1994 TOYOTA CAMRY transmission

206
ELECTRONIC CONTROLLED TRANSMISSION AND A/T INDICATOR (5S±FE)
PREVIOUS AUTOMATIC TRANSMISSIONS HAVE SELECTED EACH GEAR SHIFT USING MECHANICALLY CONTROLLED THROTTLE
HYDRAULIC PRESSURE, GOVERNOR HYDRAULIC PRESSURE AND LOCK±UP HYDRAULIC PRESSURE. THE ELECTRONIC
CONTROLLED TRANSMISSION, HOWEVER, ELECTRICALLY CONTROLS THE LINE PRESSURE AND LOCK±UP PRESSURE ETC.,
THROUGH THE SOLENOID VALVE. ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU)
CONTROL OF THE SOLENOID VALVE BASED ON THE INPUT SIGNALS FROM EACH SENSOR MAKES SMOOTH DRIVING POSSIBLE BY
SHIFT SELECTION FOR EACH GEAR WHICH IS MOST APPROPRIATE TO THE DRIVING CONDITIONS AT THAT TIME.
1. GEAR SHIFT OPERATION
DURING DRIVING, THE ENGINE CONTROL MODULE (ECU) SELECTS THE SHIFT FOR EACH GEAR WHICH IS MOST APPROPRIATE TO
THE DRIVING CONDITIONS, BASED ON INPUT SIGNALS FROM THE ENGINE COOLANT TEMP. SENSOR (EFI WATER TEMP. SENSOR)
TO TERMINAL THW OF THE ENGINE CONTROL MODULE (ECU), AND ALSO THE INPUT SIGNALS TO TERMINAL SP1 OF THE ENGINE
CONTROL MODULE (ECU) FROM THE VEHICLE SPEED SENSOR (SPEED SENSOR) DEVOTED TO THE ELECTRONIC CONTROLLED
TRANSMISSION. CURRENT IS THEN OUTPUT TO THE ELECTRONIC CONTROLLED TRANSMISSION SOLENOIDS. WHEN SHIFTING TO
1ST SPEED, CURRENT FLOWS FROM TERMINAL S1 OF THE ENGINE CONTROL MODULE (ECU) " TERMINAL (A)3 OF THE
ELECTRONIC CONTROLLED TRANSMISSION SOLENOIDS " GROUND, AND CONTINUITY TO THE NO. 1 SOLENOID CAUSES THE
SHIFT.
FOR 2ND SPEED, CURRENT FLOWS FROM TERMINAL S1 OF THE ENGINE CONTROL MODULE (ECU) " TERMINAL (A)3 OF THE
ELECTRONIC CONTROLLED TRANSMISSION SOLENOIDS " GROUND, AND FROM TERMINAL S2 OF THE ENGINE CONTROL
MODULE (ECU) " TERMINAL (A)1 OF THE ELECTRONIC CONTROL TRANSMISSION SOLENOIDS " GROUND, AND CONTINUITY TO
SOLENOIDS NO. 1 AND NO. 2 CAUSES THE SHIFT.
FOR 3RD SPEED, THERE IS NO CONTINUITY TO NO. 1 SOLENOID, ONLY TO NO. 2, CAUSING THE SHIFT.
SHIFTING INTO 4TH SPEED (OVERDRIVE) TAKES PLACE WHEN THERE IS NO CONTINUITY TO EITHER NO. 1 OR NO. 2 SOLENOID.
2. LOCK±UP OPERATION
WHEN THE ENGINE CONTROL MODULE (ECU) JUDGES FROM EACH SIGNAL THAT LOCK±UP OPERATION CONDITIONS HAVE BEEN
MET, CURRENT FLOWS FROM TERMINAL SL OF THE ENGINE CONTROL MODULE (ECU) " TERMINAL (B)1 OF THE ELECTRONIC
CONTROLLED TRANSMISSION SOLENOID " GROUND, CAUSING CONTINUITY TO THE LOCK±UP SOLENOID AND CAUSING
LOCK±UP OPERATION.
3. STOP LIGHT SW CIRCUIT
IF THE BRAKE PEDAL IS DEPRESSED (STOP LIGHT SW ON) WHEN DRIVING IN LOCK±UP CONDITION, A SIGNAL IS INPUT TO
TERMINAL B/K OF THE ENGINE CONTROL MODULE (ECU), THE ENGINE CONTROL MODULE (ECU) OPERATES AND CONTINUITY TO
THE LOCK±UP SOLENOID IS CUT.
4. OVERDRIVE CIRCUIT
*O/D MAIN SW ON
WHEN THE O/D MAIN SW IS TURNED ON (O/D OFF INDICATOR LIGHT TURNS OFF), A SIGNAL IS INPUT TO TERMINAL OD2 OF THE
ENGINE CONTROL MODULE (ECU) AND ENGINE CONTROL MODULE (ECU) OPERATION CAUSES GEAR SHIFT WHEN THE
CONDITIONS FOR OVERDRIVE ARE MET.
*O/D MAIN SW OFF
WHEN THE O/D MAIN SW IS TURNED TO OFF, THE CURRENT FLOWING THROUGH THE O/D OFF INDICATOR LIGHT FLOWS
THROUGH THE O/D MAIN SW TO GROUND. CAUSING THE INDICATOR LIGHT TO LIGHT UP. AT THE SAME TIME, A SIGNAL IS INPUT
TO TERMINAL OD2 OF THE ENGINE CONTROL MODULE (ECU) AND ENGINE CONTROL MODULE (ECU) OPERATION PREVENTS
SHIFT INTO OVERDRIVE.
5. ELECTRONIC CONTROLLED TRANSMISSION PATTERN SELECT SW CIRCUIT
IF THE ELECTRONIC CONTROLLED TRANSMISSION PATTERN SELECT SW IS CHANGED FROM NORMAL TO POWER, THE CURRENT
FLOWING THROUGH THE POWER INDICATOR FLOWS TO GROUND, CURRENT FLOWS TO TERMINAL P OF THE ENGINE CONTROL
MODULE (ECU), THE ENGINE CONTROL MODULE (ECU) OPERATES, AND SHIFT UP AND SHIFT DOWN OCCUR AT HIGHER VEHICLE
SPEEDS THAN WHEN THE SW IS IN NORMAL POSITION.
E 7(C), E 8 (B), E10(A)ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU)
(TURN ON THE IGNTION SW)
S1, S2 ±E1 :9.0±14.0 VOLTS WITH SOLENOID ON
0±1.5 VOLTS WITH SOLENOID OFF
P ±E1:7.5±14.0 VOLTS WITH IGNITION SW ON AND PATTERN SELECT SW AT POWER POSITION
L± E1:7.5±14.0 VOLTS WITH SHIFT LEVER AT L POSITION
2± E1:7.5±14.0 VOLTS WITH SHIFT LEVER AT 2 POSITION
R± E1:7.5±14.0 VOLTS WITH SHIFT LEVER AT R POSITION
B/K± E1:9.0±14.0 VOLTS WITH BRAKE PEDAL DEPRESSED
THW± E2:0.2±1.0 VOLTS WITH WITH ENGINE COOLANT TEMP. 60°C (140°F) ±120°C (248°F)
IDL± E2:0±1.5 VOLTS WITH THROTTLE VALVE FULLY CLOSED
9.0±14.0 VOLTS WITH THROTTLE VALVE FULLY OPENED
SYSTEM OUTLINE
SERVICE HINTS

207
VTA±E2:0.3±0.8 VOLTS WITH THROTTLE VALVE FULLY CLOSED
3.2±4.9 VOLTS WITH THROTTLE VALVE FULLY OPENED
VC± E2:4.5±5.5 VOLTS WITH IGNITION SW AT ON POSITION
OD2± E1:9.0±14.0 VOLTS WITH O/D MAIN SW TURNED ON
0±3.0 VOLTS WITH O/D MAIN SW TURNED OFF
IGSW± E1:9.0±14.0 VOLTS WITH IGNITION SW AT ON POSITION
+B± E1:9.0±14.0 VOLTS WITH IGNITION SW AT ON POSITION
+B1± E1:9.0±14.0 VOLTS WITH IGNITION SW AT ON POSITION
M±REL± E1:9.0±14.0 VOLTS WITH IGNITION SW AT ON POSITION
E 2(A), E 3(B)
ELECTRONIC CONTROLLED TRANSMISSION SOLENOID(A)1, (A)3, (B)1±GROUND : EACH 11±15 W
O 5
O/D MAIN SW1±3 : CLOSED WITH O/D MAIN SW OFF, OPEN WITH O/D MAIN SW ON
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C 832E 632N 2A33
C1132E 7C32N 3B33
D 130E 8B32O 533
D 332E10A32P 131
E 2A30J 133S1033
E 3B30J 233T 131
E 430J 333V 531
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A
1D20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1K20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M
2B22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2C22ENGINE WIRE AND J/B NO 2 (ENGINE COMPARTMENT LEFT)2D22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3B
3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
3D
24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
II142COWL WIRE AND INSTRUMENT PANEL WIRE
II242INSTRUMENT PANEL WIRE AND COWL WIRE
IN142INSTRUMENT PANEL WIRE AND SWITCH WIRE
IP144ENGINE WIRE AND COWL WIREIP344ENGINE WIRE AND COWL WIRE
IQ144ENGINE WIRE AND INSTRUMENT PANEL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EB40 (5S±FE)FRONT LEFT FENDER
EC40 (5S±FE)INTAKE MANIFOLD RH
ED40 (5S±FE)INTAKE MANIFOLD LH
IF42LEFT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E1740 (5S FE)ENGINE WIREI1344COWL WIRE
E1840 (5S±FE)ENGINE WIREI1844ENGINE WIRE
I 144COWL WIREI2344COWL WIRE
I 644INSTRUMENT PANEL WIRE
SERVICE HINTS

208
ELECTRONIC CONTROLLED TRANSMISSION AND A/T INDICATOR (5S±FE)

236
COMBINATION METER
AB
IJ1 5IJ111 IJ118
BX1 3 BX1 2 BX1 1 IP3 2
IP3 6
IP1 8IP 3 11 IP314
IP3 5
IP3 161
ED1 A 4
A 8A7A6A 5A12 B 11 B7B10 C 8C7C 4
123
23
4
1 I9
I9 C C
6 FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
R±L
R±L R±L R±L
BRY±L Y±R
BR BR BR Y±L Y±R Y±R
Y±L
BR
BR BR
B Y±G
BY±G
B
P
LG GG±B
G±B G±B
R±W
Y±B Y±BV±Y
R±L JUNCTION
CONNECTOR
BR
BR
FROM E NGINE CONTROL MODULE
(
E NGINE A ND E LE CTRONIC CONTROLLED
TRANSMISSION ECU)(
A/T)
FROM E NGINE CONTROL MODULE
(
ENGINE ECU)(
M/T)
FROM CRUISE CONTROL ECU
SPEEDFUEL
FUEL
WATER TEMP.
TA CHO
ABS
SEAT BELT
OIL
FUEL SENDER
WATER TEMP.
SENDER
IGNITER
VEHICLE SPEED
SENSOR
(
SPEED SENSOR)
TO AB S ECU
TO INTEGRATION
RELAY
OIL P RES SURE
SW
J2
B
W2
I2
V5
O1F1 5C
COMBINATION METER C8 ,C9 , C10
TO BACK±UP LIGHT SW(
M/T)
TO PARK/NEUTRAL POSITION SW
(
NEUTRAL START SW)(
A/T)
TO GENERA TOR(
ALTERNATOR) R±L
R±L
I18 6
TA C
COOLING FAN
ECU C14
BR
B
B JUNCTION CONNECTOR J7
(
*6) (
*6)
(
*7)A
A
(
*7)
(
*6)
1B 6 1D 610A
GAUGE
3D 13
3D 12
1D 121D 13
3C 133C 12

237
*
1 : W/O A/T INDICATOR LIGHT
* 2 : W/ A/T INDICATOR LIGHT
*
3 : MALFUNCTION INDICATOR LAMP
(
CHECK ENGINE WARNING LIGHT)
*7 : 5S±FE *
6 : 1MZ±FE * 5 : TMM MADE
*
4:TMCMADE
AB
C
COMBINATION METER1
IEIF 2 1B 15 B3B9B13
B 12B 8B14 C 1 C 3 A 9A 10C 2
II1 4
11B DE 18 A
FB E D
8 A
FAFROM POWER SOURCE SYSTEM(
SEE PAGE 64)
B±W
R±Y
R±GW±R Y±G B±W
B±O G± L
G±R
R±Y R±Y W±BG±RG± L
±B W±B
R±W R±W
R±W
G±O
Y
B±Y
R±BB±YY G±O R±Y
R±Y
R±W 10A
STARTER
TO LIGHT FAILURE
SENSOR
FROM º HEAD RHº FUSE
FROM º HEAD(
UP R±RH)
ºFUSE
(
CA NADA) (
USA) CRUISE
(
*3)
BRAKE
BULB
CHECK
RE AR LIGHT
O/D OFF
CHARGE
SRS
HIGH BEAM
PKB BRK
TOO/DMAINSW
TO GENERATOR(
ALTERNATOR)
TO CENTER AIRBAG
SENSOR ASSEMBLY
TO DIMMER SW
[COMB. SW] TO CRUISE CONTROL ECU
TO E NGINE CONTROL MODULE
(
ENGINE AND ELECTRONIC CONTROLLED
TRANSMISSION ECU)(
A/T)
TO E NGINE CONTROL MODULE
(
ENGINE ECU)(
M/T)
BRAKE FLUID
LEVEL SWJUNCTION
CONNECTOR
JUNCTION
CONNE CTOR
DAYTIME RUNNING
LIGHT RELAY
(
MAIN) PARKING
BRAKE SW
PARKING
BRAKE SW(
EX. 1MZ±FE A/T)
(
1MZ±FE A/T)
JUNCTION
CONNECTOR
JUNCTION
CONNECTOR (
USA)
(
CANA DA) C8 ,C9 , C10
J2
J2 B2
P3
P2 D4
J2
J3(
*1) (
*1)
(
USA)
II1 2
I6
G±O
G±O G±O
(
*2) FROM A/T
INDICATOR LIGHT
W±B
(
CA NADA)(
*5) (
*5)
O
(
*4)O
(
*4)
4
3B 203C 2
1D 31F3 7. 5A
IGN7. 5A
SRS
3B 19 3D19 3B 83D18
3D 83C8 3A 10
1M 51C 8
W

238
COMBINATION METER* 1 : W/O A/T INDICATOR
AB
A 11 A2A1
A 3
C13 B5 B 16
IGB 4
G
R R RG±B G±YL±R
R±YW±BB B
W±B W±B
GG
FROM ELECTRONIC
CONTROLLED
TRANSMISSION PATT
SELECT SW
FROM HA ZA RD S W(
TR)
FROM HA ZA RD S W(
TL) METER
ILLUMINATION
POWER
TURN RH
TURN LH
OPEN DOOR TO RHEOSTAT
TO DOOR COURTESY SW
COMBINATION METER C8 ,C9 ,C10AI13 II16
TO E NGINE CONTROL
MODULE(
ENGINE AN
ELECTRONIC CONTRO
TRANSMISSION ECU)
L±R
L±R L±R
(
*1)
(
*1)
2G 220A
DOME
G
15A
TA IL
1D 14
3C 4
3D 5
3D 203D 9
1C 5
3A 161C 1
3C 14
1D10
1D11
1L 83C183D 6 1D 2
1M 11C 11
FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
ERN
D
LLED

244
ELECTRONICALLY CONTROLLED HYDRAULIC COOLING FAN (1MZ±FE)
1212
2 3EC1 8
ECEB I18
IP2 7
42 310 9 816 5
6 I18
B±R B±R W±R
LLB
L L±W L±W
L±W
L±R L±R W±BL±YY Y±LBR BR
E SOL+ SOL± TH± TH+ HPIGB TAC IDL FROM POWER SOURCE SYSTEM(
SEEPAGE64)
TO COMBINATION
METERFROM THROTTLE
POSITION SENSOR
FROM ENGINE CONTROL MODULE
(
ENGINE AND ELECTRONIC
CONTROLLED TRANSMISSION ECU)
SOLENOID VALVE
(
FOR HYDRAULIC MOTOR)
ENGINE COOLANT
TEMP. SENSOR
(
WATER TEMP. SENSOR)
(
FOR COOLING FAN)DATA LINK
CONNECTOR 1
(
CHECK
CONNECTOR)A/C SINGLE
PRESSURE SW COOLING FAN ECU C14
S1
E5D1 A2 OPT
3A 153C 16
1A 715A
ECU±IG

248
AIR CONDITIONING (PUSH CONTROL SW TYPE)
5 5
55
1 2
IP1 8EC1 4
IP3 9
IP3 4 I191
4
IR1 5IR16 IR14
5471
4 10 8 9 13 14 12 21
2 R±WR± BR±L
W± BW±R
L±WR±B R±W
W±R
W±L
L±Y
G B±Y LG±BB B BW±B
L± W(
*1)
L±Y
GL±B(
*1)
B± W
L± Y
R±LR± L R±L W±R
R±L
W±R
A/C DUAL
PRESSURE SW
A/C MAGNETIC
CLUTCH AND
LOCK SENSOR
A/C EVAPORATOR
TEMP. SENSOR
A/C MAGNETIC
CLUTCH RELAY
A/C AMPLIFIER
TO ENGINE CONTROL MODULE
(
ENGINE AND ELECTRONIC
CONTROLLED TRANSMISSION
ECU)(
A/T)
OR ENGINE CONTROL MODULE
(
ENGINE ECU)(
M/T) FROM ENGINE CONTROL MODULE
(
ENGINE AND ELECTRONIC
CONTROLLED TRANSMISSION
ECU)(
A/T)
OR ENGINE CONTROL MODULE
(
ENGINE ECU)(
M/T)
IGNITER245
13
W±R
A3A2
A11
A10
I2B±W
(
*
2) TO RADIATOR
FAN RELAY NO. 3E6
B± W
(
*1)
(
*2)
B±W(
*2) W±L(
*2)
TACH6
TAC
(
*2)
B
(
*1)
C14
COOLING FAN
ECU*1 : 1MZ±FE
*
2 : 5S±FE
1B 1
1D 12