1995 JEEP YJ jump cable

INDICATOR LAMPS
If an individual indicator lamp is inoperative, see
the diagnostic procedure under the heading for that
lamp. If more than one indicator lamp or a combina-
tion of lamps and gauges in the main cluster or the
gauge package cluster is inoperative, see Gauges in
this section for diagnosis.
ANTI-LOCK BRAKE SYSTEM LAMP
The diagnosis found here addresses an inoperative
lamp condition. If the ABS lamp stays on with the ig-
nition switch in the ON position, or comes on and
stays on while driving, refer to Group 5 - Brakes for
diagnosis. If no ABS problem is found, the following
procedure will help locate a short or open in the ABS
lamp circuit.
(1) Disconnect battery negative cable. Remove left
instrument cluster bezel and main cluster assembly.
Disconnect ABS control module connector.
(2) Install a jumper wire between cavity 6 of clus-
ter connector and a good ground. Connect battery
negative cable. Turn ignition switch to ON. Lamp
should light. If OK, remove jumper wire and go to
next step. If not OK, replace bulb.
(3) Turn ignition switch to OFF. Disconnect battery
negative cable and unplug cluster connector. Check
for continuity between cavity 6 of cluster connector
and a good ground. There should be no continuity. If
OK, go to next step. If not OK, repair short circuit as
required.
(4) Check continuity between cavity 6 of cluster
connector and cavity 52 of ABS control module con-
nector (Fig. 6). There should be continuity. If OK, re-
fer to Group 5 - Brakes for diagnosis of ABS control
module. If not OK, repair open circuit as required.
BRAKE WARNING LAMP
The diagnosis found here addresses an inoperative
lamp condition. If the brake warning lamp stays on
with the ignition switch in the ON position and the
parking brake released, refer to Group 5 - Brakes for
diagnosis. If no service brake or parking brake prob-
lem is found, the following procedure will help locate
a short circuit or faulty switch.
(1) Unplug parking brake switch connector. Turn
ignition switch to START position. Lamp should
light. Release ignition switch to ON position. Lamp
should go off. If OK, go to step 10. If not OK, go to
next step.
(2) Unplug brake warning switch connector. Install
a jumper wire between two cavities of connector.
Turn ignition switch to START. Lamp should light.
Remove jumper wire and lamp should go off. If OK,
replace brake warning switch. If not OK, remove
jumper wire and go to next step.
(3) Turn ignition switch to ON position. Install a
jumper wire between brake warning switch connectorcavity for circuit G9 and a good ground. Lamp should
light. If OK, go to step 5. If not OK, go to next step.
(4) Turn ignition switch to OFF. Remove jumper
wire and disconnect battery negative cable. Remove
left instrument cluster bezel and main cluster. Install
a jumper wire between cavity 1 of cluster connector
and a good ground. Connect battery negative cable
and turn ignition switch to ON. Lamp should light. If
OK, repair open in circuit to brake warning switch. If
not OK, replace bulb.
(5) Turn ignition switch to OFF and remove
jumper wire. Disconnect battery negative cable.
Check for continuity between brake warning switch
connector cavity for circuit G11 and a good ground
with ignition switch in START position. There should
be continuity. If not OK, go to next step.
(6) Turn ignition switch to OFF and remove
jumper wire. Unplug ignition switch connectors.
Check for continuity between ignition switch connec-
tor cavity for G11 circuit and a good ground. There
should be no continuity. If OK, go to next step. If not
OK, repair short circuit between ignition switch and
brake warning switch connectors as required.
(7) Check for continuity between ignition switch
connector cavity for G11 circuit and brake warning
switch connector cavity for G11 circuit. There should
be continuity. If OK, go to next step. If not OK, re-
pair open circuit as required.
(8) Check for continuity between metal steering
column jacket and a good ground. There should be
continuity. If OK, go to next step. If not OK, refer to
Group 19 - Steering to check steering column ground
clip installation.
Fig. 6 ABS Control Module Connector
8E - 32 INSTRUMENT PANEL AND GAUGESÐYJJ

(9) Turn ignition switch to START position and
hold there. Check for continuity between terminal for
circuit G11 of ignition switch and a good ground.
There should be continuity. If not OK, replace igni-
tion switch.
(10) Unplug brake warning switch connector.
Check for continuity between parking brake switch
connector and a good ground. There should be no
continuity. If OK, go to next step. If not OK, repair
short circuit as required.
(11) Check for continuity between parking brake
switch connector and brake warning switch connector
cavity for circuit G11. There should be continuity. If
OK, replace parking brake switch. If not OK, repair
open circuit to brake warning switch as required.
FOUR-WHEEL DRIVE INDICATOR LAMP
(1) Apply parking brake, start engine, vehicle in
4WD Lock or 4WD.
(2) Unplug switch and touch harness side of wire
to ground. Lamp should light. If OK, check switch
operation, replace if bad. If bulb is OK, repair open
to indicator.
HEADLAMP HIGH BEAM INDICATOR LAMP
(1) Check that headlamp high beams are func-
tional. If OK, go to next step. If not OK, refer to
Group 8L - Lamps for diagnosis of headlamp system.
(2) Disconnect battery negative cable. Remove left
instrument cluster bezel and main cluster assembly.
Unplug cluster connector. Connect battery negative
cable. Turn headlamps on and select high beam.
Check for battery voltage at cavity 17 of cluster con-
nector. If OK, replace indicator bulb. If not OK, re-
pair circuit to headlamp dimmer switch as required.
MALFUNCTION INDICATOR LAMP
The diagnosis found here addresses an inoperative
lamp condition. If the lamp comes on and stays on
with engine running, refer to Group 14 - Fuel System
for diagnosis. If no fuel or emission system problem
is found, the following procedure will help locate a
short or open in the lamp circuit.
(1) Disconnect battery negative cable. Unplug PCM
connector. Install a jumper wire from cavity 32 of
PCM connector (Fig. 5) to a good ground. Connect
battery negative cable. Turn ignition switch to ON.
Lamp should light. Remove jumper wire and lamp
should go OFF. If OK, refer to Powertrain Diagnostic
Procedures to check PCM. If not OK, go to next step.
(2) Turn ignition switch to OFF. Disconnect battery
negative cable. Remove left instrument cluster bezel
and main cluster assembly. Install a jumper wire
from cavity 2 of cluster connector to a good ground.
Connect battery negative cable. Turn ignition switch
to ON. Lamp should light. If OK, go to next step. If
not OK, replace bulb.(3) Turn ignition switch to OFF. Disconnect battery
negative cable. Unplug cluster connector. Check for
continuity between cavity 2 of cluster connector and
a good ground. There should be no continuity. If OK,
go to next step. If not OK, repair short circuit to
PCM as required.
(4) Check continuity between cavity 2 of cluster
connector and cavity 32 of PCM connector. There
should be continuity. If not OK, repair open circuit to
PCM as required.
SEAT BELT REMINDER LAMP
(1) Refer to Group 8U - Chime/Buzzer Warning
Systems to check chime/buzzer module operation. If
OK, go to next step. If not OK, replace chime/buzzer
module.
(2) Disconnect battery negative cable. Remove left
instrument cluster bezel and main cluster assembly.
Unplug cluster connector. Check for continuity be-
tween cavity 20 of cluster connector and a good
ground. There should be continuity. If OK, plug clus-
ter connector back into cluster and go to next step. If
not OK, repair open circuit to ground as required.
(3) Connect battery negative cable. Install a
jumper wire between a 12-volt battery feed and cav-
ity 16 of cluster connector. Lamp should light. If OK,
go to next step. If not OK, replace bulb.
(4) Disconnect battery negative cable. Unplug
chime/buzzer module from fuseblock module. Unplug
cluster connector. Check for continuity between cav-
ity 16 of cluster connector and a good ground. There
should be no continuity. If OK, go to next step. If not
OK, repair short circuit to chime/buzzer module as
required.
(5) Check continuity between cavity 16 of cluster
connector and cavity for terminal A3 of chime/buzzer
module (Fig. 7) in fuseblock module. There should be
continuity. If not OK, repair open circuit to chime/
buzzer module as required.
Fig. 7 Chime/Buzzer Module Receptacle
JINSTRUMENT PANEL AND GAUGESÐYJ 8E - 33

TURN SIGNAL INDICATOR LAMPS
(1) Disconnect battery negative cable. Remove left
instrument cluster bezel and main cluster assembly.
Probe cavity 20 of cluster connector. Check for conti-
nuity to a good ground. There should be continuity. If
OK, go to next step. If not OK, repair open circuit to
ground.
(2) Connect battery negative cable. Install a
jumper wire from cavity 18 (left indicator) or cavity 7
(right indicator) of cluster connector to a 12-volt bat-
tery feed. Lamp should light. If OK, continue to next
step. If not OK, replace bulb.
(3) Disconnect battery negative cable. Check for
continuity between cavity 18 (left indicator) or cavity
7 (right indicator) of cluster connector and cavity H
(left front turn signal) or cavity J (right front turn
signal) of steering column wiring connector. There
should be continuity. If OK, refer to Group 8J - Turn
Signal and Hazard Warning Systems for further di-
agnosis. If not OK, repair open circuit as required.
UPSHIFT INDICATOR LAMP
(1) Disconnect battery negative cable. Unplug PCM
connector. Connect battery negative cable. Turn igni-
tion switch to ON. Install a jumper wire from cavity
54 of PCM connector (Fig. 5) to a good ground. Lamp
should light. Remove jumper from ground. Lamp
should go off. If OK, refer to Powertrain Diagnostic
Procedures manual to diagnose PCM. If not OK, turn
ignition switch to OFF and go to next step.
(2) Disconnect battery negative cable. Remove left
instrument cluster bezel and main cluster assembly.
Install a jumper wire from cavity 5 of cluster connec-
tor to a good ground. Connect battery negative cable.
Turn ignition switch to ON. Lamp should light. If
OK, go to next step. If not OK, replace bulb.
(3) Turn ignition switch to OFF. Disconnect battery
negative cable. Unplug cluster connector. Check for
continuity between cavity 5 of cluster connector and
a good ground. There should be no continuity. If OK,
go to next step. If not OK, repair short circuit as re-
quired.(4) Check for continuity between cavity 5 of cluster
connector and cavity 54 of PCM connector. There
should be continuity. If not OK, repair open circuit as
required.
CLUSTER ILLUMINATION LAMPS
(1) Check fuse 10 in fuseblock module. If OK, go to
next step. If not OK, replace fuse.
(2) Turn park lamps on at headlamp switch. Rotate
panel dimmer switch thumb-wheel to HI position,
just before interior lamps detent. Check for battery
voltage at fuse 10 in fuseblock module. Rotate panel
dimmer thumb-wheel towards LO position while ob-
serving test voltmeter. Reading should go from bat-
tery voltage to zero volts. If OK, go to next step. If
not OK, repair open circuit to headlamp switch or re-
fer to Group 8L - Lamps to diagnose headlamp
switch.
(3) Disconnect battery negative cable. Remove left
or center instrument cluster bezel and main or gauge
package cluster assembly. Unplug cluster connector.
Connect battery negative cable. Turn park lamps on
at headlamp switch. Rotate panel dimmer thumb-
wheel to HI position, just before interior lamps de-
tent. Check for battery voltage at cavity 21 of main
cluster connector, or cavity 7 of gauge package clus-
ter connector. If OK, go to next step. If not OK, re-
pair open circuit to fuse as required.
(4) Turn park lamps off. Disconnect battery nega-
tive cable. Remove fuse 10 from fuseblock module.
Probe cavity 21 of main cluster connector, or cavity 7
of gauge package cluster connector. Check for conti-
nuity to a good ground. There should be no continu-
ity. If OK, go to next step. If not OK, repair short
circuit as required.
(5) Probe cavity 20 of main cluster connector, or
cavities 1 and 13 of gauge package cluster connector.
Check for continuity to ground. There should be con-
tinuity. If not OK, repair open circuit as required.
8E - 34 INSTRUMENT PANEL AND GAUGESÐYJJ

STARTING SYSTEM
STARTING SYSTEM
AUTOMATIC TRANSMISSIONS
Circuit A0 from the battery is double crimped at
the positive battery post. One branch of circuit A0
(battery positive cable) connects to the engine starter
motor. The other A0 branch supplies voltage to the
bus bar in the Power Distribution Center (PDC).
The PDC supplies battery voltage to the engine
starter motor solenoid on circuit T40 when the coil
side of the engine starter motor relay energizes. Cir-
cuit A1 from the fuse 4 in the PDC supplies battery
voltage to the contact side of the starter motor relay.
The ignition switch supplies battery voltage to the
coil side of the starter motor relay on circuit A41
when the key is moved to the START position and
the Park/Neutral position switch is closed. Ground
for the coil side of the starter motor relay is supplied
by the case grounded Park/Neutral position switch.
Circuit T41 connects the coil side of the relay to the
Park/Neutral position switch.
When the starter motor relay energizes and the
contacts close, circuit T40 supplies battery voltage to
the starter motor solenoid. Circuit A0 from the bat-
tery supplies voltage to the starter motor when the
solenoid energizes.
MANUAL TRANSMISSIONS
Circuit A0 from the battery is double crimped at
the positive battery post. One branch of circuit A0
(battery positive cable) connects to the battery
starter motor. The other A0 branch supplies voltage
to the bus bar in the Power Distribution Center
(PDC).The PDC supplies battery voltage to the engine
starter motor solenoid on circuit T40 when the coil
side of the engine starter motor relay energizes. Cir-
cuit A1 from the fuse 4 in the PDC supplies battery
voltage to the contact side of the starter motor relay.
The ignition switch supplies battery voltage to the
coil side of the starter motor relay on circuit A41
when the key is moved to the START position. Cir-
cuit T41 from the coil side of the relay connects to a
Z2 jumper wire in the back-up lamp switch. Circuit
Z2 provides ground for the starter motor relay.
When the starter motor relay energizes and the
contacts close, circuit T40 supplies battery voltage to
the starter motor solenoid. Circuit A0 from the bat-
tery supplies voltage to the starter motor when the
solenoid energizes.
HELPFUL INFORMATION
²The Park/Neutral switch closes when the trans-
mission is in either the PARK or NEUTRAL posi-
tions.
²Circuit T41 also connects to cavity 30 of the Pow-
ertrain Control Module (PCM). This input tells the
PCM the operator is starting the vehicle.
DIAGRAM INDEX
Component Page
Engine Starter Motor......................8W-21-2
Engine Starter Motor Relay..................8W-21-2
Ignition Switch..........................8W-21-2
Park/Neutral Position Switch.................8W-21-2
Power Distribution Center (PDC)...............8W-21-2
Powertrain Control Module (PCM)..............8W-21-2
Fuse 4 (PDC)...........................8W-21-2
J8W-21 STARTING SYSTEMÐYJ VEHICLES 8W - 21 - 1

HEATER AND A/C CONTROL
REPLACEMENT......................24-23
HEATER AND A/C OPERATION...........24-1
HEATER AND AIR CONDITIONING; AIR
CONDITIONING/HEATER (YJ).........8W-42-2
HEATER CONTROL PANEL LAMP,
ACCESSORY LAMP; INTERIOR
LIGHTING (YJ)....................8W-44-1
HEATER CONTROL REPLACEMENT.......24-32
HEATER CORE.......................24-26
HEATER CORE AND HOUSING..........24-33
HEATER DIAGNOSIS..................24-17
HEATER ELEMENTS; POWER MIRRORS
(XJ-RHD).........................8W-62-1
HEATER, ENGINE BLOCK................7-44
HEATER HOUSING REPLACEMENT.......24-26
HEATER SYSTEM; AIR CONDITIONING/
HEATER (XJ)......................8W-42-1
HEATER SYSTEM; AIR CONDITIONING/
HEATER (XJ-RHD)..................8W-42-1
HEATER SYSTEM; AIR CONDITIONING/
HEATER (YJ)......................8W-42-1
HEATER/DEFROSTER/INSTRUMENT
PANEL OUTLET VACUUM MOTOR
REPLACEMENT......................24-26
HEATING AND AIR CONDITIONING TEST
PROCEDURES.......................24-15
HEATING ELEMENT TEST, OXYGEN
SENSOR (O2S)......................14-48
HEATING SCHEMATICÐXJ..............24-2
HEATING SYSTEM DIAGNOSIS..........24-18
HELPFUL INFORMATION; CHARGING
SYSTEM (XJ).....................8W-20-1
HELPFUL INFORMATION; CHARGING
SYSTEM (XJ-RHD).................8W-20-1
HELPFUL INFORMATION; CHARGING
SYSTEM (YJ).....................8W-20-1
HELPFUL INFORMATION; POWER SEAT
(XJ).............................8W-63-1
HELPFUL INFORMATION; POWER
WINDOWS (XJ)....................8W-60-2
HELPFUL INFORMATION; POWER
WINDOWS (XJ-RHD)...............8W-60-2
HELPFUL INFORMATION; TRAILER TOW
(XJ).............................8W-54-1
HELPFUL INFORMATION; TRAILER TOW
(XJ-RHD).........................8W-54-1
HIGH MOUNTED STOP LAMP
(CHMSL)ÐXJ, CENTER................8L-12
HIGH MOUNTED STOP LAMP
(CHMSL)ÐYJ, CENTER................8L-28
HIGH PEDAL EFFORT, HARD PEDAL OR.....5-6
HIGH-BEAM INDICATOR LAMP;
INSTRUMENT CLUSTER (XJ).........8W-40-2
HIGH-BEAM INDICATOR LAMP;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
HIGH-LINE GAUGE CLUSTER (LHD).......8E-9
HIGH-PRESSURE CUT-OFF SWITCH,
LOW-PRESSURE................24-15,24-16
HINGE REPLACEMENTÐXJ, HOOD.......23-10
HINGE/HINGE PIN REPLACEMENTÐXJ,
DOOR.............................23-52
HINGEÐXJ, LIFTGATE.................23-60
HINGEÐYJ, TAILGATE................23-121
HINGESÐYJ, FULL-METAL DOOR.......23-140
HITCH, TRAILER.....................23-77
HITCHÐXJ, TRAILER.................23-77
HOISTING, JUMP STARTING, TOWING......0-9
HOISTING RECOMMENDATIONS..........0-10
HOLD AFTER DRIVING THROUGH DEEP
WATER PUDDLES, BRAKES DO NOT.......5-7
HOLDDOWN AND FLOOR BRACKETSÐ
XJ, SPARE TIRE/WHEEL...............23-98
HONING CYLINDER BORES...............9-2
HOOD ADJUSTMENTÐXJ..............23-10
HOOD ALIGNMENTÐYJ..............23-107
HOOD HINGE REPLACEMENTÐXJ.......23-10
HOOD INSULATOR PANELÐYJ.........23-107
HOOD LATCH REPLACEMENTÐXJ.......23-11
HOOD LATCH STRIKER REPLACEMENTÐ
XJ ................................23-11
HOOD SAFETY LATCHÐYJ............23-109
HOODÐXJ...........................23-7
HOODÐYJ
.........................23-107
HOOK, REAR TOW
.....................13-9
HOOKS, FRONT TOW
..................13-7
HOOKS, TOW
........................13-13
HORN; HORN/CIGAR LIGHTER
...........8E-1HORN; HORN/CIGAR LIGHTER (YJ)....8W-41-1
HORN; INSTRUMENT CLUSTER (XJ) . . . 8W-40-1
HORN CONTACT/CLOCKSPRING..........8G-4
HORN RELAY........................8G-1
HORN REMOVE/INSTALL...............8G-3
HORN SWITCH.......................8G-1
HORN SWITCH REMOVE/INSTALL........8G-3
HORNS.............................8G-1
HOSE REPLACEMENT, PRESSURE AND
RETURN............................19-11
HOSE ROUTING SCHEMATICS, VACUUM . . . 25-2
HOSE SPLASH SHIELDÐXJ VEHICLES,
FUEL FILLER.........................13-4
HOSES, BRAKE FLUIDÐBRAKE
BLEEDINGÐBRAKELINES...............5-10
HOSES, BRAKELINES..................5-12
HOSES, COOLING SYSTEM..............7-32
HOSES/TUBES PRECAUTIONS,
REFRIGERANT.......................24-10
HOSES/TUBING, RUBBER AND PLASTIC....0-26
HOUSING, AIR CLEANER...............14-58
HOUSING COMPONENTSÐYJ,
EVAPORATIVE........................24-6
HOUSING END PLUG..................19-28
HOUSING, EVAPORATOR...............24-35
HOUSING, EVAPORATOR/BLOWER.......24-29
HOUSING, HEATER CORE..............24-33
HOUSING INSPECTION AND PARK LOCK
COMPONENT OVERHAUL, ADAPTER/
EXTENSION........................21-127
HOUSING LEAK DIAGNOSIS,
CONVERTER........................21-75
HOUSING MISALIGNMENT, CLUTCH........6-4
HOUSING REPLACEMENT, CLUTCH.......6-13
HOUSING REPLACEMENT, HEATER.......24-26
HOUSING SEAL REPLACEMENT,
ADAPTER..........................21-191
HOUSINGÐXJ, LIFTGATE LICENSE
PLATE LAMP........................23-65
HOUSINGSÐYJ, INSTRUMENT CLUSTER
AND GAUGE........................23-151
HOW TO USE THIS GROUP; WIRING
DIAGRAMS (XJ)......................8W-1
HOW TO USE THIS GROUP; WIRING
DIAGRAMS (XJ-RHD)..................8W-1
HOW TO USE THIS GROUP; WIRING
DIAGRAMS (YJ)......................8W-1
HUB BEARING AND AXLE SHAFT.........2-25
HYDRAULIC CONTROL UNIT; ANTI-LOCK
BRAKES (XJ)......................8W-32-2
HYDRAULIC CONTROL UNIT; ANTI-LOCK
BRAKES (XJ-RHD).................8W-32-2
HYDRAULIC CONTROL UNIT; ANTI-LOCK
BRAKES (YJ)......................8W-32-2
HYDRAULIC CONTROL UNIT (HCU).......5-33
HYDRAULIC LINKAGE COMPONENTS.......6-1
HYDRAULIC LINKAGE INSTALLATION,
CLUTCH.............................6-14
HYDRAULIC LINKAGE REMOVAL,
CLUTCH.............................6-13
HYDRAULIC PRESSURE TEST.....21-177,21-72
HYDRAULIC SYSTEM................21-169
HYDRAULIC TAPPETS..............9-24,9-66
HYDROSTATIC LOCK
....................9-4
IDENTIFICATION, AW-4 ACCUMULATOR
COMPONENT
.......................21-342
IDENTIFICATION, AW-4 VALVE AND
SPRING
...........................21-343
IDENTIFICATION, BOLT
..............Intro.-14
IDENTIFICATION, CIRCUIT; WIRING
DIAGRAMSÐGENERAL INFORMATION
(XJ)
...............................8W-1
IDENTIFICATION, ENGINE AND
TRANSMISSION/TRANSFER CASE
......Intro.-5
IDENTIFICATION, MAJOR COMPONENT
. . Intro.-5
IDENTIFICATION NUMBER (VIN)
DECODING, VEHICLE
................Intro.-4
IDENTIFICATION NUMBER (VIN) PLATE,
VEHICLE
..........................Intro.-4
IDENTIFICATION, SECTION; WIRING
DIAGRAMS (XJ)
......................8W-1
IDENTIFICATION, SECTION; WIRING
DIAGRAMS (XJ-RHD)
..................8W-1
IDENTIFICATION, SECTION; WIRING
DIAGRAMS (YJ)
......................8W-1
IDENTIFICATION, TRANSFER CASE
.....21-284,
21-307IDENTIFICATION, TRANSMISSION . 21-166,21-33,
21-67,21-2
IDENTIFICATION, WIRE CODE; WIRING
DIAGRAMSÐGENERAL INFORMATION
(XJ)...............................8W-1
IDENTIFICATION/SYSTEM OPERATION,
COMPONENT.........................8D-1
IDLE AIR CONTROL (IAC) MOTOR; FUEL
SYSTEM............................14-62
IDLE AIR CONTROL (IAC) MOTOR;
FUEL/IGNITION (XJ)................8W-30-2
IDLE AIR CONTROL (IAC) MOTOR;
FUEL/IGNITION (YJ)................8W-30-2
IDLE AIR CONTROL (IAC) MOTOR;
FUEL/IGNITION (XJ-RHD)............8W-30-2
IDLE AIR CONTROL (IAC) MOTORÐPCM
OUTPUT............................14-27
IDLE AIR CONTROL MOTOR TEST.......14-49
IDLE SWITCH, EXTENDED...........8W-30-5
IDLE SWITCH TEST, EXTENDED.........14-48
IDLE SWITCHÐPCM INPUT, EXTENDED . . . 14-23
IGNITION CABLES, DISTRIBUTOR CAP
AND ROTOR.........................0-20
IGNITION CIRCUIT SENSEÐPCM INPUT . . 14-23
IGNITION COIL; FUEL SYSTEM..........14-62
IGNITION COIL; FUEL/IGNITION (XJ) . . . 8W-30-2
IGNITION COIL; FUEL/IGNITION (YJ) . . . 8W-30-2
IGNITION COIL; IGNITION SYSTEMS.....8D-22,
8D-4,8D-9
IGNITION COIL; FUEL/IGNITION
(XJ-RHD).........................8W-30-2
IGNITION COIL RESISTANCE............8D-9
IGNITION COILÐPCM OUTPUT..........14-28
IGNITION FEED; FUEL/IGNITION
(XJ-RHD).........................8W-30-1
IGNITION KEY-IN SWITCH..........8U-1,8U-2
IGNITION SECONDARY CIRCUIT
DIAGNOSIS.........................8D-10
IGNITION SWITCH; BRAKES.............5-35
IGNITION SWITCH; FUEL/IGNITION (XJ) . 8W-30-1
IGNITION SWITCH; FUEL/IGNITION (YJ) . 8W-30-1
IGNITION SWITCH; FUEL/IGNITION
(XJ-RHD).........................8W-30-1
IGNITION SWITCH AND KEY CYLINDER
SERVICE...........................8D-26
IGNITION SWITCH CONTINUITY TESTS . . . 8D-30
IGNITION SWITCH LAMP; INTERIOR
LIGHTING (XJ)....................8W-44-1
IGNITION SWITCH LAMP; INTERIOR
LIGHTING (XJ-RHD)................8W-44-1
IGNITION SWITCH SERVICE............19-54
IGNITION SWITCHÐXJ MODELS........8D-26
IGNITION SWITCHÐYJ MODELS........8D-29
IGNITION TIMING....................8D-11
ILLUMINATION LAMPS, CLUSTER . . 8E-16,8E-26,
8E-34,8E-4
ILLUMINATION LAMPS, INSTRUMENT
PANEL; INTERIOR LIGHTING (XJ).....8W-44-1
ILLUMINATION LAMPS, INSTRUMENT
PANEL; INTERIOR LIGHTING (XJ-RHD) . 8W-44-1
ILLUMINATION, RADIO; RADIO (XJ)....8W-47-1
ILLUMINATION, RADIO; RADIO
(XJ-RHD).........................8W-47-1
ILLUMINATION, RADIO; RADIO (YJ)....8W-47-1
ILLUMINATION RELAY CONNECTIONS,
RADIO
..............................8F-4
ILLUMINATION RELAY, RADIO
........8F-1,8F-4
IMPACT SENSOR/INFLATOR ASSEMBLY
. . . 8M-2
INCORRECT FLUID LEVEL, EFFECTS OF
. . . 21-71
INDEX, DIAGRAM; AIR CONDITIONING/
HEATER (XJ)
......................8W-42-2
INDEX, DIAGRAM; AIR CONDITIONING/
HEATER (XJ-RHD)
..................8W-42-2
INDEX, DIAGRAM; AIR CONDITIONING/
HEATER (YJ)
...............8W-42-1,8W-42-2
INDEX, DIAGRAM; ANTI-LOCK BRAKES
(XJ)
.............................8W-32-3
INDEX, DIAGRAM; ANTI-LOCK BRAKES
(XJ-RHD)
.........................8W-32-3
INDEX, DIAGRAM; ANTI-LOCK BRAKES
(YJ)
.............................8W-32-2
INDEX, DIAGRAM; CHARGING SYSTEM
(XJ)
.............................8W-20-1
INDEX, DIAGRAM; CHARGING SYSTEM
(XJ-RHD)
.........................8W-20-1
INDEX, DIAGRAM; CHARGING SYSTEM
(YJ)
.............................8W-20-1
JINDEX 13
Description Group-Page Description Group-Page Description Group-Page

INSTALLATION, DRUM BRAKESHOE.......5-55
INSTALLATION, FRONT WHEEL SENSOR . . . 5-38
INSTALLATION METHODS AND PARTS
USAGE...............................6-4
INSTALLATION (NON-ABS), MASTER
CYLINDER...........................5-16
INSTALLATION, ROTOR.................5-51
INSTALLATION, TRANSFER CASE . 21-288,21-309
INSTALLATION, TRANSMISSION.....21-36,21-5
INSTALLATION, TRANSMISSION AND
CONVERTER.......................21-117
INSTALLATION, TRANSMISSION AND
TORQUE CONVERTER................21-199
INSTALLATION, TRANSMISSION VALVE
BODY.............................21-187
INSTALLATION, VALVE BODY..........21-104
INSTALLATION, WHEEL.................22-6
INSTALLATION, WHEEL CYLINDER........5-58
INSTALLATION (WITH ABS), MASTER
CYLINDER AND COMBINATION VALVE.....5-20
INSTALLATION (XJ), HCU...............5-43
INSTALLATION (XJ MODELS), ECU........5-40
INSTALLATION (XJ), SHIFT LEVER......21-286,
21-309
INSTALLATION (XJ WITH ABS), POWER
BRAKE BOOSTER.....................5-27
INSTALLATION (XJ WITH FULL
CONSOLE), PARKING BRAKE LEVER.......5-64
INSTALLATION (XJ WITH MINI
CONSOLE), PARKING BRAKE LEVER.......5-63
INSTALLATION (XJ WITHOUT ABS),
POWER BRAKE BOOSTER...............5-30
INSTALLATION (XJ WITHOUT CONSOLE),
PARKING BRAKE LEVER................5-65
INSTALLATION (YJ), HCU...............5-44
INSTALLATION (YJ), PARKING BRAKE
PEDAL..............................5-66
INSTALLATION (YJ), POWER BRAKE
BOOSTER............................5-30
INSTALLATION (YJ), SHIFT LEVER......21-286
INSTRUMENT CLUSTER; INSTRUMENT
CLUSTER (XJ).....................8W-40-1
INSTRUMENT CLUSTER; INSTRUMENT
CLUSTER (XJ-RHD)................8W-40-1
INSTRUMENT CLUSTER; INSTRUMENT
CLUSTER (YJ).....................8W-40-1
INSTRUMENT CLUSTER AND GAUGE
HOUSINGSÐYJ.....................23-151
INSTRUMENT CLUSTER BEZELÐXJ......23-80
INSTRUMENT CLUSTER BEZELÐYJ.....23-151
INSTRUMENT CLUSTERS..........8E-24,8E-1
INSTRUMENT PANEL.............8E-24,8E-1
INSTRUMENT PANEL AND GAUGESÐYJ . . 8E-24
INSTRUMENT PANEL COMPONENTSÐYJ . 23-152
INSTRUMENT PANEL ILLUMINATION
LAMPS; INTERIOR LIGHTING (XJ).....8W-44-1
INSTRUMENT PANEL ILLUMINATION
LAMPS; INTERIOR LIGHTING (XJ-RHD) . 8W-44-1
INSTRUMENT PANEL REMOVE/INSTALL . . . 8E-20
INSTRUMENT PANELÐYJ.............23-151
INSULATOR PANELÐXJ, DASH PANEL....23-12
INSULATOR PANELÐYJ, HOOD........23-107
INTAKE AIR TEMPERATURE SENSOR;
FUEL/IGNITION (XJ)................8W-30-4
INTAKE AIR TEMPERATURE SENSOR;
FUEL/IGNITION (YJ)................8W-30-4
INTAKE AIR TEMPERATURE SENSOR;
FUEL/IGNITION (XJ-RHD)............8W-30-4
INTAKE DUCT, FRESH AIR..............24-34
INTAKE MANIFOLD...................14-63
INTAKE MANIFOLD AIR TEMPERATURE
SENSOR; FUEL SYSTEM...............14-60
INTAKE MANIFOLD AIR TEMPERATURE
SENSOR; IGNITION SYSTEMS......8D-23,8D-5
INTAKE MANIFOLD AIR TEMPERATURE
SENSOR TEST; FUEL SYSTEM..........14-46
INTAKE MANIFOLD AIR TEMPERATURE
SENSOR TEST; IGNITION SYSTEMS......8D-11
INTAKE MANIFOLD AIR TEMPERATURE
SENSORÐPCM INPUT................14-22
INTAKE MANIFOLD LEAKAGE DIAGNOSIS . . . 9-5
INTAKE MANIFOLDÐ2.5L ENGINE........11-7
INTAKE MANIFOLDÐ4.0L ENGINE
........11-8
INTERCHANGEABILITY, TRANSMISSION
CHANGES AND PARTS
................21-67
INTERFERENCE, RADIO FREQUENCY
......8F-5
INTERIOR COMPONENTS
........23-151,23-80
INTERIOR LAMPS
...............8L-16,8L-31INTERIOR LAMPSÐXJ................8L-18
INTERIOR LAMPSÐYJ................8L-32
INTERIOR REARVIEW MIRROR
SUPPORT BRACKET REPLACEMENTÐ
XJ ................................23-68
INTERIOR REARVIEW MIRRORÐXJ......23-66
INTERIOR TRIM PANELS AND SCUFF
PLATESÐXJ........................23-84
INTERLOCK CABLE ADJUSTMENT, PARK . 21-195
INTERLOCK CABLE ADJUSTMENT (XJ),
PARK .............................21-101
INTERLOCK MECHANISM, AUTOMATIC
TRANSMISSION SHIFTER/IGNITION......19-55
INTERMEDIATE (COUPLER) SHAFT.......19-45
INTERMEDIATEÐCOUPLING SHAFT......19-23
INTERMITTENT AND POOR
CONNECTIONS; WIRING DIAGRAMSÐ
GENERAL INFORMATION (XJ)...........8W-4
INTERMITTENT WIPE MODULE..........8K-4
INTERMITTENT WIPE SWITCH TESTING . . 8K-15
INTERMITTENT WIPERS; WIPERS
(XJ-RHD).........................8W-53-1
INTERNATIONAL SYMBOLS...............0-1
INTERNATIONAL VEHICLE CONTROL
AND DISPLAY SYMBOLS.............Intro.-5
INTRODUCTION; BODY COMPONENTSÐ
XJ VEHICLES.......................23-158
INTRODUCTION; LUBRICATION AND
MAINTENANCE.....................0-1,0-4
IN-VEHICLE SERVICE, 30RH/32RH.......21-99
IN-VEHICLE SERVICE, AW-4.............21-182
I/P ASH RECEIVER TRAY LAMPÐXJ.....23-80
JACK STORAGEÐXJ..................23-97
JAMB SWITCH, DRIVER'S DOOR.....8U-1,8U-2
JEEP BODY CODE LETTERS..............5-2
JOINT ANGLE MEASUREMENT,
UNIVERSAL..........................16-4
JOINT REPLACEMENT, UNIVERSAL.......16-10
JOINTS, UNIVERSAL...................16-2
JUMP STARTING PROCEDURE............0-9
JUMP STARTING, TOWING AND
HOISTING............................0-9
KEY CYLINDER SERVICE, IGNITION
SWITCH............................8D-26
KEY LOCK CYLINDERÐXJ, DOOR.......23-47
KEY LOCK CYLINDERÐYJ, FULL-METAL
DOOR............................23-139
KEY-IN SWITCH, IGNITION..........8U-1,8U-2
KEYLESS ENTRY MODULE..........8P-1,8P-7
KEYLESS ENTRY MODULE, REMOTE . . . 8W-61-1
KEYLESS ENTRY MODULE REMOVE/
INSTALL...........................8P-10
KEYLESS ENTRY RECEIVER.............8C-1
KEYLESS ENTRY RECEIVERÐXJ........23-93
KEYLESS ENTRY TRANSMITTER . 8P-1,8P-7,8P-8
KEYS ARE NOT AVAILABLE, TOWING
WHEN..............................0-13
KNOCK, LOW SPEED; FRONT
SUSPENSION AND AXLE................2-19
KNOCK, LOW SPEED; REAR
SUSPENSION AND AXLES...............3-10
KNUCKLE AND BALL STUDS, STEERING . . . 2-32
LABEL, VEHICLE EMISSION CONTROL
INFORMATION (VECI)..................25-1
LABEL, VEHICLE SAFETY CERTIFICATION . Intro.-4
LABELS AND PLATESÐXJ, VEHICLE....Intro.-2
LABELS AND PLATESÐYJ, VEHICLE....Intro.-3
LABELS/DECALS/PLATESÐXJ............23-1
LABELS/DECALS/PLATESÐYJ..........23-102
LABELS/PLATES, CODES AND
DIMENSIONS, DESIGNATIONS.........Intro.-1
LAG TEST, TIME....................21-178
LAMP, ABS WARNING; ANTI-LOCK
BRAKES (XJ)......................8W-32-2
LAMP, ABS WARNING; ANTI-LOCK
BRAKES (XJ-RHD).................8W-32-2
LAMP, ABS WARNING; ANTI-LOCK
BRAKES (YJ)......................8W-32-2
LAMP, ABS WARNING; INSTRUMENT
CLUSTER (XJ)
.....................8W-40-2
LAMP, ABS WARNING; INSTRUMENT
CLUSTER (XJ-RHD)
................8W-40-2
LAMP, ABS WARNING; INSTRUMENT
CLUSTER (YJ)
.....................8W-40-2
LAMP, ACCESSORY LAMP AND HEATER
CONTROL PANEL
..................8W-44-1
LAMP ADJUSTMENT USING ALIGNMENT
SCREENÐXJ, HEADLAMP/FOG
...........8L-7LAMP ADJUSTMENT USING ALIGNMENT
SCREENÐYJ, HEADLAMP/FOG..........8L-23
LAMP AND DOME LAMP, CARGO......8W-44-1
LAMP AND HEATER CONTROL PANEL
LAMP, ACCESSORY.................8W-44-1
LAMP, BRAKE WARNING; INSTRUMENT
CLUSTER (XJ).....................8W-40-2
LAMP, BRAKE WARNING; INSTRUMENT
CLUSTER (XJ-RHD)................8W-40-2
LAMP, BRAKE WARNING; INSTRUMENT
CLUSTER (YJ).....................8W-40-2
LAMP BULB REMOVE/INSTALL,
READING/COURTESY..................8C-8
LAMP BULB REPLACEMENTÐXJ,
BACK-UP/REAR TURN SIGNAL/TAIL......8L-12
LAMP BULB REPLACEMENTÐXJ, FRONT
PARK/TURN SIGNAL...................8L-9
LAMP BULB REPLACEMENTÐXJ, SIDE
MARKER...........................8L-10
LAMP BULB REPLACEMENTÐXJ,
UNDERHOOD........................8L-13
LAMP BULB REPLACEMENTÐYJ,
BACK-UP/REAR TURN SIGNAL/TAIL......8L-28
LAMP BULB REPLACEMENTÐYJ, FRONT
PARK/TURN SIGNAL..................8L-25
LAMP BULB REPLACEMENTÐYJ, SIDE
MARKER...........................8L-25
LAMP BULB REPLACEMENTÐYJ,
UNDERHOOD........................8L-29
LAMP BULB REPLACEMENTÐYJ
VEHICLES, HARDTOP DOME/CARGO.....8L-31
LAMP, CARGO LAMP AND DOME;
INTERIOR LIGHTING (XJ-RHD)........8W-44-1
LAMP, CARGO LAMP, COURTESY LAMPS
AND DOME; INTERIOR LIGHTING (XJ) . . 8W-44-1
LAMP, CHARGING SYSTEM INDICATOR;
INSTRUMENT CLUSTER (XJ).........8W-40-3
LAMP (CHMSL)ÐXJ, CENTER HIGH
MOUNTED STOP.....................8L-12
LAMP (CHMSL)ÐYJ, CENTER HIGH
MOUNTED STOP.....................8L-28
LAMP, COURTESY LAMPS AND DOME
LAMP, CARGO; INTERIOR LIGHTING
(XJ).............................8W-44-1
LAMP DIAGNOSIS, FOG...........8L-21,8L-3
LAMP (DRL) MODULE, DAYTIME
RUNNING; FRONT LIGHTING (XJ).....8W-50-2
LAMP (DRL) MODULEÐCANADIAN
VEHICLES ONLY, DAYTIME RUNNING;
FRONT LIGHTING (YJ)..............8W-50-2
LAMP, ENGINE COOLANT TEMPERATURE
WARNING; INSTRUMENT CLUSTER
(XJ).............................8W-40-1
LAMP, ENGINE COOLANT TEMPERATURE
WARNING; INSTRUMENT CLUSTER
(XJ-RHD).........................8W-40-1
LAMP, GLOVE BOX; INTERIOR LIGHTING
(XJ).............................8W-44-1
LAMP, GLOVE BOX; INTERIOR LIGHTING
(XJ-RHD).........................8W-44-1
LAMP, HIGH-BEAM INDICATOR;
INSTRUMENT CLUSTER (XJ).........8W-40-2
LAMP, HIGH-BEAM INDICATOR;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
LAMP HOUSINGÐXJ, LIFTGATE LICENSE
PLATE .............................23-65
LAMP, IGNITION SWITCH; INTERIOR
LIGHTING (XJ)....................8W-44-1
LAMP, IGNITION SWITCH; INTERIOR
LIGHTING (XJ-RHD)................8W-44-1
LAMP, LOW FUEL WARNING;
INSTRUMENT CLUSTER (XJ).........8W-40-1
LAMP, LOW WASHER FLUID WARNING;
INSTRUMENT CLUSTER (XJ).........8W-40-2
LAMP, LOW WASHER FLUID WARNING;
INSTRUMENT CLUSTER (XJ-RHD).....8W-40-2
LAMP, MANUAL TRANSMISSION
UP-SHIFT; INSTRUMENT CLUSTER (XJ) . 8W-40-2
LAMP (MIL), MALFUNCTION INDICATOR;
FUEL/IGNITION (XJ)
................8W-30-5
LAMP (MIL), MALFUNCTION INDICATOR;
FUEL/IGNITION (YJ)
................8W-30-5
LAMP (MIL), MALFUNCTION INDICATOR;
INSTRUMENT CLUSTER (XJ)
.........8W-40-2
LAMP (MIL), MALFUNCTION INDICATOR;
INSTRUMENT CLUSTER (XJ-RHD)
.....8W-40-1
LAMP (MIL), MALFUNCTION INDICATOR;
FUEL/IGNITION (XJ-RHD)
............8W-30-4
JINDEX 15
Description Group-Page Description Group-Page Description Group-Page

TIRE/WHEEL HOLDDOWN AND FLOOR
BRACKETSÐXJ, SPARE...............23-98
TO USE THIS GROUP, HOW; WIRING
DIAGRAMS (XJ)......................8W-1
TO USE THIS GROUP, HOW; WIRING
DIAGRAMS (XJ-RHD)..................8W-1
TO USE THIS GROUP, HOW; WIRING
DIAGRAMS (YJ)......................8W-1
TOOL, DRB SCAN; BRAKES...............5-3
TOOL, DRB SCAN; COOLING SYSTEM......7-5
TOOL, DRB SCAN; EMISSION CONTROL
SYSTEMS...........................25-2
TOOL, DRB SCAN; FUEL SYSTEM........14-54
TOOL, DRB SCAN; IGNITION SYSTEMS....8D-8
TOOLS, TROUBLESHOOTING............8W-4
TOP DOORÐYJ, HALF-METAL SOFT.....23-134
TOP LIFTGATE GLASSÐYJ, HARD......23-124
TOP QUARTER WINDOW GLASSÐYJ,
HARD.............................23-149
TOP REPAIRÐYJ, HARD..............23-127
TOP ROOF VENTÐYJ, HARD..........23-127
TOP SERVICE INFORMATIONÐYJ, SOFT . 23-127
TOP SERVICEÐYJ, SOFT.............23-129
TOPÐYJ, HARD....................23-126
TORQUE; BATTERY/STARTER/
GENERATOR SERVICE..................8B-8
TORQUE; COOLING SYSTEM.............7-46
TORQUE; FUEL SYSTEM...............14-67
TORQUE; IGNITION SYSTEMS............8D-32
TORQUE CONVERTER...........21-167,21-67
TORQUE CONVERTER CLUTCH RELAY....14-65
TORQUE CONVERTER CLUTCH RELAY
TEST..............................14-48
TORQUE CONVERTER CLUTCH
RELAYÐPCM OUTPUT................14-29
TORQUE CONVERTER CLUTCH (TCC)
SOLENOID AND RELAY; FUEL/IGNITION
(XJ).............................8W-30-4
TORQUE CONVERTER CLUTCH (TCC)
SOLENOID AND RELAY;
TRANSMISSION CONTROLS (YJ)......8W-31-1
TORQUE CONVERTER CLUTCH (TCC)
SOLENOID AND RELAYÐ2.5L ENGINE
ONLY; TRANSMISSION CONTROLS (XJ) . 8W-31-1
TORQUE CONVERTER DIAGNOSIS . . 21-86,21-87,
21-88
TORQUE CONVERTER INSTALLATION,
TRANSMISSION.....................21-199
TORQUE CONVERTER REMOVAL,
TRANSMISSION.....................21-198
TORQUE CONVERTER STALL TEST......21-178
TORQUE CONVERTER STATOR CLUTCH
INSPECTION.......................21-199
TORQUE SPECIFICATIONS; CLUTCH.......6-17
TORQUE SPECIFICATIONS; ENGINES . . 9-54,9-95
TORQUE SPECIFICATIONS; EXHAUST
SYSTEM AND INTAKE MANIFOLD........11-10
TORQUE SPECIFICATIONS; FRONT
SUSPENSION AND AXLE................2-49
TORQUE SPECIFICATIONS; HEATING AND
AIR CONDITIONING...................24-37
TORQUE SPECIFICATIONS;
INTRODUCTION............Intro.-11,Intro.-12
TORQUE SPECIFICATIONS; PROPELLER
SHAFTS............................16-15
TORQUE SPECIFICATIONS; REAR
SUSPENSION AND AXLES...............3-51
TORQUE SPECIFICATIONS; STEERING....19-78
TORQUE SPECIFICATIONS, 30RH/32RH . . 21-336
TORQUE SPECIFICATIONS, AW-4.......21-344
TORQUE SPECIFICATIONS, BRAKE........5-70
TORQUE SPECIFICATIONS,
MEASUREMENT...................Intro.-11
TORQUE SPECIFICATIONS, NP231/NP242 . 21-344
TORQUE SPECIFICATIONSÐ
ACCESSORIES......................23-162
TORQUE SPECIFICATIONSÐMANUAL
TRANSMISSION.....................21-333
TORQUE SPECIFICATIONSÐXJ
VEHICLES.........................23-161
TORQUEÐ2.5L.......................8B-8
TORQUEÐ4.0L.......................8B-8
TOUCH-UP, PAINTED SURFACE.........23-158
TOW HOOK, REAR
.....................13-9
TOW HOOKS
........................13-13
TOW HOOKS, FRONT
..................13-7
TOW, TRAILER; TRAILER TOW (XJ)
....8W-54-1
TOW, TRAILER; TRAILER TOW (XJ-RHD)
. 8W-54-1TOWING AND HOISTING, JUMP
STARTING............................0-9
TOWING, FOUR-WHEEL-DRIVE VEHICLE . . . 0-12
TOWING RECOMMENDATIONS...........0-10
TOWING SPECIFICATIONS, TRAILER....Intro.-5,
Intro.-9
TOWING WHEN KEYS ARE NOT
AVAILABLE..........................0-13
TOWINGÐXJ, TWO-WHEEL-DRIVE
VEHICLE............................0-11
(TPS)ÐPCM INPUT, THROTTLE
POSITION SENSOR...................14-25
TRACK BAR; FRONT SUSPENSION AND
AXLE...........................2-11,2-15
TRACK BAR; REAR SUSPENSION AND
AXLES...............................3-8
TRAC-LOK DIFFERENTIAL...............3-45
TRAILER HITCH......................23-77
TRAILER HITCHÐXJ..................23-77
TRAILER TOW; TRAILER TOW (XJ)....8W-54-1
TRAILER TOW; TRAILER TOW (XJ-RHD) . 8W-54-1
TRAILER TOWING SPECIFICATIONS....Intro.-5,
Intro.-9
TRANSFER CASE (4WD VEHICLES).......0-24
TRANSFER CASE ASSEMBLY....21-294,21-319
TRANSFER CASE CHANGES...........21-307
TRANSFER CASE DISASSEMBLY AND
OVERHAUL..................21-289,21-310
TRANSFER CASE IDENTIFICATION......21-284,
21-307
TRANSFER CASE INSTALLATION . . 21-288,21-309
TRANSFER CASE, LEGEND FOR NP231 . . 21-306
TRANSFER CASE, LEGEND FOR NP242 . . 21-332
TRANSFER CASE LUBRICANT AND FILL
LEVEL............................21-284
TRANSFER CASE, NP231.......21-283,21-305
TRANSFER CASE, NP242.......21-307,21-331
TRANSFER CASE REMOVAL.....21-287,21-309
TRANSFER CASE SKID PLATE.......13-15,13-3
TRANSMISSION, 30RH/32RH
AUTOMATIC.........................21-67
TRANSMISSION AND CONVERTER
INSTALLATION......................21-117
TRANSMISSION AND CONVERTER
REMOVAL.........................21-115
TRANSMISSION AND TORQUE
CONVERTER INSTALLATION...........21-199
TRANSMISSION AND TORQUE
CONVERTER REMOVAL...............21-198
TRANSMISSION APPLICATION..........21-67
TRANSMISSION ASSEMBLY AND
ADJUSTMENT............21-265,21-16,21-52
TRANSMISSION ASSEMBLY AND
ADJUSTMENT PROCEDURES..........21-155
TRANSMISSION ASSEMBLY TIPS.......21-155
TRANSMISSION, AUTOMATIC............0-23
TRANSMISSION, AW-4 AUTOMATIC.....21-165
TRANSMISSION, AX 15 MANUAL........21-33
TRANSMISSION, AX 4/5 MANUAL........21-1
TRANSMISSION CASE CLEANING AND
INSPECTION.......................21-125
TRANSMISSION CASE OVERHAUL,
FIRST-REVERSE BRAKE PISTON........21-247
TRANSMISSION CHANGES AND PARTS
INTERCHANGEABILITY................21-67
TRANSMISSION COMFORT SWITCH;
TRANSMISSION CONTROLS (XJ-RHD) . . 8W-31-1
TRANSMISSION CONTROL MODULE;
TRANSMISSION CONTROLS (XJ-RHD) . . 8W-31-1
TRANSMISSION CONTROL MODULE
(TCM) SERVICE.....................21-183
TRANSMISSION CONTROL MODULEÐ
4.0L ENGINE ONLY; TRANSMISSION
CONTROLS (XJ)...................8W-31-1
TRANSMISSION CONTROLS AND
COMPONENTS.......................21-67
TRANSMISSION COOLER FLOW TESTING . 21-113
TRANSMISSION COOLER LINE AND
FITTING SERVICE...................21-111
TRANSMISSION COOLER LINE FITTINGS . 21-197
TRANSMISSION COOLER REVERSE
FLUSHING.........................21-114
TRANSMISSION COOLER SERVICE
......21-196
TRANSMISSION DIAGNOSIS
. 21-78,21-79,21-80,
21-81,21-82,21-83,21-84,21-85
TRANSMISSION DIAGNOSIS, 30RH/32RH
. 21-70
TRANSMISSION DIAGNOSIS, AW-4
.....21-176
TRANSMISSION DISASSEMBLY
. . 21-119,21-201TRANSMISSION DISASSEMBLY AND
OVERHAUL.....................21-37,21-5
TRANSMISSION GEAR RATIOS..........21-34
TRANSMISSION IDENTIFICATION . . 21-166,21-33,
21-67,21-2
TRANSMISSION INSTALLATION.....21-36,21-5
TRANSMISSION LUBRICANT............21-34
TRANSMISSION, MANUAL..............0-22
TRANSMISSION OIL COOLERS...........7-36
TRANSMISSION OVERHAUL, 30RH/32RH . 21-119
TRANSMISSION OVERHAUL, AW-4......21-201
TRANSMISSION RANGE LAMP;
INTERIOR LIGHTING (YJ)............8W-44-1
TRANSMISSION RANGES AND SHIFT
LEVER POSITIONS...................21-166
TRANSMISSION REMOVAL.........21-35,21-3
TRANSMISSION REMOVAL AND
INSTALLATION, 30RH/32RH...........21-115
TRANSMISSION REMOVAL AND
INSTALLATION, AW-4................21-198
TRANSMISSION SHIFT PATTERN........21-34
TRANSMISSION SHIFTER/IGNITION
INTERLOCK MECHANISM, AUTOMATIC....19-55
TRANSMISSION SWITCH AND PLUG
LOCATIONS.........................21-34
TRANSMISSION THROTTLE CABLE
ADJUSTMENT......................21-194
TRANSMISSION THROTTLE CABLE
REPLACEMENT.....................21-193
TRANSMISSION THROTTLE VALVE
CABLE ADJUSTMENT...................21-71
TRANSMISSION, TORQUE
SPECIFICATIONSÐMANUAL...........21-333
TRANSMISSION UP-SHIFT LAMP,
MANUAL; INSTRUMENT CLUSTER (XJ) . 8W-40-2
TRANSMISSION VALVE BODY
INSTALLATION......................21-187
TRANSMISSION VALVE BODY
OVERHAUL........................21-250
TRANSMISSION VALVE BODY REMOVAL . 21-186
TRANSMISSION VALVE BODY
SOLENOIDS........................21-184
TRANSMISSION/TRANSFER CASE
IDENTIFICATION, ENGINE.............Intro.-5
TRANSMISSION/TRANSFER CASE
SPECIFICATIONS....................21-333
TRANSMITÐPCM OUTPUT, SCI.........14-29
TRANSMITTER, KEYLESS ENTRY . 8P-1,8P-7,8P-8
TRAVEL SENSOR, BRAKE PEDAL;
ANTI-LOCK BRAKES (YJ)............8W-32-1
TRAY LAMPÐXJ, I/P ASH RECEIVER.....23-80
TRAYÐXJ, BATTERY
..................23-14
TRAYÐYJ, BATTERY
.................23-110
TREAD WEAR INDICATORS
..............22-3
TRIM COVERSÐXJ, B/C-PILLAR AND
LIFTGATE PILLAR
....................23-88
TRIM PANEL EXTENSIONÐXJ, QUARTER
. 23-87
TRIM PANELÐXJ, DOOR
..............23-31
TRIM PANELÐXJ, FRONT INNER SCUFF
PLATE/COWL SIDE
...................23-86
TRIM PANELÐXJ, LIFTGATE
............23-59
TRIM PANELÐYJ, FULL-METAL DOOR
. . . 23-137
TRIM PANELS AND SCUFF PLATESÐXJ,
INTERIOR
..........................23-84
TRIM PANELSÐXJ, QUARTER AND
WHEELHOUSE
.......................23-87
TRIM REPAIR PRODUCTSÐXJ,
AFTERMARKET PAINT
................23-159
TRIM REPAIR PRODUCTSÐYJ,
AFTERMARKET PAINT
................23-160
TROUBLE CODE (DTC), DIAGNOSTIC
.....14-54
TROUBLE CODE, GENERATOR
DIAGNOSTIC
........................8A-22
TROUBLE CODE, SPEED CONTROL
DIAGNOSTIC
.........................8H-5
TROUBLE DIAGNOSISÐXJ, DOME/
COURTESY LAMP
....................8L-16
TROUBLE DIAGNOSISÐXJ, HEADLAMP
DELAY FUNCTION
....................8L-14
TROUBLE DIAGNOSISÐXJ, LIGHTED
VANITY MIRROR
.....................8L-16
TROUBLE DIAGNOSISÐYJ, DOME/
COURTESY LAMP
....................8L-31
TROUBLESHOOTING TESTS; WIRING
DIAGRAMSÐGENERAL INFORMATION
(XJ)
...............................8W-4
30 INDEXJ
Description Group-Page Description Group-Page Description Group-Page