1995 AUDI A4 wheel

17-2


Crankcase breather and oil spray jets,
removing and installing

Removing and installing oil pump, oil pan, oil filter
and oil cooler Page 17
-32

1 -
Bolt, tightening torque: 20 Nm
2 -
Washer
3 -
Tensioning roller
4 -
Bolt, tightening torque: 45 Nm
5 -
Idler wheel
For toothed belt
Pa
ge 2 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-39


- Disconnect cable from terminal 30/B+ -1-. Tightening torque: 16 Nm
- Disconnect connector for terminal 50 -2-.
- Remove right wheel

- remove top bolt -1- from right wheel housing. Tightening torque: 65 Nm
- Remove lower bolt (accessible from engine side). Tightening torque: 65
Nm
- Remove starter from front of vehicle.
Pa
ge 41 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-40

Note:
To avoid having to check and adjust wheel
alignment, only loosen the front subframe
mountings and lower the subframe at the front.

- Remove lower section of oil pan.
- Disconnect return lines for turbocharger from upper section of oil pan.

Notes: - Unbolt cover plate -2- for oil pump sprocket.
When loosening bolt -2- securing cover plate, counter-hold at welded
nut. When installing, make sure that the plate engages in position -arrows-.
Pa
ge 42 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-44

- Clean both sealing surfaces for lower section of
oil pan; ensure that they are free of oil and
grease.

Note:
Do not use any adhesive or sealant.

- Install new gasket on lower section of oil pan
and install on upper section of oil pan with two
diagonally opposite bolts.

- Tighten all securing bolts hand-tight.

- Tighten bolts to 10 Nm with torque wrench,
working from center outward.

- Install new seal on oil drain plug and tighten to
30 Nm.

Notes:

When installing the upper section of the oil pan
with the engine removed from the vehicle,
ensure that the oil pan is positioned flush with
the cylinder block at the flywheel end.
The sealant must be left to dry for about 30
minutes after installing the oil pan before engine
Pa
ge 46 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-45

- Fill with coolant Page 19
-19
.

- Fill engine with oil.

Repair Manual, Maintenance


- Install subframe.

Repair Manual, Suspension, Wheels,
Steering, Repair Group 40


- Install lock carrier in normal position.

Repair Manual, Body Exterior, Repair Group
50


- Install bumper.

Repair Manual, Body Exterior, Repair Group
63


Pa
ge 48 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

Repair Manual, Suspension, Wheels,
Steering, Repair Group 40


- Install lock carrier in normal position.

Repair Manual, Body Exterior, Repair Group
50


- Install bumper.

Repair Manual, Body Exterior, Repair Group
63

Pa
ge 58 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-57


- Remove 4 bolts from upper section of oil pan.

- Remove following components before unbolting front sealing flange:
1 - Tensioning roller for toothed belt: 20 Nm
2 - Idler wheel: 45 Nm
3 - Toothed belt tensioner: 10 Nm
4 - Lever for toothed belt tensioner: 20 Nm
Pa
ge 62 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1