ZF Automatic Transmissions Service Manual
Problem Possible Cause
2.3.6 Fault Finding Chart (continued)
e Action
Starter will not operate Rotary
switch faulty or incorrect setting. Rectify
or renew.
3rive not transmitted (neutral
:ondition)
Vehicle moves
Slipping and juddering at start Rotary
switch wiring fault. Rectify 'A'Clutch seized Renew
transmission
Checksecurity System
Harsh engagement
'N'-'D'(under 1500RPM engine
speed)
No 1st to 2nd upshift or 2nd to
1st downshift
No upshift 1st to 2nd
No upshift 2nd to 3rd or
downshift 3rd to 2nd
No upshift 2nd to 3rd
3il filter dirty.
Main pressure control valve seized.
Low oil level.
'A'Clutch faulty.
'D'Clutch one-way clutch slips. ~
'A'Clutch faulty
Low oil level.
'A'Clutch faulty.
'A'Clutch damper faulty (5).
Throttle pot. volts high.
Rotary switch faulty
/ out of adjustment.
MVI wire earthed(remains in 2nd gear).
MVI faulty.
Control circuit fault.
Shift valve
1-2 seized.
Pressure reducing valve
1 seized.
Speed sensor or connectors faulty.
Clutches
'Cl' and 'C' faulty
MV2 wire earthed (remains in 2nd gear).
MV2 faulty.
Shift valve 2
-3 seized.
Speed sensor faulty.
'B'Clutch faulty Clean
/ replace
filter.
Renew valve block.
Check oil level.
Renew transmission.
Renew transmission.
Renew transmission.
Check oil level.
Renew transmission.
Renew valve block.
Check throttle pot. volts.
Rectify or renew.
Renew harness.
Renew valve block.
Check TCM Diagnostics
/ rectify.
Renew valve block.
Renew valve block.
Check connections, rectify or
renew.
Renew transmission
Renew harness.
Renew valve block.
Renew valve block.
Rectify or renew.
Renew transmission
Issue 1 August 1994 63
ZF Automatic Transmissions Service Manual
0
3il in bell housing
2.3.6 Fault Finding Chart (continued)
Oil pump seal leaking.
Oil pump 0
-ring leaking.
Pump housing leaking.
Converter seam leaking.
Problem Possible Cause Action
:onverter clutch
-eakage between gearbox and
sump
Leakage between intermediate
date and gearbox
Leakage at harness plug
:onnector
Leakage at drive flange
:Iutch engagement speed
ncorrect
Loose fastening screws.
Sump gasket faulty.
Bell housing to gearbox screws loose
Connector 'O'ring faulty
Rear oil seal faulty
ingagement
too hard
Jo clutch engagement
Ionverter clutch engaging at
dle (engine will not idle in
'D')
Control circuit fault.
Speed sensor faulty.
Valve body problem.
Converter unit faulty
Control circuit fault
MV3 faulty.
Converter clutch valve seized.
Converter faulty. Pressure reducing valve
1 seized.
Incorrect oil level.
Oil filter not sealing.
Control circuit fault.
MV3 faulty.
MV3 wire earthed.
Converter clutch valve
sticking.
Check TCM Diagnostics / rectify
fault.
Check TCM Diagnostics
1 renew
speed sensor.
Renew valve body
Renew converter unit
Check TCM Diagnostics
1 rectify
fault.
Renew valve block.
Renew valve block.
Renew converter.
Renew valve block.
Check oil level.
Check 0
-ring etc.
Check TCM Diagnostics
/ rectify
fault.
Renew valve block.
Renew harness.
Renew valve block.
Renew oil pump seal.
Renew 0
-ring.
Renew oil pump.
Renew converter.
Torque tighten.
Renew gasket.
Torque tighten
Renew
'0' ring
Renew oil seal
Issue 1 August 1994 66
. _.~ -
