1994 JAGUAR XJ transmission

AJ16 Engine Service Manual
CON TENTS
Section SRO Page
Foreword ........................................................................\
.. iii
I ................ Service Tools & Equipment ........................................................... iv
I1 ................ Torque Tightening Specifications ....................................................... vii
111 ............... Service Materials .................................................................... xii
1V ............... Service Data ...................................................................... xiii
1 ................ General Description .................................................................. 1
1.1 .............. Construction ........................................................................\
1
1.2 .............. Cylinder Head Design ................................................................ 7
1.3 .............. Crankcase Breather ................................................................... 7
1.4 .............. Lubrication System ................................................................... 1
1.5 .............. Cooling System ...................................................................... 2
1.6
.............. Supercharger ........................................................................\
2
2 ................ Service Procedures ................................................................... 2
2.1 .............. SPSloint ControlSystem .............................................................. 2
2.2 .............. Sealants ........................................................................\
.... 2
3 ................ Fault Diagnosis ...................................................................... 3
3.1
.............. Introduction ........................................................................\
. 3
3.2
.............. Diagnostic Procedures ................................................................ 3
4
................ Service Operations ................................................................... 7
4.1 .............. Camshaft, Renew .............................................. 12.13.01 ............. 7
4.2 .............. Camshaft Cover Gasket. Renew .................................. 12.29.39 ............. 9
4.3
.............. Valve Clearance, Checkand Adjust ............................... 12.29.48 ............ 10
4.4 .............. Cylinder Head Gasket, Renew ................................... 12.29.01 ............ 13
4.5
.............. Cylinder Head, Overhaul ........................................ 12.29.19 ............ 16
4.6
.............. Cylinder Head Casting, Renew ................................... 12.29.15 ............ 19
4.7
.............. Piston and Connecting Rod, Engine Set, Renew ..................... 12.17.10 ............ 20
4.8
.............. Connecting Rod Bearing, Engine Set, Renew ....................... 12.17.16 ............ 22
4.9
.............. Main Bearing, Engineset, Renew ................................. 12.21.39 ............ 23
4.10 ............. Crankshaft, Renew ............................................. 12.21.33 ............ 24
4.11
............. Crankshaft Damper/Pulley Assembly, Renew ...................... 12.21.09 ............ 26
4.12
............. Crankshaft End-float, Check andAdjust ........................... 12.21.26 ............ 27
4.13
............. Crankshaft Front Oil Seal, Renew ................................. 12.21.14 ............ 28
4.14
............. Crankshaft Rear Oil Seal, Renew ................................. 72.21.20 ............ 29
4.15
............. Engine Flywheel, Renew ........................................ 12.53.07 ............ 30
4.16
............. Engine Drive-plate, Renew ..................................... 12.53.13 ............ 31
4.17 ............. Engine Rear/ Transmission Adapter Plate, Renew ................... 12.53.03 ............ 32
4.18
............. Engine Assembly, Overhaul ...................................... 12.4 7 . 05 ............ 33
4.19
............. liming Chain, Gear and Tensioner, Engine Set, Renew ............... 12.65.13 ............ 37
4.20
............. Timing Chain Damper, Vehicle Set, Renew ......................... 12.65.48 ............ 40
4.21
............. liming Chain Tensioner, Upper, Renew ............................ 12.65.29 ............ 41
4.22
............. Timing Chain Tensioner, Lower, Renew ............................ 12.65.30 ............ 42
4.23
............. Timing Sprocket, Intermediate, Renew ............................ 12.65.26 ............ 43
4.24
............. Auxiliary Shaft, Renew ......................................... 12.10.30 ............ 44
4.25
............. Auxiliary Shaft Rear Seal. Renew ................................. 12.10.32 ............ 45
0
i Issue 1 August 1994

AJ16 Engine Service Manual
Cylinder Block
Adapter to cylinder block
Bearing cap to cylinder block
Blanking plate to cylinder block
Manual transmission to engine
(4,O liter supercharged automatic)
Oil drilling blanking plug
Oil gallery blanking setscrew
Oil pressure sensor
Oil pressure sensor plug
Oil seal adapter to cylinder block
Transmission adapter to cylinder block
Water drain plug
Windage tray to cylinder block
Cylinder Head and Camshaft Cover
Bearing cap to cylinder head
Camshaft coupling bolt
(Nm)
43 - 57
136
- 142 (SPS
System)
21,5 - 28,5
43 - 57
29
- 39
21,5 - 28,5
23 - 27
8,5- 11,5
21,5 - 28,5
44.5 - 59,5
64.5 - 79.5
21.5
- 28,5
17 - 23
22
- 28
Camshaft cover to cylinder head
- - . ~. Cylinder head to cylinder block
Cylinder head to timing cover -
______ ____ Exhaust manifold to cylinder head
On
-plug coil cover to camshaft cover
Rear cover to cylinder head
4-5
59 - 61 (SPS System) ~~ -. . - 21,5 - 28,5
22 - 28
_. . -.. ___ Dipstick
Tube
Dipstick tube assembly nut
Dipstick tube attachment to tube support bracket
(4,O liter supercharged)
__ Dipstick tube bracket (4,O liter supercharged)
Dipstick tube to bracket
Drive Chain System
Dipstick tube bracket screw
Auxiliary shaft assembly setscrew
Coupling to intermediate shaft
Damper to cylinder block (bolt)
Damper to cylinder block (screw)
Damper to distance piece
Damper to saddle
Distance piece to cylinder block
Endplate to damper
Housing to cylinder block (bolt)
Housing to cylinder block
(capscrew)
Pivot bracket to cylinder block
Pivot plate to cylinder block
Sprocket to hub setscrew
Engine Mounting
Engine mounting bracket to engine
Issue 1 August 1994 viii
81 -99
15.5 - 20,5
5-7
9,5
- 12,5
5%: 7.8
30,5 - 37,5
12-16
21,5 - 28,5
21.5 - 28,5
21,5 - 28,5
21,5 - 28,5
21,5 - 28,5
21.5 - 28,5
21,5 - 28,5
21,5 - 28,5
21,5 - 28,5
2 1,5 - 28,5
9,5 - 12,5
445 - 59,5

AJ16 Engine Service Manual
Exhaust Manifold
Exhaust manifold to cylinder head
Heatshield to exhaust manifold
Lifting eye setscrew (slave item only)
.~ Fuel System
Fuel pressure regulator to bracket
Fuel rail connecting nut
. i------
44,5 - 59.5
21.5
- 28,5
21.5 - 28,5
~- 30.5 - 41,5
12,5 - 15,5
Fixing
- Adjuster bracket to oil pan
Adjuster sleeve
to generator
Generator mounting bracket pivot bolt
Sleeve to adjuster bolt
21,5 - 28,5
17 - 23
34
- 46
11 - 15
__~___.___ 21.5 - 28,5 __ ~~ ~ Generator
Mounting
bdjuskr bolt to timing cover
Intake Manifold
Blanking plate to intake manifold (in place of adapter) 9,5 - 12,5
8,5- 11,5
9,5 - 12,5
36 - 44
14.5
- 19.5
LBreather adapter to intake manifold (4,O liter normally aspirated)
l EGR adapter to intake manifold
EGR pipe to adapter
EGR sensor to intake manifold 1
1 Intake manifold steady screw (4,O liter supercharged)
Intake manifold
to cylinder head
Pedestal to throttle body
22 - 28
21,5 - 28,5
9,5 - 12,5
Pressure regulator to intake manifold
Pressure regulator to intake manifold
(4.0 liter supercharged)
9,5 - 12,5
5-7
Throttle linkage baseplate to pedestal
assembly nut
Purge adapter
to intake manifold
Throttle body to intake manifold
9,5 - 12,5
21,5 - 28,5
9,5 - 12.5
1.8 - 2,2
'Throttle cable abutment to intake manifold
Throttle linkage actuator nut
9,5 - 12,5
Throttle stop screw locknut
Miscellaneous Hoses
Hose clamp, breather hose to restrictor
Hose clamp, heater return hose to throttle body
4,3 - 5,7
1.5
- 2,5
1,5
- 2.5
Hose clamp, hose to cam cover 2,5 - 3.5
' Hose clamp, restrictor to throttle body
I Oil cooler clamp screw 5-7
1.5
- 2,5
Oil
cooler pipe bracket screw 1.5 - 2.5
l Hose clamp, thermostat housing to restrictor ~
Hose
clamp, water pump
Oil Cooler (4.0 Liter Supercharged)
Hose clamp, oil cooler hose to radiator cradle
..
Oil cooler pipes to engine 14-18
1,5
- 2,5
2,5
- 3.5
7
-10
Oil cooler to body
Tube nut, all except those shown below 17 - 23
17
- 23
16 - 20 ,Tube nut, transmission pipes to transmission
Issue 1 August 1994 ix

AJ16 Engine Service Manual
0 Fixing
Oil Pump, Filter and Oil Pan
Baffle tray to oil pan
Drain plug to oil pan
Pick
-up to carrier
Filter head to cylinder block
Front cover to body
Oil filter canister
Oil pan to cylinder block
Oil pan to timing cover
Oil pump and oil pump carrier to cylinder block
Rear cover to body
Relief valve plug Tightening
Torque
(Nm)
21,5 - 28,5
64.8 - 79,2
9,5 - 12,5
21.5 - 28.5
9,5
- 12,5
12-15
21,5 - 28,5
21,5 - 28,5
21,5 - 28.5
9.5
- 12,5
35,7 - 48,3
Power Steering
Adapter to housing 21,5 - 28,5
Power steering pump to adapter
Power steering pump to engine
spark Plug
Starter Motor
Starter motor to adapter
Transmission to starter motor
Supercharger-
Spark plug
--
44.5 - 59,5
22 - 28
22
- 28
43
- 57
43
- 57 -___
Adapter to timing cover
Air duct clamp to intercooler
Air duct hoses
Air duct lower to intercooler 22 - 28
2,5
- 3,5
2,5
- 3,5
2,5 - 3,5
Air duct upper casting to lower
Bypass valve to throttle body
Elbow to intercooler
Idler bracket
/ timing cover to cylinder block
Idler bracket to water pump
X Issue 1 August 1994
2,5 - 3,5
8,5
- 11,5
22 - 28
22
- 28
22
- 28
Idler mounting bracket
Intercooler water pipes
Outlet elbow to supercharger
Pulley to carrier
Supercharger mounting bracket to engine
Supercharger mounting stud 22 - 28
22
- 28
22
- 28
22
- 28
43
- 57
22
- 28
Supercharger to mounting bracket 43 - 57
Tensioner bracket / timing cover to cylinder block 22 - 28
Tensioner bracket to adapter
Throttle body adapter to bypass actuator 22 - 28
8,5
- 11.5

AJ16 Engine Service Manual
Description
Hylosil 102 sealant
111. SERVICE MATERIALS
UseS Notes
Oil pick-up strainer to transfer housing
Thermostat housing to extension
I jThermostat outer housing to inner housing
Loctite
501 sealant
~. Xming cover to cylinder block
t Transmission adapter to cylinder block
drive
-plate bolt
Oil pump front cover to body
[Oil pump rear cover to body
1 Oil filter threaded insert to housing
Loctite 542 sealant
__ __ Loctite 573 sealant to
cylinder block
Issue 1 August 1994 xii

AJ16 Engine Service Manual
SERVICE DATA
Engine Data
Application Item
Number of cylinders
Bore
Specification
Seneral 6
91
mm
Stroke 3,2 liter: 83 mm
4,O liter: 102 mm
3.2 liter: 3239 cm3
4.0 liter: 3980 cm3
Cubic capacity
Compression ratio
3.2 liter: 1O:l
4,O liter: 1O:l (normally aspirated)
4,O liter: 8,51 (supercharged)
1,5,3,6,2,4 (No. 1 cylinder at
crankshaft pulley end)
Fully mapped Lucas engine
management system with digital
ignition
Firing
order
gnition timing
0
0
0
Jalve clearance
Intake and exhaust 0,30 to 0,36 mm
Champion RCSYCC (except North
America, normally aspirated
engines)
Champion
RC12YCC (North
America, for normally aspirated
engines only)
__ ~ ~
--__ ~~
Spark
plug
0,9 mm
On-plug ignition coil
Diamond
Number per vehicle
Primary winding resistance
Current consumption ~ ~~
6
0,75 ohm
Oto6A
Clockwise
(viewed from above)
1,5,3,6,2,4 (No. 1 cylinder at
crankshaft pulley end)
-
Engine position sensor
Fuel injection equipment
Exhaust Emission Rotation
Firing order
Micro
-processor controlled engine
management system
Fuel pressure
Exhaust gas analyzer reading (at
engine idle speed, normal operating
temperature and with catalytic
converter fitted)
3 bar
0,5% CO maximum.
For Swiss market only:
0,02% CO
maximum,
70 ppm HC maximum
Idle speed (engine at normal
operating temperature) Manual transmission 700 RPM
Automatic
transmission 700 RPM (gear selector in neutral)
11,O to 11,7 bar (with all spark plugs
removed, throttle fully open, engine
at operating temperature and
a
minimum cranking speed of 300
RPM)
0,7 bar (maximum)
Compression pressure
Cylinder pressure
Differential pressure between
cylinders
Aluminum alloy
Cylinder block
. ___ Material
xiii
Issue 1 August 1994

AJ16 Engine Service Manual
4.7 Piston
and Connecting Rod, Engine Set, Renew
SRO 12.17.10
. Remove the engine and transmission unit from the ve- hicle, see Section 3.1 in the appropriate Vehicle Service
Manual.
1 Remove the transmission unit from the engine and fit the
engine to a stand.
. Remove the cylinder head, see Section 4.4.
* Remove the oil pan, see Section 4.27.
1 Remove the oil pump, see Section 4.31.
. Remove the windage trays securing bolts. Remove the
windage trays (6 Fig. 1).
* Remove the connecting rod nuts (1 Fig. 2) in connecting
rod pairs(1 &6,2 &5,3&4cylinders)andremovethecon- necting rod bearing caps (2 Fig. 2). Note the position of
the cap to connecting rod. Discard
the connecting rod
bearing nuts.
Push the pistons up and through the top of the cylinder
block.
. Remove the piston pin snap-rings (1 Fig. 3)from each pis- ton, remove the piston pin (2 Fig. 3) and separate the pis-
ton (3 Fig. 3) from the connecting rod (4 Fig. 3).
. Check the connecting rods for out of balance, twist and
bend. If any connecting rod is bent, twisted or out of bal- ance with the other five, then the complete set must be re- newed. Renew
the connecting rod bearing bolts.
.a
Fia. 1
,11613
Fig. 2
I 4 Ii I
Fig. 3
-3
ill 631
Issue 1 August 1994 20

AJ16 Engine Service Manual
Insert each new piston ring into the cylinder bore (1 Fig. 1)
ensuring they are square in the cylinders and check the
gap using a strip gauge
(2 Fig.1).
9 If the gap is insufficient, then a small flat file or carborun- dum stone can be used on the butting ends of the ring. En- sure that after filing no burrs remain.
Ensure that the rings are not inter
-mixed after they
have been gapped and that each piston/ring assem-
bly is matched to its respective bore. If new piston
rings are being fitted without reboring, deglaze the
cylinder bores using a hone or glaze
buster. This
operation will not increase the size of the bores and
will give the bores a cross
-hatched finish
. Lubricate the small end bush and slide the piston pin
through the new piston and connecting rod. Secure with
new snap
-rings. NEVER re-use old snap-rings.
Fit the rings to the pistons ensuring that gaps are posi- tioned as in (Fig. 2).
Lubricate and compress the rings using Service Tool 18G 55A (Fig. 3).
w:
b: Ensure that each piston / ring assembly is matched
to its respective bore.
. Insert the piston skirt intothe bore and using a suitable im- 0
plement, i.e. a wooden hammer shaft, gently tap the pis- ton into the cylinder bore.
. Ensurethattheconnecting roddoes not foul eitherthecyl- inder block or crankshaft.
Note: Ensurethateachconnecting rod andconnecting rod
m Lubricate and fit the connecting rod bearing shells to the
connecting rod and the connecting rod bearing cap. Pull
the connecting rod and bearing carefully onto the crank
- shaft and fit the connecting rod bearing cap to the rod.
Fit and torque tighten the new connecting rod bearing
nuts.
CAUTION: The connecting rod bearing nuts and bolts MUST be renewed during assembly and torque
tightened asdescribed inSection2.1, SPS Joint
Control System.
. Repeat the operation for the remaining five piston assem-
bearing cap are correctly 'paired' for assembly.
blies.
Clean and fit the crankshaft
windage trays and torque
-
0 - - tighten the securing bolts.
Refit the oil pump, see Section 4.31.
. Refit the oil pan, see Section 4.27.
Refit the cylinder head, see Section 4.4.
Remove the engine from the stand.
Attach the transmission unit to the engine.
. Fit the engine / transmission unit to the vehicle, see Sec- tion 3.1 in the appropriate Vehicle Service Manual.
Fin. 1
itl6.l
Fig. 2
Fig. 3
Issue 1 August 1994 21