1994 CHEVROLET TRACKER tire size

:enter High-Mounted Stoplight
Hardtop)
i, remove the bulb:
. Remove the side pins.
!. Pull the housing forward.
1. Turn the socket counterclockwise and
pull
it out.
I. Pull the bulb out of the socket.
i. Reverse the steps with a new bulb.
ll TIRE PLACARD
GVWR ~GAWR FRT GAWR RR
I TIRES I
I PRESSURE COLD PSl!kPa I
IJ
Center High-Mounted Stoplight
(Convertible)
To remove the bulb:
1, Remove the two screws and the lens
housing.
pull
it out.
2. Turn the socket counterclockwise and
3. Pull the bulb out of the socket.
4. Reverse the steps with a new bulb.
Loading Your Vehicle
Two labels on your vehicle show how
much weight
it may properly carry. The
Tire-Loading Information label found
on
the driver’s door lock pillar tells you the
proper size, speed rating and
recommended inflation pressures for the
tires on your vehicle.
It also gives you
important information about the number
of people that can be
in your vehicle and
the total weight that
you can carry. This
weight is called the Vehicle Capacity
Weight and includes the weight
of all
occupants, cargo, and all
nonfactory-installed options.
181 . . .
ProCarManuals.com

-
Service and Appearance Care
When It’s Time for New Tires
One way to tell when it’s time for new
tires
is to check the treadwear indicators,
which will appear
when your tires have
only
2/32 inch (1.6 mm) or less of tread
remaining.
You need a new tire
if
0 You can see the indicators at three or
more places around
the tire.
0 You can see cord or fabric showing
through the tire’s rubber.
The tread or sidewall is cracked, cut
or snagged deep enough to show cord
or fabric.
The tire has a bump, bulge or split.
. . ,186
0 The tire has a puncture, cut, or other
damage that can’t be repaired well
because of the size or location
of the
damage.
Buying New Tires
To find out what kind and size of tires you
need,
look at the Certificationnire label.
The tires installed on your vehicle when it
was new had a Tire Performance Criteria
Specification (TPC Spec) number on each
tire’s sidewall. When you get new tires,
get ones with that same TPC Spec
number. That way, your vehicle
will
continue to have tires that are designed to
give proper endurance, handling, speed
rating, traction, ride and other things
during normal service on your vehicle. If
your tires have an all-season tread design,
the TPC number will be followed by a
“MS” (for mud and snow).
If you ever replace your tires with those
not having a TPC Spec number, make
sure they are the same size, load range,
speed rating and construction type (bias,
bias-belted or radial) as your original
tires.
Uniform Tire Quality Grading
The following information relates to the
system developed by the United States
National Highway Traffic Safety
Administration which grades tires by
treadwear, traction and temperature
performance. (This applies only to
vehicles sold
in the United States.)
Treadwear
The treadwear grade is a comparative
rating based on the wear rate
of the tire
when tested under controlled conditions
on a specified government test course. For
example, a tire graded
150 would wear
one and a half
(1 1/2) times as well on the
government course as a tire graded 100.
The relative performance of tires depends
ProCarManuals.com

Service and Appearance Care
If you need to replace any of your wheels,
wheel bolts, or wheel nuts, replace them
only
with new GM original equipment
parts. This way, you
will be sure to have
the right wheel, wheel bolts, and wheel
nuts for your Geo model.
NOTICE:
The wrong wheel can also cause
problems
with bearing life, brake
cooling, speedometer/odometer
calibration, headlight aim, bumper
height, vehicle ground clearance,
and
tire or tire chain clearance to the
body and chassis.
Used Replacement Wheels
A CAUTION:
Putting a used wheel on your vehicle
is dangerous. You can’t know how
it’s been used or how many miles it’s
been driven. It could
fail suddenly
and cause an accident.
If you have
to replace a wheel
use a new GM
original equipment wheel.
Tire Chains
NOTICE:
Use tire chains only where legal and
only when you must. Use only SAE
Class “S” type chains that are the
proper size for your tires. Install them
on the tires of the drive axle (four-
wheel drive vehicles can use chains
on both axles). Tighten them
as
tightly as possible with the ends
securely fastened. Drive slowly and
follow the chain manufacturer’s
instructions.
If you can hear the
chains contacting your vehicle, stop
and retighten them.
If the contact
continues, slow down until
it stops.
Driving too fast with chains
on will
damage your vehicle.
. . .188 ProCarManuals.com