1994 OLDSMOBILE BRAVADA wheel

2. Reach inside, and unscrew the wing
nut at the center
of the wheel.
Remove it and the hold-down plate
just behind the wing nut. Lift the tire
off the mounting shoe and remove
the cover.
Also remove the bolt
hooked to the ring inside the jack
storage compartment.
3. Open the jack storage compartment 4. Unscrew the wing nut and remove
by lifting the latch and removing the
the jack and wheel wrench. Proceed
cover. to step
5.
153
ProCarManuals.com

Problems on the Road
154
If You Have a Tailgate-Mounted
Spare Tire:
1. Open the jack storage compartment
by lifting the latch and removing the
cover.
2. Unscrew the wing nut and remove
the jack and wheel wrench.
I I I
3. Outside the vehicle, make sure the
spare tire carrier arm is fully latched
to the tailgate. Unzip the tire cover
and
push it back.
ProCarManuals.com

4. Use the wheel wrench to remove the
wheel nuts that secure the tire to the
carrier. Then lift the tire
off the
mounting bracket.
For Both Mounting Systems:
5. Put the spare tire near the flat one.
6. Using the Torx@ head wrench
supplied with the vehicle and stored
in the glove
box, remove the wheel
nut cover.
7. Using the wheel wrench, loosen all tht
wheel nuts. Don’t remove them yet.
155
ProCarManuals.com

Problems on the Road
156
8. Rotate the jack handle cloclwise to
raise the jack head
a little.
9. There is a hole in the vehicle’s frame
for the head of the jack to fit into,
near the wheel to be removed.
Position the jack there.
10. Raise the vehicle by rotating the
jack handle cloclwise. Raise the
vehicle far enough off the ground
so
there is enough room for the spare
tire to fit.
NOTICE:
Raising your vehicle with the jack
improperly positioned will damage
the vehicle or may allow the vehicle
to fall off the jack. Be sure to fit the
jack
lift head into the proper
location before raising your vehicle.
11. Remove all wheel nuts and take off
the flat tire.
12. Remove any rust or dirt from the
wheel bolts, mounting surfaces and
spare wheel. Place the spare on the
wheel mounting surface.
ProCarManuals.com

13. Replace the wheel nuts with the
rounded end
of the nuts toward the
wheel. Tighten each nut by hand
until the wheel is held against the
hub.
14. Lower the vehicle by rotating the
jack handle countercloclnvise.
Lower the jack completely. 15. Tighten the wheel nuts firmly in a
crisscross sequence as shown.
157
ProCarManuals.com

Problems on the Road
158
I
16. Replace the wheel nut cover on the
spare wheel. Be sure to insert the
pin on the wheel cover into the hole
in the wheel. Screw the cover in
place using the TorxB head wrench.
17. Lower the jack head completely by
rotating the jack handle
counterclockwise. If you have an
inside-mounted spare tire, return
the jack and wheel wrench to their
storage compartment and secure
them with the wing nut. Replace the
jack storage compartment cover.
18. Fasten the flat tire where the spare
was stored. If you have a tailgate-
mounted spare tire carrier, tighten
firmly. Push and pull to make sure it
is not loose.
As soon as possible,
tighten the nuts to 22-32 pound-feet
(30-40
Nom) torque.
I If You’re Stuck: In Sand,
Mud, Ice or Snow
19. If you have a tailgate-mounted spare
tire, return the jack and wheel
wrench to their storage
compartment and replace the jack
storage compartment cover. Insert
the cover tabs into the trim panel,
align the cover and fasten the latch. What
you
don’t want to do when your
vehicle is stuck is to spin your wheels.
The method known as “rocking” can
help you get out when you’re stuck, but
you must use caution.
ProCarManuals.com

NOTICE:
Spinning your wheels can destroy
parts
of your vehicle as well as the
tires.
If you spin the wheels too fast
while shifting your transmission
back and forth, you can destroy
your transmission.
Rocking Your Vehicle to Get it Out:
First, turn your steering wheel left and
right. That will clear the area around
your front wheels. Then shift back and
forth between
R (Reverse) and a
forward gear, spinning the wheels as
little as possible. Release the accelerator
pedal while you shift, and press lightly
on the accelerator pedal when the
transmission
is in gear. If that doesn’t
get you out after a few tries, you may
need
to be towed out. If you do need to
be towed out, see
Towing Your Truck
in the Index.
159
ProCarManuals.com

Service & Appearance Care
I
1 74
After adding fluid, recheck the fluid
level as described under
How to
Check.
obtained, push the dipstick back in all
the way.
When the correct fluid level is
I Rear Axle
When to Check and Change
Lubricant
Refer to the Maintenance Schedule to
determine how often to check the
lubricant and when to change it. See
Scheduled Maintenance Services in
the
Index.
How to Check Lubricant
If the level is below the bottom of the
filler plug hole, you’ll need to add some
lubricant. Add enough lubricant to
raise the level to the bottom of the filler
plug hole.
What to Use
Refer to the Maintenance Schedule to
determine what kind of lubricant to use.
See
Recommended Fluids E. Lubricants
in the Index.
I All-Wheel Drive
Transfer Case
When to Check Lubricant
Refer to the Maintenance Schedule to
determine how often to check the
lubricant. See
Periodic Maintenance
Inspections
in the Index.
How to Check Lubricant
If the level is below the bottom of the
filler plug hole, you’ll need to add some
lubricant. Add enough lubricant to
raise the level to the bottom of the filler
plug hole.
What to Use
Refer to the Maintenance Schedule to
determine what kind of lubricant to use.
See
Recommended Fluids G Lubricants
in the Index.
Front Axle
When to Check and Change
Lubricant
Refer to the Maintenance Schedule to
determine how often to check the
lubricant and when to change it. See
Scheduled Maintenance Services in the
Index.
How to Check Lubricant
If the level is below the bottom of the
filler plug hole, you’ll need to add some
lubricant. Add enough lubricant to raise
the level to the bottom of the filler plug
hole.
What to Use
Refer to the Maintenance Schedule to
determine what kind of lubricant to use.
See
Recommended Fluids G Lubricants
in the Index.
I Engine Coolant
The following explains your cooling
system and how to add coolant when it
is low. If you have a problem with
engine overheating, see
Engine
Overheating
in the Index.
The proper coolant for your Oldsmobile
will:
Give freezing protection down to
Give boiling protection up to 258°F
Protect against rust and corrosion.
Help keep the proper engine
-34°F (-37°C).
(125°C).
temperature.
I
ProCarManuals.com