1994 CHEVROLET ASTRO PASSENGER radio

Downloaded from www.Manualslib.com manuals search engine PWR (Power)
The PWR button turns your system on and off,
AM-ST Button
Push this button if you want AM stereo. (“STEREO” will be displayed
when you are receiving an
AM stereo station.)
Cr02 Button
The Cr02 button lets you set the system for the type of cassette being used.
If you are using chrome or metal tapes, push the
Cr02 button in. If you are
using standard iron tapes, make sure the button is out.
Your audio system has automatic Dynamic Noise Reduction. It helps
remove background hiss noise from the radio or tape player.
DNR@
DNR@ is a registered trademark of the National Semiconductor
Corporation.
Pushbuttons
The four pushbuttons let you return to favorite stations.
You can set the pushbuttons for up to eight favorite stations
(4 AM and
4 FM). Just:
Tune in the station.
0 Push SET. (SET appears in the VF display for a few seconds.)
0 Within 5 seconds, push one of the four pushbuttons. Whenever you
push that button, the preset station will return.
Repeat these steps for each pushbutton.
NOTE:
You can preset 3 more stations on each band by pushing a pair of buttons
next to each other at the same time. Just:
Tune in the station.
0 Push SET. (SET appears in the VF display for a few seconds.)
0 Within 5 seconds, push two buttons next to each other at the same time.
Whenever you push that pair of buttons, the preset station will return.
Repeat these steps for each pair of buttons.
SCAN Button
When you push this, the radio will go to the next station and stay there a
few seconds. Then it will go to the next station and pause, and keep doing
that. Press
SCAN again to stop scanning.
SEEK Button
This chooses stations also, but it doesn’t keep moving as SCAN does. When
you push SEEK, the radio goes to the next station and stays there.
3-17

Downloaded from www.Manualslib.com manuals search engine Clock
To set the clock, just:
0 Press SET. (SET appears in the VF display for a few seconds.)
Within 5 seconds, push and hold SCAN until the correct hour appears.
0 Press and hold SEEK until the correct minute appears.
To display
the clock with the ignition off, push the upper knob. The time
will be displayed for a few seconds.
To Play A Cassette
Your tape player is built to work best with tapes that are 30 to 45 minutes
long on each side. Tapes longer than that are
so thin they may not work well
in this player.
To play a cassette tape:
Have the radio on.
0 Insert the tape squarely through the tape door.
The longer side with the tape visible goes in first. If you hear nothing or
hear just garbled sound, it may not be
in squarely.
Push
STOP-EJECT to remove the tape and start over.
Once the tape is playing, use the upper and lower knobs for volume and
balance, just as you do for radio. The arrows show which side of the tape is
playing.
0 To go forward to another part of the tape, push ,.
To go backward, push 4. To stop the tape, push the STOP-E JECT
button lightly.
0 To go from one side of the tape to the other, push in the upper knob on
your radio. To remove or stop the tape, push
STOP-EJECT.
APS (Automatic Program Search)
Press this button to activate the automatic program search. When the
button is pressed, the tape will rapidly advance to the beginning
of the next
selection. When the
4 button is pressed, the tape will rapidly reverse to the
beginning
of the current selection.
Press
STOP-EJECT to remove the cassette and start the radio.
3-18

Downloaded from www.Manualslib.com manuals search engine How to Operate Your ETP AM-FM Stereo
Audio Compact Disc (CD) System
This part tells you how your ETR' AM-FM stereo system works:
Upper Knob (PWR-VOL)
The upper knob
has three functions:
It switches the radio on and off when the ignition is on.
It controls the volume. Volume will increase when the RCL knob is
turned to
the right and decrease when turned to the left. Volume will be
displayed briefly unless LefdRight speaker control, Rearmront speaker
control,
BASS or TREB are adjusted.
It controls the mute feature. By pressing the MUTE knob, all sound
from the radio or
CD player stops. By pressing the knob again, or by
turning the
VOL knob to the right, sound will begin again.
Lefmight Speaker Control
The control ring behind the upper knob allows
you to balance the sound
between the left and right speakers. Balance will
be displayed briefly when
using this control.
Lower Knob
The lower knob
I_.._ . YO functions:
It enables you to tune in different radio stations by turning the knob to
It enables you to alternate between AM and FM stations by pressing the
the right
or to the left.
BAND knob. Your selection will be briefly displayed.
Rearmront Speaker Control
The control ring behind the lower knob fades the sound between you\
r rear
and front speakers. Fade levels will be briefly displayed.
3-20

Downloaded from www.Manualslib.com manuals search engine SEEK
Pressing the SEEK button will cause the receiver to seek the next higher
station and stop.
Pressing the
4 SEEK button will cause the receiver to seek the next lower
station and stop.
SCAN
When you press SCAN, the radio will go to the next station and pause, and
will keep scanning until you press
SCAN again. SC will be displayed when
using this control.
Pushbuttons
The five pushbuttons let you return to favorite stations. They are also used
when you play a disc. (See “To Play
A Compact Disc”.)
To set
the pushbuttons for up to ten favorite stations (5 AM and 5 FM):
Tune in the desired station.
Push the SET button. (SET is displayed briefly.)
Within 5 seconds, push one of the five pushbuttons to store the station.
Whenever
you press that button, the preset station will return.
Clock
To set the clock, just:
Press the SET button. The radio may be on or off.
Within 5 seconds, press and hold either SEEK to increase the
minutes or
4 SEEK to decrease the minutes until the correct minute
appears on the display.
Press and hold SCAN until the correct hour appears on the display.
RCL
Press the RCL button to alternate between time and radio station on the
display.
RCL may be pressed when the ignition is off to see the time.
BASS
Press the BASS A to increase the bass tones and BASS to decrease bass
tones. Press
the center of the control for a preset BASS position. The bass
level will be displayed briefly when using this control.
TREBLE
Press the TREB A to increase the treble tones and TREB to decrease
the treble tones. Press the center of the control for a preset
TREB position.
The treble level will be displayed briefly
when using this control.
3-21

Downloaded from www.Manualslib.com manuals search engine SCAN
Press SCAN to sample each track for approximately 10 seconds. Scanning
will continue until the
RDM, SCAN or any other motion button is pressed
again.
PREV
If you hold the PREV (4 SEEK ) button, or press it more than once, the
disc will return to previous tracks.
NEXT
Press NEXT (SEEK b ) to hear the next track now instead of waiting until
the present track
is finished. If you hold this button or press it more than
once, the disc will advance further.
ST-PL
Press ST-PL (Stop-Play) to make the disc stop and the radio play. Press
ST-PL again to restart the disc at the point where it stopped.
Press
PWR or turn the ignition key off to stop the disc player. The disc
stays in the player and will resume playing at the point where
it stopped.
Press
EJCT to eject the disc and make the radio play. The disc will start at
track
1 when you reinsert it.
Anti-Theft Feature
Delco LOC II@ is an Anti-Theft feature for the compact disc player. It can
be used or ignored.
If ignored, the system plays normally. If it is used, your
player won’t be usable if
it is ever stolen, because it won’t turn on.
The instructions below tell you how
to enter a secret code into the system. If
your car loses battery power for any reason, you must unlock the system
with the secret code before
the radio will turn on.
To Lock The System:
1. Write down any 6 digit number and keep it in a safe place.
2. Turn the ignition to the ACC (Accessory) or RUN position.
3. Press the PWR button to turn the radio off.
4. Press the 1 and 4 buttons together. Hold them down until “- - -” shows
on the display.
You are now ready to enter your secret code. Don’t wait more than
15 seconds between steps.
5. Press SET and 000 will appear on the display.
6. Press the SEEK b or 4 button to make the first number appear.
7. Press SCAN to make the last two numbers agree with your code.
3-23

Downloaded from www.Manualslib.com manuals search engine 8. Press BAND and 000 will appear again. Now you are ready to enter the
last three digits of your code.
9. Repeat steps 6 and 7 for the last three digits of your code.
10. Press
BAND and rEP will appear for 5 seconds and then 000 will
11. Repeat steps
6 through 10. This time SEC will appear-indicating that
appear.
the radio
is secure.
To Unlock The System After A Power Loss
When battery power is reapplied to a secured radio, the radio won’t turn on
and
LOC will appear on the display.
Enter your secret code as follows: pause no more than
15 seconds between
steps.
1. Turn the ignition on. (Radio off.)
2. Depress the SET button. The display will show 000.
3. Enter the six digits of the code following steps 6-9 above. The display
4. Depress the BAND knob and the time appears - indicating that the
disabling sequence was successful. If the display indicates
SEC, the
numbers did not match and the unit is still secured.
will show the numbers as entered.
Disabling The Theft System
1.
2.
3.
4.
5.
6.
Depress presets 1 and 4 for 5 seconds with ignition on and radio power
off. The display will show
SEC, indicating the unit is in the secure
mode.
Depress the
SET button. The display will show 000.
Enter the first three digits of the code following steps 6 and 7 of the
preceding paragraphs. The display
will show the numbers as entered.
Depress
the BAND knob. The radio will display 000.
Enter the second three digits of the code. The display will show the
numbers as entered.
Depress the
BAND knob. If the display shows bb- - - ”, the disabling
sequence was successful. The numbers matched the user-selected code
or the factory back-up code, and the unit
is in the UNSECURED mode.
If the display shows
SEC, the disabling sequence was unsuccessful and
the numbers did not match either of the codes and the unit will remain
in the SECURED mode.
3-24

Downloaded from www.Manualslib.com manuals search engine 2. Get the vehicles close enough so the jumper cables can reach, but be
sure the vehicles aren’t touching each other. If they are, it could cause a
ground connection you don’t want. You wouldn’t be able to start your
vehicle, and the bad grounding could damage the electrical systems.
You could be injured if the vehicles roll. Set the parking brake firmly
on each vehicle. Put an automatic transmission
in “P” (Park) or a
manual transmission in
“N’ (Neutral). If you have a four-wheel-drive
vehicle with a manual transfer case shift lever, be sure the transfer case
is not in
“N’ (Neutral).
needed, and radios. This will avoid sparks and help save both batteries.
And it could save your radio!
3. Turn off the ignition on both vehicles. Turn off all lights that aren’t
NOTICE:
If you leave your radio on, it could be badly damaged. The
repairs wouldn’t be covered by your warranty.
4. Open the hoods and locate the batteries. Find the positive (+) and
negative
(-) terminals on each battery.
5-4

Downloaded from www.Manualslib.com manuals search engine ruse Block
The fuse block is
under the instrument
panel
on the driver’s
side. Remove the
cover with
a
screwdriver.
To remove fuses if you don’t have a fuse extractor, hold the end of the fuse
between your thumb and index finger and pull straight out.
Be sure to use the correct fuse.
If you ever have a problem on the road and
don’t have a spare fuse, you can “borrow” one
of the correct value. Just pick
some feature of your vehicle that you can get along without-like the radio
or cigarette lighter-and use its fuse, if it is of the value you need. Replace
it as
soon as you can. See “Fuses and Circuit Breakers” in this section.
6-67