1993 GMC SIERRA light

Comfort Controls & Audio Systems
AM Stereo
This means the Delco@ system can receive C-QUAM@ stereo broadca\
sts. Many AM stations around the country use C-QUAM@
to produce stereo,
though some do not. (C-QUAM@ is a registered trademark of Motorola, Inc.).
If your Delco@ system can get C-QUAM? your “STEREO” light will come on
when you’re receiving it.
How to Operate Your AM ETWRadio
I 2 3 4 ..
K2186
To Play the Radio
Press the PWR-VOL-TONE knob to switch the radio on and off. This knob
does
two other things:
It controls the volume. The VOL knob increases the volume when
rotated clockwise.
The knob behind the PWR-VOL knob is the TONE knob. Rotate this
knob counterclockwise for more bass and clockwise for more treb\
le.
TUNE Button
Press the side of the button with the down arrow to decrease the radio
frequency or the side of the switch with the up arrow to increase the radio
frequency.
RCL Button
When the ignition is off, press the RCL button to display the time. With the
ignition in
RUN or ACC, press it to recall the station frequency when the time
is showing.
3-1 0
ProCarManuals.com

Comfort Contmls & Audio Systems
and bottom buttons adjusts the front and rear speaker volume, \
or fade. The relative balance and fade adjustments are shown on the VF display.
TUNE
Press the (t) to increase frequency and (-) to decrease frequency.
AM/FM
Push to get AM or FM.
SEEK
Press the SEEK button to make the receiver seek, and stop at, the next
higher available station.
SCAN
Press the SCAN button to make the receiver scan, and momentarily pause at
all available stations.
SCAN will appear in the VF display while the receiver is
in the scan mode. Press
SCAN again to cancel the scan mode and hold the
current station.
Pushbuttons
The six pushbuttons let you return to favorite stations. You can set the
pushbuttons for up to twelve favorite stations
(6 AM and 6 FM). To set the
pushbuttons, just:
Tune in the station you want.
Press the SET button. (SET appears in the VF display for a few
seconds.)
0 Within 5 seconds, push one of the six pushbuttons to store the station.
After that, whenever you press that button, the preset station \
will return.
Ciock
To set the clock, just:
Press the SET button. The word SET will light up in the VF display.
Within 5 seconds, press and hold the SEEK button until the correct hour
Then, press and hold the SCAN button until the correct minute appears
After you set the time, the word SET will remain in the VF display for a
appears on the display.
on
the display.
few seconds.
TREBLE
Push (t) to hear more treble.
Push
(-) to hear less treble.
3-1 2
ProCarManuals.com

BASS
Push (t) to hear more bass.
Push
(-) to hear less bass.
Adjust these buttons to give a pleasing sound.
If a station is weak and noisy,
just reduce
TREB to lessen interference.
Cassette Deck
...................... ..............
...... ._L-.~ ...... ......................
.,~, .. - ........ j__-. .......... ............. ... : .... .................. ..............-I. IX_r"
1
K2310
If you have a cassette deck, it is built to work best with tapes that are 30 to
45 minutes long on each side. Tapes longer than that are so thin that they
may not work well in this player.
Once the tape is playing, use the radio control knobs for vol\
ume, balance
and fade, just as you do for the radio. The arrows on the p\
layer indicate
which side of the tape
is being played.
REV
To rapidly reverse the tape, press REV. The tape will rapidly reverse until you
press the FWD button lightly.
FWD
To rapidly advance the tape, press FWD. The tape will rapidly advance until
you press the
REV button lightly.
PROG
To go from one side of the tape to the other, press the PROG button.
Observe the lighted arrows to determine which side of the tape is being
played.
3-1 3
ProCarManuals.com

TUNE
To tune in radio stations, push the (t) to increase frequency and (-) to
decrease frequency.
A MIFM
Push to get AM or FM.
SEEK
Press the SEEK button to make the receiver seek, and stop at, the next
higher available station.
SCAN
Press the SCAN button to make the receiver scan, and momentarily pause
at, all available stations.
SCAN will appear in the VF display while the
receiver is in the scan mode. Press
SCAN again to cancel the scan mode
and hold the current station.
Pushbuttons
The six pushbuttons let you return to favorite stations. You can set the
pushbuttons for up to twelve favorite stations
(6 AM and 6 FM). To set the
pushbuttons, just:
Tune in the station you want.
Press the SET button. (SET appears in the VF display for a few
seconds.)
Within 5 seconds, push one of the six pushbuttons to store the station.
After that, whenever you press that button, the preset station will return.
Clock
To set the clock, just:
Press the SET button. The word SET will light up in the VF display.
Within 5 seconds, press and hold the SEEK button until the correct hour
Then, press and hold the SCAN button until the correct minute appears
appears on the display.
on the display.
After you set the time, the word SET will remain
in the VF display for a
few seconds.
Tone
To adjust the tone of this radio combination, see the instructions for the
graphic equalizer tape deck.
3-1 5
ProCarManuals.com

Comfort Controls & Audio Systems
AmSt
The AmSt button is just below the PWR button. Push this when you tune to
an AM station that broadcasts in stereo. Your
STEREO light will come on
when you’re receiving AM stereo.
If you push AmSt and there is no more
noise,
it means the station is weak. You’ll hear the station better if you don’t
use
AmSt. Just push the AmSt button again to cancel stereo.
NOTE: Your Delco system may be able to receive C-QUAM@ stereo
broadcasts. Many AM stations around the country use C-QUAM@ to produce
stereo, though some do not. C-QUAM@ is a registered trademark
of Motorola
Inc. If your Delco system can get C-QUAM@ signals, your
STEREO light will
come on when you are receiving stereo.
Cassette Deck with Graphic Equalizer
K2311
Press the PWR button on the radio to turn the unit on. The radio will play
until a cassette is pushed into the cassette entry door (the \
tape side goes in
first.) The cassette deck is built to work best with tapes that are
30 to 45
minutes long on each side. Tapes longer than that are so thin that they may
not work well in this player.
Once the tape is playing, use the
VOL, BAL and FADE controls on the
radio. The arrows indicate which side
of the tape is being played.
Equalizer
Boost the bass, emphasize a voice in a song, brighten the treble-your
equalizer enables you to adjust five separate sound frequencies \
to your
individual taste.
3-1 6
ProCarManuals.com

Press (+) to emphasize a frequency, press (-) to de-emphasize it. It’s best
to begin with all the controls in the middle position, then adjust each control
as you like. Observe the
VF display for relative emphasis.
Cr02
This button sets tape bias. When playing high bias chrome or metal tapes,
press
Cr02 (the light in the button will come on). When playing standard
tapes, press the button again (the light will go out).
PROG
To go from one side of the tape to the other, press the PROG button.
Observe the lighted arrows to determine which side of the tape is being
played.
If a tape is inserted with side “1” (or ‘X,) up, men the up arrow means that
that side is being played. Likewise, a down arrow would indicate that side
“2”
(or “B”) had been selected. The player will automatically switch to the other
side of the tape when the first side ends.
EJECT
Press EJECT to eject the cassette tape from the player (the radio will t\
hen
FWD
To rapidly advance the tape, press FWD. The light in the button will be lit
and the tape will rapidly advance until you press the
REV button lightly.
play.)
SEEK
To
search for the next selection on the tape, forward or back, press SEEK
(the light in the SEEK button will be lit) and either FWD or REV. For the
seek mode to stop, there must be at least a 4-second gap between
selections on the tape.
REV
To rapidly reverse the tape, press REV. The light in the button will be lit and
the tape will rapidly reverse until you press the
FWD button lightly.
REPT
Press REPT to repeat the currently playing selection on the tape. For the
repeat to stop, there must be at least
a 4-second gap between selections.
3-1 7
ProCarManuals.com

Comfort Contrors & Audio Systems
Care of Your Cassette Tape PIayer
A tape player that is not cleaned regularly can cause reduced so\
und quality,
ruined cassettes, or a damaged mechanism. Cassette tapes should be stored
in their cases away from contaminants, direct sunlight, and extreme\
heat.
If
they aren't, they may not operate properly or cause failure of\
the tape player.
Your tape player should be cleaned regularly each month
or after 15 hours of
use. If you notice a reduction in sound quality, try a known good cassette to
see
if the tape or the player is at fault. If this other cassette has no
improvement in sound quality, clean the tape player.
Clean your tape player with a wiping-action, non abrasive clean\
ing cassette,
and follow the directions provided with
it.
Cassettes are subject to wear and the sound quality may degrad\
e over time.
Always make sure that the cassette tape is in good condition \
before you
have your tape player serviced.
K1313
Fixed Mast Antenna
The fixed mast antenna can withstand most car washes without being
damaged.
If the mast should ever become slightly bent, you can straighten it
out by hand. If the mast is badly bent, as it might be by vandals, you should
replace
it.
Check every once in a while to be sure the mast is still tightened to the
fender.
3-1 8
ProCarManuals.com

Your Driving and the Road
Traffic Lights
AM402014
We’re all familiar with traffic lights or stop lights. Often, green arrow\
s are
being used in the lights for improved traffic control. On some multilane road\
s,
green arrows light up, indicating that traffic in one
or more lanes can move or
make a turn. Green arrows don’t mean “go no matter what.\
” You’ll still need
to proceed with caution, yielding the right
of way to pedestrians and
sometimes to other vehicles.
Some traffic lights also use red arrows to signify that you must stop before
turning on red.
I
/
‘I
I
r
REVERSIBLE
LANE ON
ROADWAY MULTI-LANE

- AM40201 5
Many city roads and expressways, and even bridges, use reversib\
le-lane
traffic control during rush
hours. A red X light above a lane means no driving
in that lane at that time.
A green arrow means you may drive in that lane.
Look for the signs posted to warn drivers what hours and days these
systems are in effect.
4-8
ProCarManuals.com