1995 AUDI A8 ATQ Engine Electronic Engine Power Control Checking Workshop Manual

24-146


Display fields

1 2 3 4
Display group 060: Adaptation of throttle valve control module
Display xx % xx %
x
---
Indicated Throttle
valve angle
(angle
sensor 1) Throttle
valve angle
(angle
sensor 2) Adaptation step counter
Adaptation condition
Functional
range 0 to 100% 0 to 100 %
0 to 8
ADP in progress
ADP OK
ADP ERROR
Specified
value 3 to 93 % 97 to 3 %
8
ADP OK
Notes


After adaptation, the adaptation step
counter reaches the number 8 (it is OK for
numbers to be skipped). If "ADP ERROR." is displayed:
Check DTC memory Page
01
-15
.
If specified value is not
obtained: Note, page
Page 24
-147
.
Note for display field 3:
Different numbers are shown in display field 3 during adaptation that represent the current adaptation condition. It is not
particularly important how the adaptation step counter (display field 3) behaves during adaptation, but rather that display field
Pa
ge 17 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5

4 indicates the specification "ADP OK" after adaptation.
Pa
ge 18 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5

24-147

Note:
The control module can abort adaptation for the
following reasons:

Throttle valve cannot be closed completely (e.g.
contamination)
Battery voltage is too low.
Throttle valve control module or wire connection
is faulty.
Engine is started during adaptation or
accelerator pedal is operated.
Tension of throttle valve housing (check
bolts)
After termination, tester displays "Function is
unknown or cannot be performed at the
moment". The next time the ignition is switched
on (several seconds), adaptation will be
automatically repeated.

- End basic adjustment of the engine by pressing
the key.
Rapid data transfer
HELP

Indicated on display (function selection):
Pa
ge 19 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5

Select function XX
Pa
ge 20 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5

24-148


Angle sensor -1- for throttle drive,
checking

Special Tools and Equipment

VAG1526A
VAG1594A
VAG1598/31
VAS5051 with VAG5051/1
- or
VAG1551 with VAG1551/3B
Pa
ge 21 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5

24-149
Angle sensor 1 for throttle drive (power
accelerator actuation) -G187- and angle sensor 1
for throttle drive (power accelerator actuation) -
G188- inform the Engine Control Module (ECM)
about the position of the throttle valve. Both
angle sensors are located in the throttle valve
control module.

Test sequence

- Connect VAS5051 tester or VAG1551 scan tool
and select the control module for engine
electronics using "address word" 01 Page 01
-
9 .

Ignition must remain switched on for this.Rapid data transfer
HELP
Select function XX

When indicated on display:
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Read Measuring Value Block
Q
Input displa
y group number XXX

When indicated on display:
- Press buttons -0-, -6- and -2- to select "display group number 062" and
press -Q- button to confirm input.
Read Measuring Value Block 62
1
2
3
4

Indicated on display:
- Check specified values for E-gas potentiometer voltages in display
fields 1 and 2.
Pa
ge 22 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5

24-150


Display fields

1 2 3 4
Display group 062: E-Gas potentiometer voltages
Display
xx %
xx % xx % xx %
Indicated
Throttle valve angle
(angle sensor 1) Throttle valve angle
(angle sensor 2) Sensor for
Pedal position Sensor 2 for
Pedal position
Specified value
3 to 93 %
(Idle value:
8 to 18 %) 97 to 3 %
(Idle value:
80 to 90 %) 12 to 97 % 4 to 49 %
Specified value
3 to 93 %
97 to 3 % 12 to 97 % 4 to 49 %
Note:
Engine Control Module (ECM) calculates the
voltage values of the angle sensors in percent
relative to 5 volts and displays these percentage
values. (5 volts supply voltage represents 100
%).

- Observe display field 1 and 2.

- Slowly depress accelerator pedal completely.
Percent indication in display field 1 must rise
uniformly. The tolerance range of 3 to 93% will
Pa
ge 23 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5

not be used completely during this.
Percent indication in display field 2 must
decrease uniformly. The tolerance range of 97 to
3% will not be used completely during this.
Pa
ge 24 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5