1993 GMC SIERRA clock

Raising your vehicle with the jack improperly positioned will damage the
vehicle
or may allow the vehicle to fall off the jack. Be sure to fit the jack
lift head into the proper location before raising your vehicle.
Front Rear
. .. -,li ... :?
PO288
Raise the vehicle by rotating the ratchet clockwise. Make sure \
the UP
marking faces you. Use the jack handle extensions if the flat tire is on the
rear
of the vehicle. Raise the vehicle far enough off the ground so there is
enough
room for the spare tire to fit.
5-27
ProCarManuals.com

PmMems on the Road
,. 8' ' I. - i: T ,.I - .. Front Rear
PO500
Lower the vehicle by rotating the ratchet counterclockwise. Lower the \
jack
completely.
r
K2546
Tighten the nuts firmly in a criss-cross sequence as shown. Rotate the ratchet
clockwise with the
UP marking facing you.
5-30
ProCarManuals.com

Pzloblenrs on the Road
Pull the retainer through the wheel center. Attach the ratchet,\
with the UP
side facing you, to the wheel wrench. Put the chisel end of the wheel wrench
into the hole in the rear bumper. Turn the ratchet until the tire is raised
against the underside
of the vehicle.
You will hear
two “clicks” when the tire is secure, but pull on the tire to
make sure.
Return the jack, ratchet, wheel wrench and jack extensions to their location
behind the passenger’s seat. Secure the items and replace th\
e jack cover
if
there is one.
Storing Tire ln Pickup Bed
K2534
1. Place the bolt through the bottom wheel nut hole. Be sure the valve
2. Place the nut on the bolt and turn it clockwise until the ti\
re is secure.
faces out.
532
ProCarManuals.com

Service & Appearance Care
I
IC Operating the engine with the air cleaner off can cause you or others
to be burned. The air cleaner not only cleans the air,
it stops flame
if the engine backfires. If it isn't there, and the engine backfires, you
could be burned. Don't drive with it
off, and be careful working on
the engine with the air cleaner
off.
If the air cleaner is off, a backfire can cause a damaging engine fire. And,
dirt can easily get into your engine, which will dan le
it. Alway! 3 tl
air cleaner in place when you're driving.
To remove the air cleaner filter on a gas engine, turn the wing nuts
counterclockwise. Remove the cover and change the filter.
fi 31 Fnning 6.5L Engine
K2151
On a 6.2L diesel engine there are two wing nuts. On a 6.5L \
diesel engine, unhook the clips.
6-32
ProCarManuals.com

Service & Appearance Care
Composite Headlights
A
1
I
PO234
1. Remove the two screws at the top of the radiator support.
2. Pull the composite headlight lens out.
3. Unplug the electrical connector.
4. Turn the bulb counterclockwise and remove it. ,
5. Put the new bulb in and turn it clockwise until it is tight.
6. Plug in the electrical connector.
7. Put the headlight back into the vehicle and tighten the two screws.
6-56
ProCarManuals.com

Front Parkinflurn Signal Lights
K2681
1. Remove the screws and take out the parking/turn signal light assembly.\

K2682
2. Squeeze the tab on the side of the light socket while turning the socket
counterclockwise.
3. Pull out the socket.
4. Push in gently on the bulb, turn it counterclockwise and remove it from
the socket.
6-57
ProCarManuals.com

Service & Amearance Care
5. Put the new bulb into the socket, gently press in on the bulb and turn it
clockwise until it is tight.
6. Put the socket back into the light assembly and turn it clockwise \
until it
locks.
7. Put the parkinghurn signal light assembly back into the vehicle\
and
tighten the screws.
Side Marker Bulb
II K2683
1. Remove the screws and pull out the parkinghurn signal light as\
sembly.
2. Reach through the opening and turn the side marker bulb socket
counterclockwise and remove it.
3. Pull the bulb straight out of the socket.
4. Put a new bulb into the socket and push it in until it is tight.
5. Put the socket back into the side marker assembly and turn it clockwise
to tighten it.
6. Replace the parkinghurn signal light assembly and tighten the s\
crews.
6-58
ProCarManuals.com

Fender Marker Lights
I
1. Remove the screws and take the lens assembly out of the fender.
2. Turn the bulb socket counterclockwise and remove it from the lens
3. Pull the bulb straight out of the socket.
4. Put a new bulb into the socket and push it in until it is tight.
5. Put the socket back into the lens assembly and turn it clockwise to
6. Replace the lens and tighten the screws.
assembly.
tighten it.
PO248
6-59
ProCarManuals.com