1994 TOYOTA CAMRY clutch

70
STARTING AND IGNITION (1MZ±FE)
I12 IGNITION SW
4±7 : CLOSED WITH IGNITION SW AT ST POSITION
10±9 : CLOSED WITH IGNITION SW AT ON OR ST POSITION
STARTER RELAY
(6) 2± (6) 4 : CLOSED WITH CLUTCH START SW ON AND IGNITION SW AT ST POSITION (M/T)
CLOSED WITH IGNITION SW AT ST POSITION (A/T)
STARTER
POINTS CLOSED WITH CLUTCH START SW ON AND IGNITION SW AT ST POSITION
P 1 PARK/NEUTRAL POSITION SW (NEUTRAL START SW) (A/T)
2±3 : CLOSED WITH A/T SHIFT LEVER IN P OR N POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
D 128I15B29I2129
E 732I1629J 733
F10A28I1729P 129
F16B28I1829S 3A29
I 2A29I1929S 4B29
I1233I2029
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
125R/B NO. 1 (LEFT KICK PANEL)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1C
1E20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1G20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M
2C22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2G22COWL WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2H22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2F22COWL WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EF138 (1MZ±FE)EF140 (5S±FE)ENGINE WIRE AND COWL WIRE
IP144
ENGINE WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EC38 (1MZ±FE)INTAKE MANIFOLD RHEC40 (5S±FE)INTAKE MANIFOLD RH
ED38 (1MZ±FE)INTAKE MANIFOLD LHED40 (5S±FE)INTAKE MANIFOLD LH
IG42INSTRUMENT PANEL BRACE LH
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E1038 (1MZ FE)ENGINE WIREE1338 (1MZ FE)ENGINE WIREE1238 (1MZ±FE)ENGINE WIREE1438 (1MZ±FE)ENGINE WIRE
SERVICE HINTS

72
STARTING AND IGNITION (5S±FE)
4
107
9 AM2 AM1ACC
IG1
ST1
IG2
ST2
30A
AM210A
STARTER 40A
MAIN
A 1
B 12C 52F12C2 1
1 2H 22G 1
B1A 1
IG EF1 1EF1 1
M 52 31
2 1
E20 EF1 3B±O
B±W
B±O
B±R
BB±W
W±RW
B±WB W
B±W B±W
B W±BB±R
B
B
B±W B±W
B± R(
M/T)
(
M/T)
(
A/T)
(
A/T)
(
M/T)
(
A/T) W±B
4 5
P
N
65
W
B B
W±BB±R
W±B
B±R
PARK/NEUTRAL POSITION SW
(
NE UTRA L START SW)
(
A/T) P1CLUTCH START
SW(
M/T) C7
STARTER
RELAY IGNITION SW I12
FL MAIN
2. 0L
BATTERY
TO CIRCUIT OPENING
RELAY TO ENGINE CONTROL
MODULE(
ENGINE AND
ELE CTRONIC CO NTROLLED
TRANSMISSION
ECU(
A/T)
,
ENGINE ECU(
M/T))
B S3 ,S4A
B F10 , F16A
STARTER
FUSE BOX100A ALT
IP 1 17
1G 6
1E 5
140A
AM1
1E 11G 9
2
3B 20 3D23C 2
3C 18
1M 13C 6
1C 11

74
STARTING AND IGNITION (5S±FE)
I12 IGNITION SW
4±7 : CLOSED WITH IGNITION SW AT ST POSITION
10±9 : CLOSED WITH IGNITION SW AT ON OR ST POSITION
C 7 CLUTCH START SW (M/T)
1±2 : CLOSED WITH CLUTCH PEDAL FULLY DEPRESSED
STARTER RELAY
(6) 2± (6) 4 : CLOSED WITH CLUTCH START SW ON AND IGNITION SW AT ST POSITION (M/T)
CLOSED WITH IGNITION SW AT ST POSITION (A/T)
STARTER
POINTS CLOSED WITH CLUTCH START SW ON AND IGNITION SW AT ST POSITION
P 1 PARK/NEUTRAL POSITION SW (NEUTRAL START SW) (A/T)
2±3 : CLOSED WITH A/T SHIFT LEVER IN P OR N POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C 732E11B32I1233
D 130F10A30P 131
D2A30F16B30S 3A31D 2B30I 231S 4B31
E 7A32I 331
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
125R/B NO. 1 (LEFT KICK PANEL)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A
1C
1E20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1G
20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M
2C22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2F22COWL WIRE AND J/B NO 2 (ENGINE COMPARTMENT LEFT)2G22COWL WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2H22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3B
3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
3D
24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EF138 (1MZ±FE)EF140 (5S±FE)ENGINE WIRE AND COWL WIRE
IP144
ENGINE WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EC38 (1MZ±FE)INTAKE MANIFOLD RHEC40 (5S±FE)INTAKE MANIFOLD RH
IG42INSTRUMENT PANEL BRACE LH
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E1640 (5S FE)ENGINE WIREE2040 (5S±FE)ENGINE WIRE
E1940 (5S±FE)ENGINE WIRE
SERVICE HINTS

192
CRUISE CONTROL
B
ST1 IG1 ACC
AM1
7
IP3 8IP3 11
II1 4 2 1
1 1 213 41883
17 15
20 1420 510 2
13B 4 B 12 B5B9 A 6
1 2
IG CC
I13
11 R±L R±L
R±L
W±B
W±B W±B
B±R B±W
R±L B±W
B±R B
B
W±B
W±L
W
LG±R
R±W LG±R
R±W LG±R
R±W
R±WW±B
W±B
G±BG
V±Y
G±Y V±YP LG B
FROM POWER SOURCE SYSTEM(
SEEPAGE64)
10A
GAUGE
COMBINATON METER
DIODE
(
FOR CRUISE
CONTROL)VEHICLE
SPEED SENSOR
(
SPEED SENSOR)
DATA LINK CONNECTOR 2
(
TDCL)
A/D JUNCTION
CONNECTOR
CRUISE CONTROL
CLUTCH SW
(
M/T)
CRUISE CONTROL SW
[COMB. SW]
DA TA LINK CONNE CTOR 1
(
CHECK CONNECTOR)
PARKING
BRAKE SW
PARKING
BRAKE SWMAIN
CA NCELSET/
COAST RE SUME/
ACCEL N&C GND CMS CCS TC PKBBSPD PI
TC
IGNITION SW
P
N5
6EF1 1
B±W B±W
J1
P1
D5
C8 , C9
D3
V5A
PARK/NEUTRAL POSITION SW
(
NE UTRAL S TA RT SW)
(
A/T) B
TO STARTER RELAY
CRUIS E CONTROL ECU C16
C15
C13
D1
P3
P2
(
1MZ±FE)
SPEED
CRUISEI12
IP3 2
(
A/T)
(
5S±FE)IP3 14
(
A/T)
(
M/T) (
M/T)
R±L
TO BA CK ±UP LIGHT SW(
M/T)
TO PARK/NEUTRAL POSITION SW
(
NE UTRA L S TA RT SW)(
A/T)
TO GENERATOR(
ALTERNATOR)
R±L
I18
(
*2) O
(
*1)
G±L
(
*2) O
(
*1)
O
(
*1) G±L
(
*2)
1G 63C16
1A 14 3B16 1E 5
1A 71D61B6 15A
ECU±IG
3D 22 3B8
3B 10 3B19 3B9
3B 73B18
3B 17
3B 14 3B5
3C 18
1M1
1C11
3B 12
3D 83C83B 15
3D 16

196
CRUISE CONTROL
CURRENT IS APPLIED AT ALL TIMES THROUGH STOP FUSE TO TERMINAL 1 OF THE CRUISE CONTROL ECU AND TERMINAL 2 OF
STOP LIGHT SW, AND ALSO THROUGH THE STOP FUSE TO TERMINAL 15 OF CRUISE CONTROL ECU.
WITH THE IGNITION SW TURNED TO ON, THE CURRENT FLOWS THROUGH GAUGE FUSE TO TERMINAL (A) 6 OF COMBINATION
METER AND THE CURRENT THROUGH ECU±IG FUSE FLOWS TO TERMINAL 14 OF CRUISE CONTROL ECU.
WHEN THE IGNITION SW IS ON AND THE CRUISE CONTROL MAIN SW IS TURNED ON, A SIGNAL IS INPUT FROM TERMINAL 15 OF
CRUISE CONTROL MAIN SW TO TERMINAL 4 OF CRUISE CONTROL ECU. AS A RESULT, THE CRUISE CONTROL ECU FUNCTIONS
AND THE CURRENT TO TERMINAL 14 OF CRUISE CONTROL ECU TO TERMINAL 13 OF CRUISE CONTROL ECU " GROUND, AND
THE CRUISE CONTROL SYSTEM IS IN A CONDITION READY FOR OPERATION.
AT THE SAME TIME, THE CURRENT THROUGH THE GAUGE FUSE FLOWS FROM TERMINAL (A) 6 OF CRUISE CONTROL INDICATOR
LIGHT " TERMINAL (B) 9 " TERMINAL 5 OF CRUISE CONTROL ECU " TERMINAL 13 " TO GROUND, CAUSING THE CRUISE
CONTROL INDICATOR LIGHT TO LIGHT UP, INDICATING THAT THE CRUISE CONTROL IS READY FOR OPERATION.
1. SET OPERATION
WHEN THE CRUISE CONTROL MAIN SW IS TURNED ON AND THE SET SW IS TURNED ON WITH THE VEHICLE SPEED WITHIN THE
SET LIMIT (APPROX. 40 KM/H, 25 MPH TO 200 KM/H, 124 MPH), A SIGNAL IS INPUT TO TERMINAL 18 OF THE CRUISE CONTROL ECU
AND THE VEHICLE SPEED AT THE TIME THE SET SW IS RELEASED IS MEMORIZED IN THE ECU AS THE SET SPEED.
2. SET SPEED CONTROL
DURING CRUISE CONTROL DRIVING, THE ECU COMPARES THE SET SPEED MEMORIZED IN THE ECU WITH THE ACTUAL VEHICLE
SPEED INPUT INTO TERMINAL 20 OF THE CRUISE CONTROL ECU FROM THE VEHICLE SPEED SENSOR (SPEED SENSOR), AND
CONTROLS THE CRUISE CONTROL ACTUATOR TO MAINTAIN THE SET SPEED.
WHEN THE ACTUAL SPEED IS LOWER THAN THE SET SPEED, THE ECU CAUSES THE CURRENT TO THE CRUISE CONTROL
ACTUATOR TO FLOW FROM TERMINAL 12" TERMINAL 6 OF CRUISE CONTROL ACTUATOR "TERMINAL 7 "TERMINAL 11 OF
CRUISE CONTROL ECU. AS A RESULT, THE MOTOR IN THE CRUISE CONTROL ACTUATOR IS ROTATED TO OPEN THE THROTTLE
VALVE AND THE THROTTLE CABLE IS PULLED TO INCREASE THE VEHICLE SPEED. WHEN THE ACTUAL DRIVING SPEED IS HIGHER
THAN THE SET SPEED, THE CURRENT TO CRUISE CONTROL ACTUATOR FLOWS FROM TERMINAL 11 OF ECU "TERMINAL 7 OF
CRUISE CONTROL ACTUATOR "TERMINAL 6 "TERMINAL 12 OF CRUISE CONTROL ECU.
THIS CAUSES THE MOTOR IN THE CRUISE CONTROL ACTUATOR TO ROTATE TO CLOSE THE THROTTLE VALVE AND RETURN THE
THROTTLE CABLE TO DECREASE THE VEHICLE SPEED.
3. COAST CONTROL
DURING THE CRUISE CONTROL DRIVING, WHILE THE COAST SW IS ON, THE CRUISE CONTROL ACTUATOR RETURNS THE
THROTTLE CABLE TO CLOSE THE THROTTLE VALVE AND DECREASE THE DRIVING SPEED. THE VEHICLE SPEED WHEN THE COAST
SW IS TURNED OFF IS MEMORIZED AND THE VEHICLE CONTINUES AT THE NEW SET SPEED.
4. ACCEL CONTROL
DURING CRUISE CONTROL DRIVING, WHILE THE ACCEL SW IS TURNED ON, THE CRUISE CONTROL ACTUATOR PULLS THE
THROTTLE CABLE TO OPEN THE THROTTLE VALVE AND INCREASE THE DRIVING SPEED.
THE VEHICLE SPEED WHEN THE ACCEL SW IS TURNED OFF IS MEMORIZED AND THE VEHICLE CONTINUES AT THE NEW SET
SPEED.
5. RESUME CONTROL
UNLESS THE VEHICLE SPEED FALLS BELOW THE MINIMUM SPEED LIMIT (APPROX. 40 KM/H, 25 MPH) AFTER CANCELING THE SET
SPEED BY THE CANCEL SW, PUSHING THE RESUME SW WILL CAUSE THE VEHICLE TO RESUME THE SPEED SET BEFORE
CANCELLATION.
6. MANUAL CANCEL MECHANISM
IF ANY OF THE FOLLOWING OPERATIONS OCCURS DURING CRUISE CONTROL OPERATION, CURRENT FLOW TO MAGNETIC
CLUTCH OF THE ACTUATOR IS CUT TURNS OFF AND THE MOTOR ROTATES TO CLOSE THE THROTTLE VALVE AND THE CRUISE
CONTROL IS RELEASED.
*PLACING THE SHIFT LEVER IN ªNº POSITION (PARK/NEUTRAL POSITION SW (NEUTRAL START SW ON). ªSIGNAL INPUT TO
TERMINAL 2 OF ECUº (A/T)
*DEPRESSING THE CLUTCH PEDAL (CLUCH SW ON). ªSIGNAL INPUT TO TERMINAL 2 OF THE ECUº (M/T)
*DEPRESSING THE BRAKE PEDAL (STOP LIGHT SW ON). ªSIGNAL INPUT TO TERMINAL 16 OF ECUº
*PUSH THE CANCEL SW (CANCEL SW ON). ªSIGNAL INPUT TO TERMINAL 18 OF ECUº
*DEPRESSING THE PARKING BRAKE PEDAL (PARKING BRAKE SW ON). ªSIGNAL INPUT TO TERMINAL 3 OF ECUº (3VZ±FE)
*PULLING THE PARKING BRAKE LEVER (PARKING BRAKE SW ON). ªSIGNAL INPUT TO TERMINAL 3 OF THE ECUº (5S±FE)
SYSTEM OUTLINE

197
7. AUTO CANCEL FUNCTION
A) IF ANY OF THE FOLLOWING OPERATING CONDITIONS OCCURS DURING CRUISE CONTROL OPERATION, THE SET SPEED IS
ERASED, CURRENT FLOW TO MAGNETIC CLUTCH IS CUT OFF AND THE CRUISE CONTROL IS RELEASED. (MAIN SW TURNS OFF).
WHEN THIS OCCURS, THE IGNITION SW MUST BE TURNED OFF ONCE BEFORE THE MAIN SW WILL TURN ON AGAIN.
*OVER CURRENT TO TRANSISTOR DRIVING MOTOR AND/OR MAGNETIC CLUTCH.
*WHEN CURRENT CONTINUED TO FLOW TO THE MOTOR INSIDE THE ACTUATOR IN THE THROTTLE VALVE ªOPENº DIRECTION.
*OPEN CIRCUIT IN MOTOR AND/OR MAGNETIC CLUTCH.
*MOMENTARY INTERRUPTION OF VEHICLE SPEED SIGNAL.
*SHORT CIRCUIT IN CRUISE CONTROL SW.
*MOTOR DOES NOT OPERATE DESPITE THE MOTOR DRIVE SIGNAL BEING OUTPUT.
B) IF ANY OF THE FOLLOWING CONDITIONS OCCURS DURING CRUISE CONTROL OPERATION, THE SET SPEED IS ERASED AND
THE CRUISE CONTROL IS RELEASED. CURRENT FLOW TO MAGNETIC CLUTCH IS CUT OFF UNTIL THE SET SW IS ªONº AGAIN.)
*WHEN THE VEHICLE SPEED HAS FALLEN BELOW THE MINIMUM SPEED LIMIT, APPROX. 40 KM/H (25 MPH)
*WHEN THE VEHICLE SPEED HAS FALLEN MORE THAN 16 KM/H (10 MPH) BELOW THE SET SPEED, E.G. ON AN UPWARD SLOPE.
*WHEN POWER TO THE CRUISE CONTROL SYSTEM IS MOMENTARILY CUT OFF.
C) IF ANY OF THE FOLLOWING CONDITIONS OCCURS DURING CRUISE CONTROL OPERATION, THE CRUISE CONTROL IS
RELEASED.
*OPEN CIRCUIT FOR TERMINAL 1 OF CRUISE CONTROL ECU.
8. AUTOMATIC TRANSMISSION CONTROL FUNCTION
*IN OVERDRIVE. IF THE VEHICLE SPEED BECOMES LOWER THAN THE OVERDRIVE CUT SPEED (SET SPEED MINUS APPROX. 4
KM/H, 2.5 MPH) DURING CRUISE CONTROL OPERATION, SUCH AS DRIVING UP A HILL, THE OVERDRIVE IS RELEASED AND THE
POWER INCREASED TO PREVENT A REDUCTION IN VEHICLE SPEED.
*AFTER RELEASING THE OVERDRIVE, IF VEHICLE SPEED BECOMES HIGHER THAN THE OVERDRIVE RETURN SPEED (SET
SPEED MINUS APPROX. 2 KM/H, 1.2 MPH) AND THE ECU JUDGES BY THE SIGNALS FROM POTENTIOMETER OF THE ACTUATOR
THAT THE UPWARD SLOPE HAS FINISHED, OVERDRIVE IS RESUMED AFTER A WHILE.
C 2 CRUISE CONTROL ACTUATOR
1±3 : APPROX. 2 K

5±4 : APPROX. 38

C13 CRUISE CNTROL SW MAIN [COMB. SW]
15±20 : CONTINUITY WITH MAIN SW ON
20±17 : APPROX. 418
WITH CANCEL SW ON
APPROX. 68
WITH RESUME/ACCEL SW ON
APPROX. 198
WITH SET/COAST SW ON
C16 CRUISE CONTROL ECU
14±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
1,15±GROUND : ALWAYS APPROX. 12 VOLTS
3±GROUND : CONTINUITY WITH PARKING BRAKE SW ON (ONE OF THE CANCEL SW) OR BRAKE LEVEL WARNING SW ON
20±GROUND :4 PULSE WITH 1 ROTATION OF ROTOR SHAFT
18±GROUND : APPROX. 418
WITH CANCEL SW ON IN CONTROL SW
APPROX. 68
WITH RES/ACC SW ON IN CONTROL SW
APPROX. 198
WITH SET/COAST SW ON IN CONTROL SW
13±GROUND : ALWAYS CONTINUITY
2±GROUND : CONTINUITY WITH SHIFT LEVER AT N POSITION (A/T) OR CLUTCH PEDAL DEPRESSED (M/T)
SERVICE HINTS

198
ELECTRONIC CONTROLLED TRANSMISSION AND A/T INDICATOR (1MZ±FE)
A
2D 22C32D4 2B 2
I23
I18
2 1
EBED IP 1 18 IP1 11 IP312
D 7 D 24 D 14 D 22 D 23
A 27 A11 A17 A33 B4
26FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
P±L P±LV L±Y W±B
B±O
B±OB±O
W±L
G±W G±W
Y±BW±GB±OR±Y
W±L Y±L W±BB±O
15A
EFI
SL S1 S2 E02 NC2± +B +B1 BATT STP OD1EFI MAIN
RELAY
FROM
CRUIS E CONTROL ECU
BR P±L
TO CRUISE
CONTROL ECU
15 23
O/D DIRECT CLUTCH
SPEED SENSOR O6STOP LIGHT SW
G±R
G±W
2 1
S10
B 1 A 2
B 2B1NOISE FILTER
(
FOR STOP LIGHT) N2 ,N3 A
G±W
G±R
B E7 ,E8AC,E9
ENGINE CONTROL MODULE(
ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU)
B±O
D ,E10
A
3
ELECTRONIC CONTROLLED
TRANSMISSION SOLENOID E2 4 A
1
J UNCTION
CONNECTOR J7
A 3SLN±
Y±GB±O
B±OB±O
W±B
W±B
BR
A 34E01
A 28E03
A 16E1
B 9NC2+
Y±L
W±B
1D 91M3 7. 5A
IGN15A
STOP
1A 15
3B 43C 191M 6

242
RADIATOR FAN AND CONDENSER FAN (5S±FE)
2B 12E82B32E6
55 55
55 55 2G 6
2E5
1 2EA1 1
M
1 2M
1 2
E5 5
EB EB
W±B W±B B±R B±R L±B
B±R
L
B W±B
W±R R WB±O B±R
W±B W±B
L
B±R
BW±BW±B
B±W
OM POWER SOURCE SYSTEM(
SEE PAGE 64)
30A
RDI FAN
24 13
4
FROM A/C
MAGNETIC
CLUTCH RELAY RADIATOR
FAN RELAY
RADIATOR
FAN RELAY
NO. 2
RADIATOR
FAN RELAY
NO. 3
A/C SINGLE
PRESSURE SW
WATER
TEMP. SW
(
FOR COOLING
FA N)RADIATOR
FAN MOTORA/C CONDE NSE R
FAN MOTOR A1
A2
R1
E532 51 15 23
3 2
EA1 2
1A 7FR
15A
ECU±IG
3A 153C 16
2B 40A
CDS FAN
3