1994 Oldsmobile Cutlass Supreme Owner's Manuals

I
Reverse
R (Reverse): Use this gear to back up.
r
~~
NOTICE:
Shifting to R (Reverse) while your
vehicle is moving forward could
damage your transaxle. Shift to
R
only after your vehicle is stopped.
To rock your vehicle back and forth to
get
out of snow, ice or sand without
damaging your transaxle, see the
Index
under If You're Stuck: In Sand, Mud,
Ice
or Snow.
63

I I'
I

Features & Controls
NOTICE:
Don’t drive in 2 (Second Gear) for
more than
5 miles (8 km) , or at
speeds over
55 mph (88 kwh), or
you can damage your transaxle.
Use
D or 3 as much as possible.
Don’t
shift into 2 unless you are
going slower than
65 mph (105
krn/h), or you can damage your
engine.
1 (First Gear): This position gives you
even more power (but lower fuel
economy) than
2. You can use it on
very steep hills, or in deep snow
or
mud. If the shift lever is put in 1, the
transaxle won’t shift into first gear until
the vehicle is going slowly enough.
NOTICE:
If your front wheels can’t rotate,
don’t
try to drive. This might
happen if you were stuck in very
deep sand or mud or were up
against a solid object. You could
damage your transaxle.
Also, if you stop when going uphill,
don’t hold your vehicle there with
only the accelerator pedal. This
could overheat and damage the
transaxle. Use your brakes or shift
into
P (Park) to hold. your vehicle.
in position on a hill.
Parking Brake
The parking brake uses the brakes on
.the rear wheels.
To Set the Parking Brake:
Hold thexegular brake pedal down with
your right .foot. Push down the parking
brake pedal with your left foot. If the
ignition is
on, the brake system warning
light will come on.

Features & Controls
68
* Move the lever up as far as it will go.
3. Move the ignition key to Lock.
4. Remove the key and take it with you.
If you can walk away from your
vehicle with the ignition Bey in your
hand, your vehicle is in
P (Park).
Console Shiff
1. Hold the brake pedal down with your
right foot and set the parking brake.
2. Move the shift lever into the P (Park)
position like this:
Hold in the button on the lever.
Push the lever all the way toward
the front of your vehicle.
3. Move the ignition key to Lock.
4. Remove the key and take it with you.
If you can walk away from your
vehicle with the ignition key in your
hand, your vehicle is in
P (Park).
Leaving Your Vehicle With the
Engine
Rumina
If you have to leave your vehicle with
the engine running, be sure your vehicle
is in
P (Park) and your parking brake is
firmly set before you leave it. After
you’ve moved the shift lever into the
P (Park) position, hold the regular
brake pedal down. Then, see if you can
move the shift lever away from
P (Park)
without first pulling it toward you (or,
if
you have the console shift lever,
withwt first pushing the button). If you

can, it means that the shift lever wasn’t
fully locked into
P (Park).
Torque Lock
If you are parking on a hill and you
don’t shift your transaxle into
P (Park)
properly, the weight of the vehicle may
put too much force on the parking pawl
in the transaxle. You-may find it
difficult to pull the shift lever out.of
P
(Park). This is called “torque lock.” To
prevent torque lock, set the parking
brake and then shift into
P (Park)
properly before you leave the driver’s
seat.
To find out how, see Shifting Into.
P (Park) in the.Index.
When you are ready to drive; move the
shift lever out of
P (Park) BEFORE you
release the parking brake.
If “torque lock” does occur, you may
need to have another vehicle push yours
a little uphill to take some of the
pressure from the transaxle,
so you can
pull the shift lever out of
P (Park).
Parking Over Things .That
Burn Engine Exhaust
L
69

W?unning.bur Engine’ While
bu’re Parked
It’s better not to park with the engine
running.
But if you ever have to, here
are some things to lmow.
Follow the proper steps to be sure
your
vehicle won’t move. See Shifting Into P
(Park) in the Index.
If you are parking on a hill and if you’re
pulling a trailer, also. see
Towing a
Trailer in the Index.