1994 MAZDA MX-5 relay

:-2 .BACK-UP LIGHTS .HORN .STOPLIGHTS .HIGH-MOUNT STOPLIGHT MAIN FUSE BLOCK MAIN BUB TRAOE NUMBER ma-u~ LIGHTS: 11% (~WI Ix-oal OoA FUSE BLOCK \ ,, HIGH-HOUNT STOPLIGHT: 921 (l8.4W) STOP STRIGHTS: 1157 (27Wl PARK/NEUTRAL W/R (F) << IX-MI 15* FUSE BLOCK W/G IF) 0 F-O2k=zz& hORN RELAY F-03 G/O (F) STOR IGHT -5t SWITCH F-03 BACK-LP G/R LIGHT SWITCH OATA LINK PASSENGER-SIOE CONNECTOa (F) AIR BAG MOOWE (SECTION U! R/G (F) z:zzzz::zzzz:zz: G/R IF) F-0.551 HORN 0RIVE;I-SIOE AIR BAG MOOULE . E-19 E-20 A B B (R) (Rl A - VW REAR COnsINATION LIGHT F-05 HORN (F) F-06 PASSENGER-SIDE AIR BAG MXIULE(F) I U j-03 ORIVER-SIOE S-W PASSENGER-SIOE A:R BAG nrrmE (F) AIR BAG MX)UE (F) Gartner Banana

MAIN FUSE @LOCK MAIN EUE TRADE NUMBER W (F) EACX-uP LIGHTS: 1156 (2%) Ix-oal FUSE BLOCK U ,, HIGH-MOUNT STOPLIGHT: Q1 (18.4W) STOP STCRIMTS: 1157 (27WI PARK/NEUTRAL W/R (F) - SWITCH OoA [X-031 Ix-olll 15A (SECTION H-1) FUSE ELDCK WG (F) 1 MTER 0 L (Fl HORN RELAY G/O (F) STOPLIGHT -12 SWITCH OWERTRAIN ONTROL ACK-UP G/R IGHT AT DATA LINK PASSENGER-SIDE CONNECTW RUISE CONTROL UNIT AIR BAG MOOVLE (SECTION U) m38 ::::s::t::z:::== R/G IF) t G/R G/O t I (F) (Fl G T I R/G G I I (R) (R) R/G G [R) (R) (R) 0, WW REAR COMBINATION LIGHT .BACK-UP LIGHTS .HORN .STOPLIGHTS 1 HIGH-MOUNT STOPLIGHT 1 :-06 PASSENGER-SIOE AIR 8AG HOOULE (F) U i-04 PASSENGER-SIDE AIR BAG MOWLE (F) Gartner Banana

LIGHTING SYSTEM - -- -- Troubleshooting I Symptom: Taillights, side marker lights, and license plate lights do not illuminate. 45UOTX-141 Step 1 1. Check TAIL 15A fuse. 2. If the fuse is burned, replace it. Check and, if necessary, repair the wiring harness. 3. If the fuse is OK, go to Step 2. Step 2 1. Turn the headlight switch ON. 2. Measure the voltage at the following terminal wires of the - TNS relay connedor. B+: Battery positive voltage - Terminal 1 Voltage 1 Action I B+ I Go to Step 3 C (WIL) Other I Check D terminal B+ Other Go to Step 4 Check A terminal A (WIR) Step 3 1. Check the bulbs of each light. 2. If the bulb is burned, replace the bulb. 3. If the bulbs are OK, repair wiring harness between the TNS relay and the body ground of each light. B (WIR) B+ Other Check B terminal Repair wiring harness (TAIL 15A fuse - TNS relay) B+ Other Replace TNS relay Repair wiring harness (TAIL 15A fuse - TNS relay) Gartner Banana

LIGHTING SYSTEM TNS RELAY Step 4 1. Disconnect the negative battery cable. 2. Remove the knee protector. 3. Disconnect the combination switch connector. 4. Check for continuity between the following terminals of the combination switch. m: Continuity 5. If not as specified, replace the combination switch. 6. If correct, repair the wiring harness. (TNS relay - combination switch) Removal 1 Installation Remove and install as shown in the figures. raillights Parking lights 3ide marker lights License plate lights Gartner Banana

MAIN FUSE BLOCK FUSE BLOCK C-2 6 PMRmAIN L/R CONTROL MMULE (ENGINE1 (YCTIaN 0-1cl .CIGARETTE LIGHTER .INTERIOR LIGHT .REAR WINDOW OEFROSTER INSTRUMENT WINCmW DEFROSTER WOR SWITCHES (SECTIDN TI -05 REAR WINX)W DEFROSTER RELAY(R) -00 CIGARETTE LIGHTER (I) I-m REAR (R) -REAR NO. 2 (~21 11-07 REAR W INWW DEFROSTER IR21 1-09 INTERIOR LIGHT (I1 E-10 REAR WINOOW DEFROSTER SWITCH (It 1 Gartner Banana

T HORN HORN STRUCTURAL VIEW 1. Horn T-84 2. Horn relay 3. Horn switch Gartner Banana

T HORN Symptom: Horn does not sound. 05UOTX-191 Step 1 1. Check the STOP 15A fuse. 2. If the fuse is burned, replace it. Check and repair the wire harness, if necessary. 3. If the fuse is OK, go to Step 2. Step 2 1. Disconnect the horn connector. 2. Apply battery positive voltage to the horn, and check if the horn sounds. 3. If the horn sounds, go to Step 3. 4. If the horn does not sound, replace the horn. Step 3 1. Remove the knee protector. 2. Ground the terminal B (GIO) of the horn relay connector. 3. If the horn sounds, go to Step 4. 4. If the horn does not sound, go to Step 6. Step 4 1. Disconnect the negative battery cable. 2. Remove the air bag module. (Refer to page T-204.) 3. Check for continuity between the terminal of the horn switch connector and the steering shaft. I OFF I No I Horn switch ON 4. If correct, go to Step 5. 5. If not as specified, replace the horn switch and steering wheel as an assembly. Verify that the air bag system is operating normally by monitoring the air bag warning light. Continuity Yes Gartner Banana

HORN T Step 6 1. Ground the terminal B (GIO) of the horn relay connector. 2. Measure the voltage at the following terminal wires of the horn relay connector. Step 5 1. Remove the knee protector. 2. Disconnect the clock spring connector. 3. Check for continuity of the clock spring connector as shown in the figure. B+: Batterv ~ositive voltaae Continuity Yes No A (WIG) Actlon Repair wiring harness (Horn relay - Clock spring connector) Replace combination switch D (WIG) Voltage B+ Repair wiring harness Other I (STOP l5A fuse - Horn relay) Action Check D terminal Other B+ Repair wiring harness (STOP 15A fuse - Horn relay) Check C terminal REMOVAL I INSTALLATION Horn Remove and install as shown in the figure. Horn Switch 1. Disconnect the negative battery cable. u C (GIR) '+ Other Repair wiring harness (Horn relay - Horn) Replace horn relay Gartner Banana