
terminal to prevent engine being started
before removing or adjusting drive belt.
1.Slacken nut securing viscous coupling/fan blade
assembly to pulley.
NOTE: Nut securing viscous unit to pulley
has a left hand thread. Release by turning
clockwise when viewed from front of
viscous unit.
2.Drop viscous unit and fan assembly into bottom
of cowling
3.Remove two fixings clips from top of cowling and
lift cowling complete with viscous unit and fan
out of lower mountings.
4.Remove fan blades from viscous coupling if
necessary.
5.Remove serpentine drive belt and, if fitted, air
conditioning compressor belt.
6.Remove pulley fixings, remove pulley.
NOTE: The serpentine belt is removed by
using a hexagonal socket and tommy bar
on the auto-tensioning pulley nut. Whilst
tensioning the device the belt can be removed.
7.Reverse removal procedure. Ensure fan blades
are fitted correctly. Fan is marked 'front' and
should be fitted with word 'front' closest to
radiator. Tighten to
30 Nm.
8.Refit drive belt.See ENGINE, Repair, Drive
Belt
THERMOSTAT
Service repair no - 26.45.01
Remove
1.Partially drain cooling system, until coolant level
is below thermostat housing.
2.Disconnect hose from thermostat housing.
3.Disconnect electrical connections to water
temperature switch.
4.Remove outlet elbow.
5.Withdraw thermostat.
Test
6.Note rating of thermostat is 88°C. Place
thermostat in a container half full of water. Heat
water, observe temperature at which thermostat
begins to open. Thermostat is satisfactory if its
open between 85°C and 89°C.
Refit
7.Insert thermostat with jiggle pin/vent hole upper
most (12 o'clock position) .
8.Fit the outlet elbow and new joint washer.
Tighten to
28 Nm.
9.Reverse removal procedure. 1 to 3.
10.Check for coolant leaks around all connections
and joint faces.