1995 JEEP YJ auxiliary battery

(5) Be sure that the air conditioner (if equipped) is
turned off.
WARNING: USE EXTREME CAUTION WHEN THE
ENGINE IS OPERATING. DO NOT STAND IN A DI-
RECT LINE WITH THE FAN. DO NOT PUT YOUR
HANDS NEAR THE PULLEYS, BELTS OR FAN. DO
NOT WEAR LOOSE CLOTHING.
(6) Start the engine and operate at 2400 rpm.
Within ten minutes the air temperature (indicated on
the dial thermometer) should be up to 88É C (190É F).
Fan driveengagementshould have started to occur
at between 74É to 82É C (165É to 180É F). Engage-
ment is distinguishable by a definiteincreasein fan
flow noise (roaring). The timing light also will indi-
cate an increase in the speed of the fan.
(7) When the air temperature reaches 88É C (190É
F), remove the plastic sheet. Fan drivedisengage-
mentshould have started to occur at between 57É to
79É C (135É to 175É F). A definitedecreaseof fan
flow noise (roaring) should be noticed. If not, replace
the defective viscous fan drive unit.
VISCOUS FAN DRIVE REMOVAL/INSTALLATION
Refer to the previous section on Cooling System
Fan for removal and installation procedures of the
viscous drive unit.
Viscous Fan Drive Fluid Pump Out Require-
ment:After installing anewviscous fan drive, bring
the engine speed up to approximately 2000 rpm and
hold for approximately two minutes. This will ensure
proper fluid distribution within the drive.
AUXILIARY ELECTRIC COOLING FANÐXJ MODELS
WITH 4.0L 6-CYLINDER ENGINE
OPERATION
XJ models equipped with a 4.0L 6-cylinder engine
may also have an auxiliary electrical cooling fan.
This is with models that have air conditioning and/or
heavy duty cooling. The fan is controlled by the cool-
ing fan relay, which is located in the power distribu-
tion center (PDC). For the location of relay within
the PDC (Fig. 41), refer to the label on PDC cover.
When coolant temperature is above 88ÉC (190ÉF),
the powertrain control module (PCM) provides a
ground path for the fan relay. This ground is pro-
vided through pin/connector #31 of the PCM 60-way
connector. Battery voltage is then applied to the fan
through the relay. When coolant temperature is be-
low 88ÉC (190ÉF), the PCM opens the ground path to
the relay. This will prevent the cooling fan from be-
ing energized.
Whenever the air conditioning is operated, the
PCM engages the auxiliary cooling fan. It provides aground path to the cooling fan relay. This ground is
provided through pin/connector #31 of the PCM 60-
way connector.
DIAGNOSIS AND RELAY TESTING
The powertrain control module (PCM) will enter a
diagnostic trouble code (DTC) number 35 in memory
if it detects a problem in the auxiliary cooling fan re-
lay or circuit. This will be read as a flashing signal
at the instrument panel mounted Malfunction Indica-
tor Lamp (displayed on the instrument panel as the
CHECK ENGINE lampÐfigure 42). Refer to On-
Board Diagnostics in Group 14, Fuel Systems for in-
formation on accessing a DTC.
The DTC can also be accessed through the DRB
scan tool. Refer to the appropriate Powertrain Diag-
Fig. 41 PDCÐXJ Models
Fig. 42 Check Engine LampÐXJ ModelsÐTypical
JCOOLING SYSTEM SERVICE PROCEDURES 7 - 35

TRAILER HITCH
TRAILER HITCHÐXJ
CLASS III HITCH
A class III weight-distributing/equalizer type hitch
can be used to tow a trailer:
²Having a maximum gross weight of 5,000 lbs/2250
kg.
²Having a maximum tongue weight of 750 lbs/332
kg).
The following vehicle basic equipment is required
for class III trailer towing:
²P205/75R15 or larger tires.
²Full size spare tire.
²Trailer sway control.
²Trailer tow wire harness and connector.
²Heavy duty turn signal flasher element.
²Heavy duty axle (with synthetic lubricant).
²Heavy duty cooling system.
²Heavy duty generator/battery.
²Auxiliary automatic transmission fluid cooler.
²I-6, 4.0L engine.
Wide-angle type door mirrors are recommended but
not required.
WIRE HARNESS CONNECTORS
CLASS I HITCH CONNECTOR
The trailer tow wire harness connector for class I
trailer hitches is a 5-terminal, in-line type connector.
Terminal 5 is the source for vehicle ground (Fig. 1)
CLASS III HITCH CONNECTOR
The trailer tow wire harness connector for class III
trailer-tow hitches is a 7-terminal, circular type con-
nector (Fig. 2).
The 12-volt circuit for the trailer is protected
from overloads. A auto-reset type circuit
breaker is located in the trailer tow wire har-
ness near the plug-in relays.
CAUTION: The trailer tow wire harness package
does not include a vehicle battery isolator unit. Be-
cause of this, the trailer battery can totally dis-
charge the vehicle battery if the engine is not
operated for an extended period of time.
A blue wire (without a connector) located under in-
strument panel near fuse panel is available for
trailer electric brake control unit.
Fig. 1 Trailer Tow Wire Harness Connectors
JTRAILER HITCH 23 - 77

ANTENNA........................8F-2,8F-5
ANTENNA, POWER; RADIO (XJ-RHD) . . . 8W-47-1
ANTENNA REMOVE/INSTALL - XJ.........8F-8
ANTENNA REMOVE/INSTALL - YJ........8F-10
ANTILOCK BRAKES (ABS)................5-1
ANTILOCK BRAKING MODE, ABS
OPERATION IN.......................5-36
ANTILOCK ECU AND HCU DIAGNOSIS......5-3
APPLICATION CHARTS, GEARTRAIN
OPERATION........................21-169
APPLICATION, TRANSMISSION..........21-67
APPLICATIONÐXJ VEHICLES, BULB......8L-18
APPLICATIONÐYJ VEHICLES, BULB......8L-32
APPLIQUEÐXJ, QUARTER WINDOW.....23-25
APPLIQUEÐYJ, RADIATOR GRILLE.....23-104
APRONSÐYJ, FENDER SPLASH........23-115
ARM, LOWER SUSPENSION.............2-13
ARM, PITMAN..................19-17,19-20
ARM REMOVE/INSTALL, LIFTGATE
WIPER.............................8K-17
ARM REMOVE/INSTALL, WINDSHIELD
WIPER.............................8K-17
ARM, UPPER SUSPENSION.............2-12
ARMING/DISARMING MECHANISM;
RESTRAINT SYSTEMS.................8M-2
ARMING/DISARMING MECHANISM;
STEERING..........................19-48
ARMS AND PUSH RODS, ROCKER....9-23,9-65
ASH RECEIVER TRAY LAMPÐXJ, I/P.....23-80
ASSEMBLY....................19-63,19-71
ASSEMBLY AND ADJUSTMENT, VALVE
BODY.............................21-153
ASSEMBLY, CALIPER...................5-50
ASSEMBLY, COMPRESSOR CLUTCH......24-20
ASSEMBLY, DIFFERENTIAL; FRONT
SUSPENSION AND AXLE................2-38
ASSEMBLY, DIFFERENTIAL; REAR
SUSPENSION AND AXLES...............3-21
ASSEMBLY, FINAL; FRONT SUSPENSION
AND AXLE...........................2-46
ASSEMBLY, FINAL; REAR SUSPENSION
AND AXLES..........................3-29
ASSEMBLY, FUEL RAIL................14-62
ASSEMBLY, GEAR....................19-43
ASSEMBLY, IMPACT SENSOR/INFLATOR . . . 8M-2
ASSEMBLY, PINION MEASUREMENT.......3-22
ASSEMBLY REMOVE/INSTALL, CLUSTER . . 8E-17,
8E-35
ASSEMBLY REPLACEMENT, ADJUSTER
PLUG..............................19-29
ASSEMBLY REPLACEMENT, COLUMN.....19-52
ASSEMBLY REPLACEMENTÐXJ
VEHICLES, DRIVE AXLE; FRONT
SUSPENSION AND AXLE................2-23
ASSEMBLY REPLACEMENTÐXJ
VEHICLES, DRIVE AXLE; REAR
SUSPENSION AND AXLES...........3-14,3-31
ASSEMBLY REPLACEMENTÐYJ
VEHICLES, DRIVE AXLE; FRONT
SUSPENSION AND AXLE................2-24
ASSEMBLY REPLACEMENTÐYJ
VEHICLES, DRIVE AXLE; REAR
SUSPENSION AND AXLES...............3-14
ASSEMBLY (SHORT BLOCK), SERVICE
ENGINE..............................9-4
ASSEMBLY TIPS, TRANSMISSION......21-155
ASSEMBLY, TRANSFER CASE
....21-294,21-319
ASSEMBLY/INSTALLATION, PINION GEAR
. . 2-42
ASSEMBLYÐXJ VEHICLES, ENGINE
. . . 9-18,9-59
ASSEMBLYÐYJ VEHICLES, ENGINE
. . . 9-20,9-62
ASSIST HANDLEÐXJ
.................23-89
ASSIST HANDLEÐYJ, FULL-METAL
DOOR
............................23-136
AUTO SHUTDOWN (ASD) RELAYÐPCM
OUTPUT
............................14-26
AUTOMATIC BELT TENSIONERÐXJ
MODELS WITH RIGHT HAND DRIVE
.......7-42
AUTOMATIC SHUT DOWN (ASD) RELAY;
FUEL/IGNITION (XJ)
................8W-30-1
AUTOMATIC SHUT DOWN (ASD) RELAY;
FUEL/IGNITION (YJ)
................8W-30-1
AUTOMATIC SHUT DOWN (ASD) RELAY;
FUEL/IGNITION (XJ-RHD)
............8W-30-1
AUTOMATIC SHUTDOWN (ASD) RELAY;
FUEL SYSTEM
.......................14-59
AUTOMATIC SHUTDOWN (ASD) RELAY;
IGNITION SYSTEMS
..............8D-17,8D-1AUTOMATIC SHUTDOWN (ASD) RELAY
TEST...............................8D-6
AUTOMATIC SHUTDOWN (ASD) RELAY
TESTING...........................14-46
AUTOMATIC SHUTDOWN (ASD)
SENSEÐPCM INPUT..................14-21
AUTOMATIC TRANSMISSION............0-23
AUTOMATIC TRANSMISSION, 30RH/
32RH..............................21-67
AUTOMATIC TRANSMISSION, AW-4.....21-165
AUTOMATIC TRANSMISSION SHIFTER/
IGNITION INTERLOCK MECHANISM......19-55
AUXILIARY ELECTRIC COOLING FANÐXJ
MODELS WITH 4.0L 6-CYLINDER
ENGINE.............................7-35
AW-4 ACCUMULATOR COMPONENT
IDENTIFICATION....................21-342
AW-4 AUTOMATIC TRANSMISSION......21-165
AW-4 BUSHING AND PISTON
CLEARANCE........................21-339
AW-4 CLUTCH AND BRAKE PACK
REQUIREMENTS....................21-341
AW-4 CLUTCH DISC AND PLATE
THICKNESS........................21-338
AW-4 GENERAL SPECIFICATIONS.......21-337
AW-4 IN-VEHICLE SERVICE............21-182
AW-4 OIL PUMP WEAR LIMITS........21-338
AW-4 RETAINER AND PISTON
SPECIFICATIONS....................21-340
AW-4 TORQUE SPECIFICATIONS........21-344
AW-4 TRANSMISSION DIAGNOSIS......21-176
AW-4 TRANSMISSION OVERHAUL......21-201
AW-4 TRANSMISSION REMOVAL AND
INSTALLATION......................21-198
AW-4 VALVE AND SPRING
IDENTIFICATION....................21-343
AW-4 VALVE BODY CHECK BALL
DIMENSIONS.......................21-341
AWAY, PEDAL FALLS....................5-5
AX 15 MANUAL TRANSMISSION........21-33
AX 4/5 MANUAL TRANSMISSION.........21-1
AXLE (2WD), MODEL 30 AXLE AND
TUBE...............................2-22
AXLE, 8 1/4......................3-30,3-51
AXLE ALIGNMENT, REAR...............3-10
AXLE AND TUBE AXLE (2WD), MODEL
30 .................................2-22
AXLE ASSEMBLY REPLACEMENTÐXJ
VEHICLES, DRIVE; FRONT
SUSPENSION AND AXLE................2-23
AXLE ASSEMBLY REPLACEMENTÐXJ
VEHICLES, DRIVE; REAR SUSPENSION
AND AXLES......................3-14,3-31
AXLE ASSEMBLY REPLACEMENTÐYJ
VEHICLES, DRIVE; FRONT
SUSPENSION AND AXLE................2-24
AXLE ASSEMBLY REPLACEMENTÐYJ
VEHICLES, DRIVE; REAR SUSPENSION
AND AXLES..........................3-14
AXLE BUSHING REPLACEMENT......2-12,2-34
AXLE, FRONT DRIVE....................2-3
AXLE, MODEL 30.....................2-49
AXLE, MODEL 30 FRONT...............2-49
AXLE, MODEL 35.................3-13,3-51
AXLE NOISE/VIBRATION DIAGNOSIS;
FRONT SUSPENSION AND AXLE..........2-18
AXLE NOISE/VIBRATION DIAGNOSIS;
REAR SUSPENSION AND AXLES
..........3-9
AXLE SHAFT
.........................3-16
AXLE SHAFT, HUB BEARING
.............2-25
AXLE SHAFT OIL SEAL REPLACEMENT,
INNER
..............................2-35
AXLE SHAFT SEAL AND BEARING
........3-17
AXLE SHAFT, SEAL AND BEARING
SERVICE
............................3-32
AXLE SPECIFICATIONS; FRONT
SUSPENSION AND AXLE
................2-49
AXLE SPECIFICATIONS; REAR
SUSPENSION AND AXLES
...............3-51
AXLEÐYJ VEHICLES, VACUUM
DISCONNECT
.........................2-27
AXLES
...............................3-1
AXLES, FRONT AND REAR
..............0-24
AXLE/SHIFT MOTOR DIAGNOSIS
(CONT'D), DISCONNECT
................2-30
AXLE/SHIFT MOTOR DIAGNOSIS,
DISCONNECT
.........................2-29BACKLASH AND CONTACT PATTERN
ANALYSIS; FRONT SUSPENSION AND
AXLE...............................2-45
BACKLASH AND CONTACT PATTERN
ANALYSIS; REAR SUSPENSION AND
AXLES..............................3-27
BACK-UP LAMPS; REAR LIGHTING (XJ) . 8W-51-1
BACK-UP LAMPS; REAR LIGHTING
(XJ-RHD).........................8W-51-1
BACK-UP LAMPS; REAR LIGHTING (YJ) . 8W-51-1
BACK-UP/REAR TURN SIGNAL/TAIL
LAMP BULB REPLACEMENTÐXJ........8L-12
BACK-UP/REAR TURN SIGNAL/TAIL
LAMP BULB REPLACEMENTÐYJ........8L-28
BALANCE, TIRE AND WHEEL............22-6
BALL DIMENSIONS, AW-4 VALVE BODY
CHECK............................21-341
BALL STUD REPLACEMENTÐXJ,
LIFTGATE SUPPORT ROD..............23-63
BALL STUDS, STEERING KNUCKLE.......2-32
BAR, STABILIZER; FRONT SUSPENSION
AND AXLE.......................2-11,2-15
BAR, STABILIZER; REAR SUSPENSION
AND AXLES...........................3-5
BAR, TRACK; FRONT SUSPENSION AND
AXLE...........................2-11,2-15
BAR, TRACK; REAR SUSPENSION AND
AXLES...............................3-8
BARÐXJ, SOUND....................23-94
BARÐYJ, SPORT...................23-132
BARRIERÐXJ, CARGO...............23-101
BASE COAT/CLEAR COAT FINISH.........23-158
BATTERY; BATTERY/STARTER/
GENERATOR SERVICE..................8B-1
BATTERY; BATTERY/STARTING/
CHARGING SYSTEMS DIAGNOSTICS......8A-2
BATTERY; LUBRICATION AND
MAINTENANCE.......................0-20
BATTERY CHARGING...................8A-7
BATTERY CHARGING TIME TABLE........8A-8
BATTERY CLASSIFICATIONS AND
RATINGS...........................8A-23
BATTERY DIAGNOSIS..................8A-4
BATTERY FEED; FUEL/IGNITION (XJ) . . . 8W-30-1
BATTERY FEED; FUEL/IGNITION (YJ) . . . 8W-30-2
BATTERY FEED; FUEL/IGNITION
(XJ-RHD).........................8W-30-1
BATTERY RATINGS....................8A-3
BATTERY REMOVE/INSTALL.............8B-1
BATTERY SPECIFICATIONS; BATTERY/
STARTER/GENERATOR SERVICE..........8B-8
BATTERY SPECIFICATIONS; BATTERY/
STARTING/CHARGING SYSTEMS
DIAGNOSTICS.......................8A-23
BATTERY TRAYÐXJ..................23-14
BATTERY TRAYÐYJ.................23-110
BATTERY VOLTAGEÐPCM INPUT........14-21
B/C-PILLAR AND LIFTGATE PILLAR TRIM
COVERSÐXJ........................23-88
BEARING AND AXLE SHAFT, HUB.........2-25
BEARING, AXLE SHAFT SEAL............3-17
BEARING LUBRICANTS, CHASSIS
COMPONENT AND WHEEL..............0-28
BEARING NOISE, GEAR; FRONT
SUSPENSION AND AXLE................2-18
BEARING NOISE, GEAR; REAR
SUSPENSION AND AXLES................3-9
BEARING REPLACEMENT, PILOT..........6-12
BEARING REPLACEMENT, PITMAN
SHAFT SEALS.......................19-34
BEARING REPLACEMENT, RELEASE.......6-11
BEARING SERVICE, AXLE SHAFT, SEAL....3-32
BEARINGS, CRANKSHAFT MAIN......9-45,9-87
BEARINGS, FRONT WHEEL..............0-28
BELT, ACCESSORY DRIVE...............0-21
BELT DIAGNOSIS......................7-38
BELT INDICATOR WARNING LAMP, SEAT;
INSTRUMENT CLUSTER (XJ).........8W-40-2
BELT INDICATOR WARNING LAMP, SEAT;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
BELT SCHEMATICS....................7-38
BELT SERVICEÐEXCEPT RIGHT HAND
DRIVE
..............................7-40
BELT SERVICEÐXJ MODELS WITH
RIGHT HAND DRIVE
...................7-42
BELT SWITCH, DRIVER'S SEAT
......8U-1,8U-3
BELT TENSION, DRIVE
.................7-45
BELT TENSION SPECIFICATIONS
..........7-38
2 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

ENTRY MODULE REMOVE/INSTALL,
KEYLESS...........................8P-10
ENTRY RECEIVER, KEYLESS.............8C-1
ENTRY RECEIVERÐXJ, KEYLESS........23-93
ENTRY TRANSMITTER, KEYLESS . 8P-1,8P-7,8P-8
EQUIPMENT, REFRIGERANT.............24-7
EQUIVALENT VALUES, CONVERSION
FORMULAS.......................Intro.-11
EVACUATING REFRIGERANT SYSTEM.....24-11
EVAP CANISTER..................25-4,25-7
EVAP (EVAPORATION) CONTROL
SYSTEM............................25-4
EVAPORATIVE HOUSING
COMPONENTSÐYJ....................24-6
EVAPORATOR AND HOUSING...........24-35
EVAPORATOR COIL...................24-30
EVAPORATOR/BLOWER HOUSING........24-29
EXHAUST GAS RECIRCULATION (EGR)
SYSTEM............................25-1
EXHAUST GRILLEÐXJ, AIR............23-25
EXHAUST HEAT SHIELDS...............11-1
EXHAUST MANIFOLDÐ2.5L ENGINE,
ENGINE.............................11-7
EXHAUST MANIFOLDÐ4.0L ENGINE,
ENGINE.............................11-7
EXHAUST PIPEÐXJ VEHICLES...........11-3
EXHAUST PIPEÐYJ VEHICLES...........11-4
EXHAUST SYSTEM; EXHAUST SYSTEM
AND INTAKE MANIFOLD................11-1
EXHAUST SYSTEM; LUBRICATION AND
MAINTENANCE.......................0-21
EXHAUST SYSTEM DIAGNOSIS..........11-2
EXHAUST TAILPIPEÐXJ VEHICLES,
MUFFLER............................11-5
EXHAUST TAILPIPEÐYJ VEHICLES,
MUFFLER............................11-6
EXPANSION VALVE..............24-31,24-35
EXTENDED IDLE SWITCH; FUEL/
IGNITION (XJ).....................8W-30-5
EXTENDED IDLE SWITCH TEST..........14-48
EXTENDED IDLE SWITCHÐPCM INPUT . . . 14-23
EXTENSIONÐXJ, QUARTER TRIM PANEL . 23-87
EXTERIOR COMPONENTS.........23-104,23-3
EXTERIOR LAMPSÐXJ................8L-18
EXTERIOR LAMPSÐYJ................8L-32
EXTERIOR MOLDINGSÐXJ, DOOR
WINDOW...........................23-54
EXTERIOR NAMEPLATES (ADHESIVE-
BACKED)ÐYJ......................23-120
EXTERIOR NAMEPLATESÐXJ...........23-26
EXTERNAL HANDLEÐXJ, DOOR.........23-48
EXTERNAL MIRRORSÐXJ.............23-27
EXTERNAL RELEASE HANDLEÐYJ,
FULL-METAL DOOR LATCH............23-140
EXTERNAL SPARE/WHEEL TIRE
CARRIERÐYJ......................23-133
(EXTERNAL)ÐYJ, HALF METAL DOOR
MIRROR..........................23-121
EYE BUSHING REPLACEMENT, LEAF
SPRING; FRONT SUSPENSION AND
AXLE...............................2-17
EYE BUSHING REPLACEMENT, LEAF
SPRING; REAR SUSPENSION AND
AXLES............................3-5,3-7
FAN RELAY AND MOTOR, RADIATOR;
AIR CONDITIONING/HEATER (XJ)......8W-42-2
FAN RELAY AND MOTOR, RADIATOR;
AIR CONDITIONING/HEATER (XJ-RHD) . . 8W-42-2
FAN RELAYÐPCM OUTPUT, RADIATOR . . . 14-28
FANÐXJ MODELS WITH 4.0L
6-CYLINDER ENGINE, AUXILIARY
ELECTRIC COOLING...................7-35
FANS, COOLING SYSTEM...............7-32
FEED, BATTERY; FUEL/IGNITION (XJ) . . . 8W-30-1
FEED, BATTERY; FUEL/IGNITION (YJ) . . . 8W-30-2
FEED, BATTERY; FUEL/IGNITION
(XJ-RHD).........................8W-30-1
FEED, IGNITION; FUEL/IGNITION
(XJ-RHD).........................8W-30-1
FENDER FLAREÐYJ.................23-114
FENDER INNER SPLASH SHIELDSÐYJ . . 23-116
FENDER SPLASH APRONSÐYJ........23-115
FENDERÐXJ, FRONT
.................23-14
FENDERSÐYJ
......................23-110
FIELDÐPCM OUTPUT, GENERATOR
......14-27
FILL LEVEL, TRANSFER CASE
LUBRICANT
........................21-284
FILLER DOOR BUMPERSÐXJ, FUEL
.....23-27FILLER HOSE SPLASH SHIELDÐXJ
VEHICLES, FUEL......................13-4
FILLER NOZZLE/TUBEÐXJ, FUEL........23-26
FILLER PROTECTOR/NOZZLEÐYJ, FUEL . 23-121
FILLER TUBE CAP, FUEL TANK;
EMISSION CONTROL SYSTEMS......25-4,25-7
FILLER TUBE CAP, FUEL TANK; FUEL
SYSTEM............................14-13
FILLER TUBE, NO-LEAD FUEL TANK......14-13
FILTER DRIERÐ2.5L ENGINES,
CONDENSER........................24-27
FILTER DRIERÐ4.0L ENGINES..........24-28
FILTER, ENGINE OIL...................0-17
FILTER, FUEL; FUEL SYSTEM.......14-60,14-9
FILTER, FUEL; LUBRICATION AND
MAINTENANCE.......................0-19
FILTER REPLACEMENT, ENGINE OIL
CHANGE............................0-16
FILTER REPLACEMENT, FLUID..........21-99
FILTER REPLACEMENT, OIL............21-103
FIN SENSING CYCLING CLUTCH SWITCH . 24-15,
24-31
FINAL ASSEMBLY; FRONT SUSPENSION
AND AXLE...........................2-46
FINAL ASSEMBLY; REAR SUSPENSION
AND AXLES..........................3-29
FIRING ORDERÐ2.5L 4-CYLINDER
ENGINE, ENGINE.....................8D-32
FIRING ORDERÐ4.0L 6-CYLINDER
ENGINE, ENGINE.....................8D-32
FIRST-REVERSE BRAKE PISTON AND
TRANSMISSION CASE OVERHAUL......21-247
FIRST/SECOND/THIRD/REVERSE
COMPONENTS......................21-168
FITTING CHART, CONNECTING ROD
BEARING........................9-41,9-83
FITTING CHART, MAIN BEARING......9-48,9-90
FITTING O-RING SEAL, FLOW CONTROL
VALVE .............................19-14
FITTING SERVICE, TRANSMISSION
COOLER LINE......................21-111
FITTINGS, TRANSMISSION COOLER LINE . 21-197
FLAREÐYJ, FENDER.................23-114
FLARES AND LINERSÐXJ, REAR
WHEELHOUSE.......................23-19
FLASHER, COMBINATION; TURN
SIGNALS (XJ).....................8W-52-1
FLASHERS, HAZARD; TURN SIGNALS
(XJ).............................8W-52-1
FLASHERS, HAZARD; TURN SIGNALS
(XJ-RHD).........................8W-52-1
FLASHERS, HAZARD; TURN SIGNALS
(YJ).............................8W-52-1
FLOOR BRACKETSÐXJ, SPARE
TIRE/WHEEL HOLDDOWN..............23-98
FLOOR CONSOLEÐXJ, FULL...........23-95
FLOOR CONSOLESÐYJ...............23-155
FLOOR MATSÐXJ, CARPETS...........23-99
FLOOR SHIFTÐXJ, MINI-CONSOLE WITH . 23-94
FLOW CONTROL VALVE FITTING O-RING
SEAL..............................19-14
FLOW TESTING, TRANSMISSION
COOLER...........................21-113
FLUID AND FILTER REPLACEMENT.......21-99
FLUID CAPACITIES.....................0-3
FLUID, CLUTCH LINKAGE................6-1
FLUID CONTAMINATION, BRAKE.......5-10,5-7
FLUID LEVEL AND CONDITION,
CHECKING.........................21-182
FLUID LEVEL, BRAKE..................5-10
FLUID LEVEL CHECK.............21-70,21-99
FLUID LEVEL, CLUTCH.................6-14
FLUID, RECOMMENDED BRAKE..........5-10
FLUID WARNING LAMP, LOW WASHER;
INSTRUMENT CLUSTER (XJ).........8W-40-2
FLUID WARNING LAMP, LOW WASHER;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
FLUID/FILTER CHANGE, REFILLING
AFTER OVERHAUL OR..........21-100,21-182
FLUID/LUBRICANTS/CLEANING
SOLVENTS, BRAKE
.....................5-2
FLUIDÐBRAKE BLEEDINGÐ
BRAKELINES AND HOSES, BRAKE
........5-10
FLUSHING, COOLING SYSTEM
CLEANING/REVERSE
...................7-22
FLUSHING, TRANSMISSION COOLER
REVERSE
..........................21-114
FLYWHEEL RUNOUT
....................6-3FLYWHEEL SERVICE...................6-16
FOG LAMP DIAGNOSIS............8L-21,8L-3
FOG LAMP REPLACEMENTÐXJ..........8L-9
FOG LAMP REPLACEMENTÐYJ.........8L-25
FOG LAMP SWITCH REPLACEMENTÐXJ . . 8L-10
FOG LAMP SWITCH REPLACEMENTÐYJ . . 8L-26
FOG LAMPS; FRONT LIGHTING (XJ) . . . 8W-50-1
FOG LAMPS; FRONT LIGHTING (XJ-RHD) . 8W-50-2
FOG LAMPS; FRONT LIGHTING (YJ) . . . 8W-50-1
FOG LAMPSÐXJ......................8L-7
FOG LAMPSÐYJ.....................8L-23
FORM-IN-PLACE GASKETS...............9-1
FORMULAS AND EQUIVALENT VALUES,
CONVERSION.....................Intro.-11
FORWARD CLUTCH OVERHAUL........21-232
FOURTH GEAR OVERDRIVE
COMPONENTS......................21-167
FOUR-WHEEL DRIVE (4WD) SWITCH;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
FOUR-WHEEL DRIVE (4WD) SWITCH;
TRANSMISSION CONTROLS (XJ-RHD) . . 8W-31-1
FOUR-WHEEL-DRIVE VEHICLE TOWING....0-12
FRAME.........................13-10,13-1
FRAME CROSSMEMBER COVER.........13-16
FRAME DIMENSIONS.............13-13,13-1
FRAME GLASS CHANNEL
REPLACEMENTÐYJ, DOOR...........23-142
FRAME REPAIRS......................13-13
FRAME STRAIGHTENING...............13-13
FRAME WEATHERSTRIP SEALÐYJ,
WINDSHIELD.......................23-146
FRAMEÐXJ, BUCKET SEATBACK COVER . . 23-81
FRAMEÐYJ, WINDSHIELD............23-145
FREQUENCY INTERFERENCE, RADIO......8F-5
FRESH AIR DOOR VACUUM MOTOR......24-34
FRESH AIR INTAKE DUCT..............24-34
FRONT AND REAR AXLES...............0-24
FRONT AXLE, MODEL 30...............2-49
FRONT BUCKET SEATSÐXJ............23-81
FRONT BUMPER.................13-16,13-5
FRONT CABLE REPLACEMENT (YJ),
PARKING BRAKE......................5-67
FRONT CARPET/MATÐXJ..............23-99
FRONT CLUTCH OVERHAUL...........21-134
FRONT DOOR SPACER BLOCKSÐTWO-
DOOR VEHICLES.....................23-53
FRONT DOOR WINDOW GLASS
REGULATORÐXJ....................23-42
FRONT DOOR WINDOW GLASSÐXJ.....23-43
FRONT DRIVE AXLE....................2-3
FRONT FENDERÐXJ..................23-14
FRONT INNER SCUFF PLATE/COWL SIDE
TRIM PANELÐXJ....................23-86
FRONT PARK/TURN SIGNAL LAMP BULB
REPLACEMENTÐXJ...................8L-9
FRONT PARK/TURN SIGNAL LAMP BULB
REPLACEMENTÐYJ..................8L-25
FRONT PLANETARY GEAR OVERHAUL . . . 21-237
FRONT SERVO AND BAND OVERHAUL . . . 21-146
FRONT SHOULDER BELT/BUCKLEÐXJ....23-90
FRONT SHOULDER BELTSÐYJ.........23-154
FRONT SKID PLATE
....................13-1
FRONT SUSPENSION
...................2-1
FRONT SUSPENSION COMPONENTS, XJ
. . . 2-49
FRONT SUSPENSION COMPONENTS, YJ
. . . 2-49
FRONT SUSPENSION, XJ
...............2-11
FRONT SUSPENSION, YJ
...............2-15
FRONT TOW HOOKS
...................13-7
FRONT WHEEL ALIGNMENT
..............2-5
FRONT WHEEL BEARINGS
..............0-28
FRONT WHEEL SENSOR INSTALLATION
....5-38
FRONT WHEEL SENSOR REMOVAL
.......5-38
FUEL DELIVERY SYSTEM
...............14-3
FUEL FILLER DOOR BUMPERSÐXJ
......23-27
FUEL FILLER HOSE SPLASH SHIELDÐXJ
VEHICLES
...........................13-4
FUEL FILLER NOZZLE/TUBEÐXJ
........23-26
FUEL FILLER PROTECTOR/NOZZLEÐYJ
. . 23-121
FUEL FILTER; FUEL SYSTEM
........14-60,14-9
FUEL FILTER; LUBRICATION AND
MAINTENANCE
.......................0-19
FUEL GAUGE; INSTRUMENT CLUSTER
(XJ)
.............................8W-40-1
FUEL GAUGE; INSTRUMENT CLUSTER
(XJ-RHD)
.........................8W-40-1
FUEL GAUGE SENDING UNIT
...........14-16
10 INDEXJ
Description Group-Page Description Group-Page Description Group-Page