1995 AUDI A4 air filter

17-2


Crankcase breather and oil spray jets,
removing and installing

Removing and installing oil pump, oil pan, oil filter
and oil cooler Page 17
-32

1 -
Bolt, tightening torque: 20 Nm
2 -
Washer
3 -
Tensioning roller
4 -
Bolt, tightening torque: 45 Nm
5 -
Idler wheel
For toothed belt
Pa
ge 2 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-8


Oil pump, oil pan, oil filter and oil cooler,
removing and installing

1 -
Bolt for dipstick guide tube
Tightening torque: 25 Nm
2 -
Dipstick guide tube Replace O-ring
3 -
Oil pan - upper section There is no gasket between engine block
and upper section of pan. Only use silicone
sealant D 454 300 A2.
4 -
Hex socket head bolt M8 Tightening torque: 20 Nm
5 -
Hex bolt M6 Tightening torque: 15 Nm
Pa
ge 8 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-10


12 -
Hex bolt M6
Tightening torque: 10 Nm
13 -
Oil pan - lower section
14 -
Hex bolt M6 Tightening torque: 10 Nm
15 -
Retainer for oil lines
16 -
Oil supply line From pump to oil filter
17 -
Oil supply line From oil filter to engine oil system
18 -
O-ring Always replace
Pa
ge 10 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-11


19 -
O-ring
Always replace
20 -
Oil filter
21 -
Hex nut Tightening torque: 30 NmThreaded line for oil cooler and oil filter is
screwed into upper section of pan with 20
Nm tightening torque.
22 -
Oil cooler Ensure O-ring is installed correctly when
installing
23 -
Oil pump Driven off crankshaft via chainTightening torque of chain sprocket to oil
pump: 25 Nm Tightening torque of oil pump to engine
block: 25 Nm
Pa
ge 11 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-36

- Place drip tray VAG 1306 under engine.

- Remove oil filter.

- Release hose clamps -arrows-.
- Remove oil cooler -1-.

- Remove bottom nuts on engine mountings -1- (left and right sides).
- Mark positions of securing points -1- and locating sleeves -2- under
engine mountings on left and right sides.
Pa
ge 38 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1