1994 JAGUAR XJ engine

AJ16 Engine Service Manual
4.29 Oil Pick-up Strainer, Renew
SRO 12.60.20
1 Remove the oil pan, see Section 4.27.
1 Remove the bolts securing the rear windage tray (1 Fig. 1) to the cylinder block and remove the tray.
1 Remove the three bolts (2 Fig. 1) securing the strainer and
remove the strainer (3 Fig. 1).
1 Clean all components and examine for damage and wear.
Apply sealant to the replacement strainer, and
fit and se- cure to the housing with the bolts. See Service Materials
in the Preliminary Pages.
1 Refittherear windagetraytothecylinder blockand secure
with the bolts.
1 Refit the oil pan, see Section 4.27.
Fig. 1
Issue 1 August 1994 49

AJ16 Engine Service Manual
4.30
SRO 12.60.56
Remove the oil pan, see Section 4.27.
Remove oil pressure relief valve screw cap (1 Fig. 1) and
collect spring (2 Fig.
I), valve (4 Fig. I), and mandrel (3 Fig. 1).
Check the valve spring and mandrel for wear, scoring or pitting, renew if damaged.
Measure the components against the specifications listed in Service Data in the Preliminary Pages.
If any of the components are suspect, they must be re- newed.
. Lubricate and assemble the mandrel, spring and valve.
Fit and tighten the relief valve screw cap.
. Refit the oil pan, see Section 4.27.
Oil Pressure ReYief Valve AssemblB Renew
1116.1
Fig. 1
Issue 1 August 1994 50

AJ16 Engine Service Manual
4.31 Oil Pump, Renew
SRO 12.60.26
Remove the oil pan, see Section 4.27.
1 Place a drain tray under the transfer housing. Remove the
housing bolts and housing
(1,2 Fig. 1).
. Remove the pick-up pipes (3 Fig. l), push back the lock
tabs (1 Fig. 2) and remove the pump sprocket bolts (2 Fig. 2).
. Remove the oil pump drive sprocket (3 Fig. 2), tab washer (4 Fig. 2) and shims.
. Remove the oil pump securing bolts and remove the
pump.
. Removethe pressure relief valve cap, spring, mandrel and
valve
(1-4 Fig. 3).
1 Clean the mating face in the cylinder block, the relief valve
assembly, sprocket and shims.
. Lubricate the relief valve assembly, assemble into new
pump, tighten the cap.
. Fitthe new oil pump tothe engine and tighten thesecuring
bolts.
1 Movethedrivechain asfar rearward aspossible,fit a shim
pack of 0.015 in. thickness to the oil pump flange (3 Fig. 4), align the bolt holes, fit the drive sprocket and two securing
bolts. Using
a straight edge (2 Fig. 41, check the alignment
of the oil pump drive sprocket (1 Fig. 4) and crankshaft
sprocket (4 Fig. 4).
1 Remove and refit the pump drive sprocket and adjust the
value of shim thickness as required in order to align the
sprockets.
. When the alignment is satisfactory, remove the pump
sprocket. Fit the chain and shims to the sprocket,fit to the
oil pump. Fit the tab washer and securing bolts. Tighten
the bolts and lock over the tabs.
. Ensure that the tension of the oil pump drive chain is cor- rect, see Service Data in the Preliminary Pages. Adjust by
slackening the tensioner securing screws, tapping the
tensioner inwards to increase the tension, and securing in
position when the tension is correct.
1 Fit new ‘0 rings to the oil pump pick-up pipes.
. Lubricate and refit the pipes to the pump.
1 Fit and seat the transfer housing. Fit and tighten the secur-
. Refit the oil pan, see Section 4.27.
ing bolts.
Fig. 3
Fig. 4
Issue 1 August 1994 51

AJ16 Engine Service Manual
4.32 Oil Pump, Overhaul
SRO 12.60.32
8 Remove the oil pump, see Section 4.31.
1 Remove the bolts securing the pump body.
1 Remove the pump body, pump outer rotor, backplate se-
1 Clean all component parts of the pump.
1 Check all the clearance and components for undue wear
(Fig.
1) and (Fig. 2). Check tolerances, see Service Data in
the Preliminary Pages.
curing
bolts, the backplate and the bearing shell.
. Fit the bearing shell to the housing.
1 Apply sealantto the backplate gasketface,fitthe backplate
and securing bolts. See Service Materials in the Prelimi- nary Pages.
1 Fit the outer rotor.
a Lubricate the relief valve assembly and assemble into the
1 Tighten the relief valve cap.
1 Refit the oil pump, see Section 4.31.
pump.
Fia. 1
Fin. 2
Issue 1 August 1994 52

D
Drive belt tensions, xvi
F
Fau It diagnosis
Diagnostic procedures, 3
Introduction, 3
Foreword, iii
General description
Construction, 1
Cooling system, 2
Crankcase breather, 1
Cylinder head, 1
Lubrication system, 1
Supercharger, 2
S
Service data, xiii
Service materials, xii
Service operations
Check & adjust
Crankshaft end
-float, 27
Valve clearances, 10
Cylinder head, 16
Engine assy., 33
Oil pump, 52
Auxiliary shaft, 44
Auxiliary shaf? rear seal, 45
Camshaft, 7
Camshaft cover gasket, 9
Connecting rod bearings, 22
Crankshaft, 24
Crankshaft damper /pulley assy., 26
Crankshaft front oil seal, 28
Crankshaft rear oil seal, 29
Cylinder head casting, 19
Cylinder head gasket, 13
Drive-plate, 31
Flywheel, 30
Main bearings, 23
Oil filter head gasket, 46
Oil pan gasket, 47
Oil pick-up strainer, 49
Oil pressure relief valve, 50
Oil pump, 51
Oil pump pipe ‘0’ ring, 48
Pistons &connecting rods, 20
Timing chain damper, 40
Timing chain tensioner
Overhaul
Renew
Lower,
42
Upper, 41
Timing chain, gear & tensioner, 37
Timing sprocket, Intermediate, 43
Transmission adapter plate, 32
Service procedures
Sealants, 2
SPS joint control system, 2
Service tools & equipment iv
T
Torque tightening specifications,
53