1994 TOYOTA CAMRY relay

170
UNLOCK AND SEAT BELT WARNING
5 1
1
2 1
1 2 2G 2
IO1 5IO1 2 CC
6
7
IGBL
R±W
R R±L W± B
R±G
R±Y R±Y
R±Y W±B W±B
W±B W±B
R±L R±LFROM POWER SOURCE SYSTEM(
SEE PAGE 64)
20A
DOME
SEAT BELT
WARNING LIGHT
[COMB. METER]JUNCTION
CONNECTOR
UNLOCK
WARNING SW
[IGNITION SW]
DOOR COURTESY
SW FRONT LHBUCKLE
SWBUCKLE
SW J1
C9
I12
D12 B 7 B 8
(
W/ POWER SEAT)
(
W/O POWER SEAT) W±B
C C
C
JUNCTION
CONNECTOR J5
W± B
(
S/D, C/P)
W±B
(
S/D, C/P)(
W/G) (
W/ G)
1B6
1C 7
1G 21H21H51C 1
TIMERBUZZER 97110A
GAUGE
INTEGRATION RELAY
10 5 6 8
1M 11G 4

171
CURRENT ALWAYS FLOWS TO TERMINAL 1 OF THE INTEGRATION RELAY THROUGH THE DOME FUSE.
1. SEAT BELT WARNING SYSTEM
WHEN THE IGNITION SW IS TURNED ON, CURRENT FLOWS FROM THE GAUGE FUSE TO THE TERMINAL 7 OF THE INTEGRATION
RELAY AT THE SAME TIME, CURRENT FLOWS TO TERMINAL 9 OF THE RELAY FROM THE GAUGE FUSE THROUGH THE SEAT BELT
WARNING LIGHT. THIS CURRENT ACTIVATES THE SEAT BELT WARNING RELAY AND, CURRENT FLOWING THROUGH THE WARNING
LIGHT FLOWS FROM TERMINAL 9 OF THE RELAY" TERMINAL 10 " GROUND, CAUSING THE WARNING LIGHT TO LIGHT UP. AT THE
SAME AS THE WARNING LIGHT LIGHTS UP. A BUCKLE SW OFF SIGNAL IS INPUT TO TERMINAL 8 OF THE RELAY, THE CURRENT
FLOWING TO TERMINAL 1 OF THE RELAY FLOWS FROM TERMINAL 10 " GROUND AND THE SEAT BELT WARNING BUZZER SOUNDS
FOR APPROX. 4±8 SECONDS. HOWEVER, IF SEAT BELT IS PUT ON DURING THIS PERIOD (WHILE THE BUZZER IS SOUNDING),
SIGNAL INPUT TO TERMINAL 8 OF THE RELAY STOPS AND THE CURRENT FLOW FROM TERMINAL 1 OF THE RELAY " TERMINAL 10
" GROUND IS CUT, CAUSING THE BUZZER TO STOP.
2. UNLOCK WARNING SYSTEM
WITH THE IGNITION KEY INSERTED IN THE KEY CYLINDER (UNLOCK WARNING SW ON), THE IGNITION SW STILL OFF AND DOOR
OPEN (DOOR COURTESY SW ON), WHEN A SIGNAL IS INPUT TERMINAL 5 AND 6 OF THE RELAY, THE INTEGRATION RELAY
OPERATES, CURRENT FLOWS FROM TERMINAL 1 OF THE RELAY " TERMINAL 10 " GROUND AND THE UNLOCK WARNING
BUZZER SOUNDS.
B 7, B 8 BUCKLE SW
1±2 : CLOSED WITH DRIVR'S LAP BELT IN USE
D12 DOOR COURTESY SW FRONT LH
1±GROUND : CLOSED WITH FRONT LH DOOR OPEN
INTEGRATION RELAY
10±GROUND : ALWAYS CONTINUITY
6±GROUND : CONTINUITY WITH FRONT LH DOOR OPEN
5±GROUND : CONTINUITY WITH IGNITION KEY IN CYLINDER
8±GROUND : CONTINUITY UNLESS DRIVER'S LAP BELT IN USE
9±GROUND :0 VOLTS WITH IGNITION SW ON AND BUCKLE SW OFF
1±GROUND : ALWAYS APPROX. 12 VOLTS
7±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
I12 UNLOCK WARNING SW [IGNITION SW]
1±5 : CLOSED WITH IGNITION KEY IN CYLINDER
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
B 732D1234 (S/D), 35 (C/P), 36 (W/G)J 536 (W/G)
B 832I1233
C 932J 133
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B
1C20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1G
20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1H20FLOOR NO. 1 WIRE J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
2E22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IO142FLOOR NO. 1 WIRE AND SEAT WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IG42INSTRUMENT PANEL BRACE LH
46 (S/D)
BL48 (C/P)UNDER THE LEFT QUARTER PILLARBL
50 (W/G)
UNDER THE LEFT QUARTER PILLAR
SYSTEM OUTLINE
SERVICE HINTS

173
HORN
10
11
G±B
G±W
G±W FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
HORN SW
[COMB. SW]
HORN
LHHORN
RH C12
H5 H6
2G 52A3 10A
HORN
HORN
RELAY
13 2
HORN RELAY
2±3 : CLOSED WITH HORN SW ON
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C1232H 528 (1MZ±FE), 30 (5S±FE)H 628 (1MZ±FE), 30 (5S±FE)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
2A22ENGINE ROOM MAIN WIRE AND J/B NO 2 (ENGINE COMPARTMENT LEFT)2E22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
1 BLACK BLACK C12 H 5, H 6
XXX
X
10
SERVICE HINTS

184
FRONT WIPER AND WASHER
M365 IR1 16 IR115 IR114
IEI5
OFF
MIST
INT
LOW
HIGH
WASHER
L
FROM POWER SOURCE SYSTEM(
SEEPAGE64)
8
4 16
13 7
18
L±O
L±B
L
L±YW±B
L±OL±B
L±Y FRONT WIPER AND WASHER SW(
W/ WIPER RELAY)
[COMB. SW]
FRONT W IP ER MOTOR F9 C13
2IR111
M 12
E1
L L
L
L±W L
WASHER MOTOR W1 L±W
L
12 C13BLACKW1BLACK F9BLACK
IR1 17
EA 1
W±B
X78X
XX
1618 X 4X X
13 X123
6 5 X
1M 220A
WIPER

185
WITH THE IGNITION SW TURNED ON, THE CURRENT FLOWS TO TERMINAL 18 OF THE WIPER AND WASHER SW, TERMINAL 2 OF
THE WASHER MOTOR AND TERMINAL 4 OF THE WIPER MOTOR THROUGH THE WIPER FUSE.
1. LOW SPEED POSITION
WITH WIPER SW TURNED TO LOW POSITION, THE CURRENT FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW "
TERMINAL 7 " TERMINAL 3 OF THE WIPER MOTOR " WIPER MOTOR " TERMINAL 1 " TO GROUND AND CAUSES TO THE WIPER
MOTOR TO RUN AT LOW SPEED.
2. HIGH SPEED POSITION
WITH WIPER SW TURNED TO HIGH POSITION, THE CURRENT FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW "
TERMINAL 13 " TERMINAL 2 OF THE WIPER MOTOR " WIPER MOTOR " TERMINAL 1 " TO GROUND AND CAUSES TO THE WIPER
MOTOR TO RUN AT HIGH SPEED.
3. INT POSITION
WITH WIPER SW TURNED TO INT POSITION, THE RELAY OPERATES AND THE CURRENT WHICH IS CONNECTED BY RELAY
FUNCTION FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW " TERMINAL 16 " TO GROUND. THIS FLOW OF CURRENT
OPERATES THE INTERMITTENT CIRCUIT AND THE CURRENT FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW "
TERMINAL 7 " TERMINAL 3 OF THE WIPER MOTOR " TERMINAL 1 " TO GROUND AND THE WIPER FUNCTIONS.
THE INTERMITTENT OPERATION IS CONTROLLED BY A CONDENSER'S CHARGED AND DISCHARGED FUNCTION INSTALLED IN
RELAY AND THE INTERMITTENT TIME IS CONTROLLED BY A TIME CONTROL SW TO CHANGE THE CHARGING TIME OF THE
CONDENSER.
4. WASHER CONTINUOUS OPERATION
WITH WASHER SW TURNED TO ON, THE CURRENT FLOWS FROM TERMINAL 2 OF THE WASHER MOTOR " TERMINAL 1 "
TERMINAL 8 OF THE WIPER AND WASHER SW " TERMINAL 16 " TO GROUND AND CAUSES TO THE WASHER MOTOR TO RUN AND
WINDOW WASHER TO JET. THIS CAUSES THE CURRENT TO FLOW TO WASHER CONTINUOUS OPERATION CIRCUIT IN TERMINAL 18
OF THE WIPER AND WASHER SW " TERMINAL 7 " TERMINAL 3 OF THE WIPER MOTOR " TERMINAL 1 " TO GROUND AND THE
WIPER FUNCTION.
C13 FRONT WIPER AND WASHER SW (W/ WIPER RELAY) [COMB. SW]
16±GROUND : ALWAYS CONTINUITY
18±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
7±GROUND : APPROX. 12 VOLTS WITH WIPER AND WASHER SW AT LOW OR MIST POSITION
APPROX. 12 VOLTS 2 TO 12 SECONDS INTERMITTENTLY WITH WIPER SW AT INT POSITION
4±GROUND : APPROX. 12 VOLTS WITH IGNITION SW ON UNLESS WIPER MOTOR AT STOP POSITION
13±GROUND : APPROX. 12 VOLTS WITH WIPER AND WASHER SW AT HIGH POSITION
F 9 FRONT WIPER MOTOR
5±6 : CLOSED UNLESS WIPER MOTOR AT STOP POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C1332F 928 (1MZ±FE), 30 (5S±FE)W 128 (1MZ±FE), 30 (5S±FE)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1H20FLOOR NO. 1 WIRE J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IR144ENGINE ROOM MAIN WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EA38 (1MZ±FE)FRONT RIGHT FENDEREA40 (5S±FE)FRONT RIGHT FENDER
IE42LEFT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E138 (1MZ±FE)ENGINE ROOM MAIN WIREI 544COWL WIREE 140 (5S±FE)ENGINE ROOM MAIN WIRE
SYSTEM OUTLINE
SERVICE HINTS

186
REAR WIPER AND WASHER
IR118
IR117
M 23
IJ1 4IJ114 IJ18
Bc3 8Bc36Bc37
Bd1 6Bd18Bd17I7
B36
M 14
BL IE L L±O L±O
L
L
L
L
L±O
P±B
P±G
W±B L±O L±O
P±B
P±G W±B W±B
W±BL±WL±Y
L±WL±Y
L±WL±YLL L
21 72 1 10 16
3 4
C 863
C FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
JUNCTION
CONNECTOR J5
REAR WIPER
MOTOR R18 REA R WIPER RELAY R19WASHER MOTOR W1REAR WIPER AND WASHER SW
[COMB. SW] C13
OFF
INT
ON
WASHER WASHER
P±G
(
CANADA)
BR 2
W±B
(
US A)
1H 15 1M2 WIPER
20A

187
WHEN THE IGNITION SW IS TURNED ON, CURRENT FLOWS TO TERMINAL 2 OF WASHER MOTOR, TERMINAL 4 OF REAR WIPER
RELAY AND TERMINAL 1 OF REAR WIPER MOTOR THROUGH THE WIPER FUSE.
1. REAR WIPER NORMAL OPERATION
WITH THE IGNITION SW TURNED ON AND REAR WIPER AND WASHER SW TURNED ON, THE CURRENT FLOWING TO TERMINAL 4
OF REAR WIPER RELAY FLOWS TO TERMINAL 6 OF RELAY " TERMINAL 1 OF REAR WIPER AND WASHER SW " TERMINAL 16 "
TO GROUND. THUS, THE RELAY COIL IS ACTIVATED AND THE CURRENT TO TERMINAL 4 OF RELAY FLOWS TO TERMINAL 1 "
TERMINAL 4 OF REAR WIPER MOTOR " MOTOR " TERMINAL 2 " TO GROUND AND CAUSES THE MOTOR TO OPERATE THE
WIPER.
2. REAR WIPER INTERMITTENT OPERATION
WITH THE IGNITION SW TURNED ON AND REAR WIPER AND WASHER SW TURNED TO INT POSITION, THE CURRENT FLOWING TO
TERMINAL 4 OF REAR WIPER RELAY FLOWS TO TERMINAL 3 OF RELAY " TERMINAL 10 OF WIPER SW " TERMINAL 16 " TO
GROUND. AS A RESULT, THE RELAY OPERATES AND CURRENT FLOWS FROM TERMINAL 4 OF RELAY " TERMINAL 1 " TERMINAL
4 OF REAR WIPER MOTOR " MOTOR " TERMINAL 2 " TO GROUND, CAUSING THE MOTOR TO ROTATE TO OPERATE THE WIPER.
AT THIS TIME THE CONTACT IN THE WIPER MOTOR CLOSED AND THE CURRENT FLOWS FROM TERMINAL 1 OF REAR WIPER
MOTOR " TERMINAL 3 " TERMINAL 2 OF REAR WIPER RELAY " TERMINAL 1 " TERMINAL 4 OF REAR WIPER MOTOR "
TERMINAL 2 " TO GROUND.
THUS, THE INTERMITTENT±STOP CIRCUIT OPERATES, THE CONDENOR IN THE CIRCUIT CHARGES AND THE WIPER CONTINUES TO
OPERATE UNTIL REACHING THE STOP POSITION. AFTER THE WIPER STOPS, CURRENT DOES NOT FLOW TO THE
INTERMITTENT±STOP CIRCUIT FROM TERMINAL 2 OF RELAY, BUT THE CONDENSER DISCHARGES CURRENT INTO THE
INTERMITTENT CIRCUIT AND THE CIRCUIT OPERATES UNTIL THE CONDENSER DISCHARGE ENDS. AS A RESULT, THIS DISCHARGE
INTERVAL BECOMES THE INTERMITTENT TIME.
WHEN THE CURRENT IS DISCHARGED COMPLETELY, THE CURRENT FLOWING TO TERMINAL 4 OF RELAY FLOWS TO TERMINAL 3
" TERMINAL 10 OF REAR WIPER AND WASHER SW " TERMINAL 16 " TO GROUND.
THEN, THE CURRENT IN TERMINAL 4 OF RELAY FLOWS FROM TERMINAL 1 " TERMINAL 4 OF MOTOR " MOTOR " TERMINAL 2 "
TO GROUND AND ROTATES THE MOTOR. THROUGH REPEITION OF THIS PROCESS, INTERMITTENT OPERATION OF THE REAR
WIPER OCCURS.
3. WASHER OPERATION
WITH THE IGNITION SW ON AND THE REAR WIPER AND WASHER SW IS TURNED STRONGLY (WASHER SW ON), CURRENT FLOWS
FROM TERMINAL 2 OF WASHER MOTOR " TERMINAL 3 " TERMINAL 2 OF REAR WIPER AND WASHER SW " TERMINAL 16 " TO
GROUND SO THAT THE WASHER MOTOR ROTATES AND WINDOW WASHER EJECTS THE SPRAY, ONLY THE WHILE THE REAR
WASHER SW IS TURNED, WHEN THE REAR WIPER SW IS OFF, AND THE REAR WIPER AND WASHER SW IS THEN TURNED IN THE
OFF DIRECTION, WASHER LIQUID WILL ALSO SPLAY.
R19 REAR WIPER RELAY
4±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
7±GROUND : ALWAYS CONTINUITY
1±4 : POINTS CHANGES EVERY APPROX. 9±15 SECONDS INTERMITTENTLY WITH IGNITION SW ON AND WIPER SW AT
INT POSITION
W 1 WASHER MOTOR
2±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
3±GROUND : CONTINUITY WITH WASHER SW TURNED ON
SYSTEM OUTLINE
SERVICE HINTS

191
DEFOGGER RELAY
5±3 : CLOSED WITH IGNITION SW ON, DEFOGGER SW ON
R 5 REAR WINDOW DEFOGGER SW
3±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
2±GROUND : ALWAYS CONTINUITY
3±6 : CONTINUITY WITH DEFOGGER SW ON
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
J 233R16A34 (S/D), 35 (C/P), 36 (W/G)R17B34 (S/D), 35 (C/P), 36 (W/G)
R 533R16C34 (S/D), 35 (C/P), 36 (W/G)R17D34 (S/D), 35 (C/P), 36 (W/G)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1C20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1D20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1H20FLOOR NO. 1 WIRE J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
Bc150 (W/G)BACK DOOR NO. 1 WIRE AND FLOOR NO. 1 WIRE
Bd350 (W/G)BACK DOOR NO. 1 WIRE AND BACK DOOR NO. 2 WIRE
Be150 (W/G)REAR WINDOW NO. 1 WIRE AND BACK DOOR NO. 2 WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IE42LEFT KICK PANEL
IG42INSTRUMENT PANEL BRACE LH
BN46 (S/D)UNDER THE RIGHT QUARTER PILLARBN48 (C/P)UNDER THE RIGHT QUARTER PILLAR
BS50 (W/G)BACK DOOR RIGHT
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I 744COWL WIRE
A
F F FX2
36 J2 R 5 R16 ,R17B DARK GRAYBLACK BLUE
(
HINT : SEE PAGE 7)11D R16 , R17CBLACK
SERVICE HINTS