Downloaded from www.Manualslib.com manuals search engine
CONTROLS
AND EQUIPMENT
Ignition
lock
Petrol
engines
1 -
Ignition
off/engine
stationary
-
Steering
can be
locked
2
-
Ignition
on
3
-
Starting
engine
Diesel
engines
1 -
Fuel supply
cut
off/engine
sta
tionary
-
Steering can
be
locked
2
-
Glow
and
drive
position
No
other current consumers should
be
switched
on together with the glow plugs
-
this avoids draining the battery
unnecessar
ily.
3
-
Starting
engine
For
all
vehicles:
Position
1:
To
lock
the
steering
wheel
withdraw
key
and turn wheel until you hear the locking
pin engage.
Attention
Do
not
withdraw
key
from
lock
until
vehicle
is
stationary!
The
steering lock could
be
uninten
tionally
engaged.
Position
2: If
the key is difficult to turn in the lock or
can
not be turned to this position at
all,
the steer
ing wheel must be rocked
to
and fro slightly
to release the locking pin.
Position
3:
In this position
the
headlights
and
other
heavy
current consumers are switched
off.
Before
the starter can be operated again the
key
must be turned back
to
position 1. The
non-repeat
mechanism
in the
ignition lock
prevents
the
starter from being operated
when
engine
is
running, as this could
dam
age
the starter.
36
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS AND EQUIPMENT
2
-
Coolant temperature
—
~~s
gauge starts
to
work
when ignition
is
=
.vitched on,
but it
takes some time before
~e needle reaches
its
final position.
-en ignition
is
switched
on the
warning
c~ip flashes
for a few
seconds
as a
func-
•
:nal check.
5
- Cold
-. Did
high
engine speeds and
do not
work
r-gine
too
hard
yet.
:
- Normal
nen
the
vehicle
is
driven normally
the
~eedle
should settle
down
in
this zone.
-en engine
is
working hard and the ambi-
r~t
temperature
is
high,
the
needle
may
-ove
a
long
way up. This is not serious as long as the
warning lamp does not flash.
Warning lamp
If
the lamp flashes when driving, check first
the indicated coolant temperature.
If the
needle
is in the
normal zone,
top the
coolant
up at the
next
opportunity.
If
the reading
is
in the upper zone, either the
coolant level
is too low or the
coolant tem
perature
is too
high.
Stop,
switch
en
gine off
and
try to
find cause
of
trouble
-
see
page 47.
Notes
•
Additional
lights
in
front
of the cooling air intake interfere
with
the
flow
of cooling air. At
high
ambient
temperatures and
full
throttle
there is a danger that the engine
will
then
overheat.
3
-
Digital clock
*
To
set the
time there
are two
buttons
on
lower left
of
instrument cluster.
The
hours
are
set
with
the
upper button
(h) and the
minutes
with
the
lower one
(min):
•
If
pressed briefly, preferably
with
a ball
pen,
the time changes one hour
or
one min
ute.
•
If
pressed continuously the hours
or
min
utes
change continuously.
With
the minute button the clock can be set exactly
to the
second:
•
Press button until time shown
by
clock
is
one minute before time
to be set.
•
Press button
at the
moment when
the
seconds
indicator
of an
accurate clock
shows a full minute
or
when the time signal
is
heard
on the
radio.
41
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS
AND
EQUIPMENT
6-Alternator
Q
~ne warning lamp comes on when the
igni-
I
on
is
switched on and must go out when
She
engine
is
started.
i the warning lamp comes on when driving,
stop,
switch
engine
off
and
check
the
alternator V-belt.
f the V-belt
is
broken or loose do not
drive
on with
a
vehicle which
has a 4 cylinder
engine
because the coolant pump
is
then
no
longer being driven. The V-belt must
be
tensioned
or
renewed.
ehicles with
a 5
cylinder engine
can
nor
mally
be
driven to the nearest Volkswagen
dealer when
the
V-belt
is
broken
or
loose oecause
the
coolant pump
is
driven separ
ately but then the battery will discharge
con
tinuously
and all
non-essential electrical consumers should
be
switched
off.
f the warning lamp comes on although
the
belt
is
not broken, one can normally drive on
to
the nearest Volkswagen dealer (all engine
types)
but the
battery will then discharge
continuously
- see
previous paragraph.
7-Glow
plugs
W
(Diesel engines only)
When
the engine
is cold
the warning lamp comes on when key
is
turned to Drive
posi
tion
(ignition on).
If
the warning lamp does not come
on,
there
is
a
defect in the glow plug system
-
call
in
expert assistance.
When
the
lamp goes out,
start
the engine
immediately
-
see page
38.
When
the
engine
is warm the
glow plug
lamp
does
not
come on -the engine can
be
started straight
away.
(®)
-
Anti-locking
Brake
System
(ABS)*
The operational readiness
of the
essential electrical components
of the ABS are
checked,
both before moving off and when
driving,
by an electronic monitoring system.
The warning lamp lights up when
the
igni
tion
is
switched on and
it
must go out again, at the latest, after the engine
has
started.
If
the warning lamp does not go out
or if it
comes on when driving the system
is
not
in
order.
The
vehicle can then only
be
braked
with
the
normal system
-
that
is
without
ABS-.The vehicle must be taken to a Volks
wagen Dealership
as
soon
as
possible.
Further details on ABS
is
given on page
30.
<]1i>
-
Trailer
turn
signals
The warning lamp
*
flashes when turn
sig
nals are switched on when towing
a
trailer.
If a
turn signal fails on the trailer or vehicle,
the warning lamp does not flash.
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS AND EQUIPMENT
JB70-
1251
Switches
Notes
• On vehicles
with
righthand drive the ar rangement of the switches differs. The
symbols
on the switches are however the
same
as on vehicles
with
lefthand drive.
• The use of the lighting described here is subject to local regulations.
1 -
Lighting
switch
-n
First
detent -side lights11
Second
detent -headlight high/low beams
The
headlights only work when the ignition
is
on. When the engine is being started and
after ignition has been switched off, the headlights are switched off automatically.
When
the side lights are on, a warning lamp lights up in the switch.
When
the lights are on, the level of the in strument lighting can be regulated by turning the knurled disc on the
right
of the
switch.
Dipping and flashing the headlights - see
page
52. 2 -
Headlight
range
control
* %\_)
With the electrical range control the
head
light settings can be matched exactly to the
load
condition of vehicle. This prevents on
coming traffic from being
dazzled
more than
is
unavoidable. At the same time the correct headlight beam setting provides the best
possible
visibility for the driver.
The
headlights can only be regulated
with
the dipped headlights switched on.
To
lower the beams,
turn
knurled disc from
the
basic
position (-) downwards.
Note
The
basic
headlight setting (only possible
with
headlight adjusting appliance) must al
ways
be done
with
the headlight headlight range control knurled disc in the
basic
posi
tion (-) - see page 128
also.
On
vehicles for some export countries when
the side lights are switched on
with
the igni
tion switched on, the dipped headlights also
come
on
with
reduced intensity.
50
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS
AND
EQUIPMENT
3
-
Emergency lights .
nen the emergency lights are on, a warn-
'z lamp in the switch flashes as well.
Ine system also works when the ignition is
;
.-.itched off.
4
-
Knurled wheel for seat
^Jf
heating*
~~e cushion and backrest of the
front
seats
:
=
n
be heated electrically when the ignition
s
on.
_~e
heating is switched on and regulated .vth the knurled wheel.
•
switch heating off,
turn
knurled wheel to
:_e
left
to the detent position.
5
-
Heated rear window
QpJ
The
heating works only when ignition is on.
When
heater is on a lamp in the switch lights up.
As soon
as
window
is
clear,
switch element
off. The
reduced
current consumption helps
to re
duce
the
fuel
consumption
- see
also
page
80.
On
vehicles
with
electrically adjustable ex
terior mirrors the mirrors are heated as long
as
the rear window heating is switched on.
6
-
Fog lights •/
|Q
Rear fog light
First
detent - fog lights
Second
-
front
and rear fog
detent lights, or rear fog
light
only
At the second position a warning lamp in the switch comes on.
The fog lights
work
with
the side lights (ignition on), low or high beams.
The rear fog light
works only
with
the fog lights or
with
the low or high beams.
Due
to the amount of
dazzle
it
causes
the
rear
fog
light
should only be switched on
when the visibility is very poor (in Germany
for example, below 50 metres).
Note
The
electrical system of the factory
fitted
tow bar* is wired-up so
that
when towing
a
trailer
fitted
with
rear fog lights, the rear
fog
light
on the towing vehicle are automati
cally
switched off.
51
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS
AND EQUIPMENT
Turn signal and dip
lever
The
turn
signals only work when the ignition
is
switched on.
Right
turn
signals - lever up
Left
turn
signals - lever down
When
turn
signals are working, the warning lamp flashes as well - see page 48
also.
The
turn
signals cancel automatically after
completing a turn. To
signal
a
lane
change
Move
lever up or down to pressure point
and
hold in this position - the warning lamp must also be flashing.
To dip
headlights
Pull
lever past pressure point towards steer
ing wheel. When high beams are on, the
high beam warning light will light up.
Headlight
flasher
Pull
lever towards steering wheel to pres
sure
point - the high beam warning lamp lights up.
Parking
lights
The
parking lights only work when ignition
is
switched off.
Right
parking lights - lever up
Left parking lights - lever down. Note
The
use of the signals and lighting described
here
is subject to local regulations.
52
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS AND EQUIPMENT
Windscreen
wiper
and
washer
system
Wipers
and washers only work when igni
tion is switched on.
The
heated
windscreen
washer
jets*
are switched on when the ignition is switched on and the amount of heat is regulated automatically according to the ambi
ent temperature
When
it is freezing, check
that
the wiper
blades
are not frozen to the glass before
switching the wipers on for the
first
time.
Windscreen
• Flick
wipe
Lift lever to pressure point before detent 1.
•
Wiper
slow
Lever
at position 1. •
Wiper
fast
Lever
at position 2.
•
Intermittent
wipe
Lever
at position 3
The
wipers work about every 6
seconds.
With an
infinitely
variable
intermit
tent
wipe*
the wipe delay can be programmed between about 1.5 and 22
sec
onds:
- Switch on
intermittent
wipe
- Switch off
intermittent
wipe and then switch on again after the desired delay.
The
selected delay can be changed as often
as
required. After switching off the ignition
the selected pause reverts back to a six
sec
ond interval.
•
Automatic
wash/wipe
facility
Pull
lever towards steering wheel - wipers
and
washer work.
Release
lever -
The
washer stops and the wipers carry on
for about 4
seconds.
Headlight washer system*
When
the headlights are on, the lenses are
washed
every time the windscreen is
washed.
At regular intervals such as when filling the
tank, caked-on
dirt
and insects should be
removed.
Rear
window
Press
lever away from steering wheel and
release
- the wiper works about every 6
seconds
(intermittent
wipe).
Pressing
and
releasing
lever again switches the wiper off.
Automatic
wash/wipe
Press
lever away from steering wheel, and
hold in this position -
The
wiper and washer work as long as the
lever
is held in this position.
Release
lever -
The
washer stops and the wiper carries on
for about 4
seconds.
Notes
Topping-up washer fluid
- see page 108.
Changing
windscreen wiper blades
- see page 109
54
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS
AND
EQUIPMENT
Notes
Pools of
water
under
the
vehicle
• When the ambient temperature is high
and
the air very humid, condensed water
can
drip off the evaporator and form a puddle under the vehicle. This is quite nor
mal
and does not indicate a leak.
Operating
faults
• Should the air conditioner not work at
any
time, either:
- the ambient temperature is below about + 5 degrees C,
- the fuse has blown.
Check
fuse and if necessary renew it - see
page
122. If the trouble is not due to
a
defec
tive fuse, switch the system off and have it
checked.
- the air conditioner has switched off due to the coolant temperature being too high -
see
page 41
also.
• If the cooling
output
drops off, switch the
A/C
off and have the system
checked.
Using air
conditioner
economically
In cooling operation the air conditioner
com
pressor
places demands on the engine and
therefore influences the fuel consumption.
To
keep the period switched on as short as
possible,
the following points should be
noted:
• If the inside temperature is very high after the vehicle has been parked in the sun, it is recommended to open doors or win
dows
briefly to enable the hot air to
escape.
• The air conditioner should not be
switched
on during a journey if the windows
or
sliding/tilting
roof*
are open.
• If the desired interior temperature can be attained
without
switching on the air condi
tioner, the fresh air operation should be se
lected.
Recirculating
air
switch
If badly contaminated air is to be prevented
from entering the vehicle, e.g. when driving
through a tunnel, the recirculating air switch in the instrument panel can be
pressed.
When
the recirculating air system is
switched
on, a small warning lamp lights up in the switch.
However,
the recirculating air system
should
only be used for a short period other
wise
the windows will mist up.
60
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans