1994 MAZDA MX-5 transmission

CLUTCH UNIT H 97-1 02 {O&-10.5,71-75.9) 18--26 {I .6-2.7,14-19) (MORI WHITE TA No.2 OR EQUIVALENT ORGANIC MOLYBDENUM GREASE) 1. Clutch release cylinder 2. Transmission Service ..................... section J 3. Boot 4. Clutch release collar Inspection ................. page H-17 5. Clutch release fork 6. Clutch cover Removal Note ............. page H-16 Inspection ................. page H-17 Installation Note ........... page H-17 7. Clutch disc Removal Note ............. page H-16 Inspection ................. page H-17 Installation Note ........... page H-17 8. Pilot bearing Inspection ................. page H-18 Removal Note ............. page H-16 Installation Note ........... page H-16 9. Flywheel Removal Note ............. page H-16 Inspection ................. page H-18 Installation Note ........... page H-16 Gartner Banana

Before beginning any service procedure. refer to section T of this manual for air bag system service warnings and audio antitheft system alarm conditions . MANUAL TRANSMISSION INDEX ....................................... J- 2 ..................................... OUTLINE J- 3 SPECIFICATIONS ........................... J- 3 ........................ STRUCTURAL VIEW J- 4 ............................. COMPONENTS J- 5 ............................. POWER FLOW J- 6 TROUBLESHOOTING GUIDE .................. J- 7 .......................... TRANSMISSION OIL J- 8 ............................... INSPECTION J- 8 ............................ REPLACEMENT J- 8 TRANSMISSION .............................. J- 9 ............................. PREPARATION J- 9 REMOVAL .................................. J-10 DISASSEMBLY ............................. J-13 ............................... INSPECTION 5-23 ASSEMBLY ................................. J-26 INSTALLATION ............................. J-45 25UOJX-011 Gartner Banana

J INDEX INDEX OIL SPECIFICATION API SERVICE GL-4 OR GL-5 ALL-SEASON TYPE: SAE 75W-90 ABOVE 10°C {50°F): SAE 80W-90 CAPACITY. 2.0 L {2.1 US qt, 1.8 Imp qt} 1. Transmission Removal . . . . . . . . . . . . . . . . . . . . page J-10 Disassembly . . . . . . . . . . . . . . . . page J-13 Inspection . . . . . . . . . . . . . . . . . . . page J-23 Assembly . . . . . . . . . . . . . . . . . . . page J-26 Installation . . . . . . . . . . . . . . . . . . page J-45 Gartner Banana

OUTLINE OUTLINE SPECIFICATIONS Transmission Item M15M-D Synchronization mechanism Forward: Synchromesh Reverse: Synchromesh Shift type Gear ratio I st 2nd 5-speed, floor shift 3.1 36 1.888 5th Reverse 0.81 4 3.758 API service GL-4 or GL-5 SAE 75W-90 SAE 80W-90 Grade ' Capacity L {US qt, Imp qt} Viscosity 2.0 12.1, 1.8) All-season Above 10°C {50°F) 45UOJX401 Gartner Banana

OUTLINE J COMPONENTS 1. Front cover 6. 1 st12nd shift fork and rod 11. Countershaft 2. Transmission case 7. 3rdl4th shift fork and rod 12. 5th gear u 3. Intermediate housing 8. Mainshaft gear assembly 13. Reverse gear 4. Extension housing 9. Main drive gear 14. Counter 5th gear 5. 5thlReverse shift fork and 10. Bearing housing assembly 15. Counter reverse gear rod Gartner Banana

J TRANSMISSION OIL TRANSMISSION OIL INSPECTION 1. Remove check plug 0. u 2. Verify that the oil is at the bottom of the check plug hole. If it is low, add the specified oil from check plug @. 3. Wipe the plug clean and apply sealant to the plug threads before installing. Tightening torque @: 25--39 N.m (2.5--4.0 kgf.m, 19-28 ft4bf) REPLACEMENT 1. Remove plugs @I (with washer) and @. 2. Drain the oil into a suitable container. 3. Wipe all plugs clean. 4. Install drain plug @I (with new washer). Tightening torque @: 40-58 N.m (4.0-4.0 kgf.m, 2943 ftlbf) 5. Add the specified oil from check plug 0 port until the level reaches the bottom of check plug hole. Specified oil: API service GL-4 or GL-5 All-season: SAE 75W-90 Above 10°C (50°F): SAE 80W-90 Capacity: 2.0 L (2.1 US qt, 1.8 Imp qt) 6. Apply sealant to threads of plug 0. 7. lnstall plug @. Tightening torque @: 25--39 N.m (2.54.0 kgf.m, 19-28 ft-lbf) Gartner Banana

TRANSMISSION J TRANSMISSION 49 0839 425C Puller set, bearing For removal of bearing For installation of bearing Installer, bearing For removal of clutch hub assembly For holding mainshaft Puller, fan pulley boss Holder, mainshaft For removal of locknut 49 0862 350 Guide, shift fork / For installation of interlock pin Wrench, mainshaft locknut 49 HOl7 101 Hook For removal of bearing 49 071 0 520 Puller, bearing For removal of bearing For removal of transmission case For installation of bearing Pusher, main drive shaft \-4 I Installer, bearing 49 F401 330B Installer set, bearing For installation of bearing For installation of spring and ball Guide, interlock <-- pin For installation of clutch hub assembly 49 8025 OAO Installer, oil seal For installation of dust seal For installation of oil seal 49 6025 001 Body (Part of 49 6025 OAO) For installation of oil seal Handle (Part of 49 8025 OAO) Gartner Banana

J TRANSMISSION REMOVAL 1. Obtain the code number and deactivate the audio antitheft system before disconnecting the battery. (Refer to section T.) 2. is connect the negative battery cable. 3. On level grand, jack up the vehicle and support it evenly on safety stands. 4. Drain the transmission oil into a suitable container. 5. Remove in the order shown in the figure, referring to Removal Note. I. Shift lever knob ?. Rear console 9. Clutch release cylinder 10. Starter I 1 3. Shift lever 11. speedometer cable 4. Undercover 12. Power plant frame (PPF) 5. Performance rod Removal Note ............... page J-1 1 6. Differential mounting pipe 13. Transmission 7. Exhaust pipe J Removal Note ............... page J-12 8. Propeller shaft Service ...................... section L Gartner Banana