1992 MAZDA PROTEGE oil

IMPORTANT INFORMATION
IMPORTANT INFORMATION
BASIC ASSUMPTIONS
This workshop manual assumes that you have certain special tools that are necessary for the safe and effi-
cient performance of service operations on Mazda vehicles and that you know how to use them properly.
It also assumes that you are familiar with automobile systems and basic service and repair procedures. You
should not attempt to use this manual unless these assumptions are correct and you understand the conse-
quences described below.
SAFETY RISK
This manual contains certain notes, warnings, and other precautionary information that you should carefully
read and follow to reduce the risk of personal injury to yourself or others and the risk of improper service
that may damage the vehicle or render it unsafe. If there is no such information in regard to any specific
service method, this does not mean there is no possibility that personal safety or vehicle safety will be
jeopardized by the use of incorrect methods or tools.
POSSIBLE LOSS OF WARRANTY
The manufacturer’s warranty on Mazda vehicles and engines can be voided if improper service or repairs
are performed by persons other than those at an Authorized Mazda Dealer.
WARNING ON LUBRICANTS AND GREASES
Avoid all prolonged and repeated contact with mineral oils, especially used oils. Used oils contaminated
during service (e.g., engine sump oils) are more irritating and more likely to cause serious effects, including
skin cancer, in the event of gross and prolonged skin contact.
Wash skin thoroughly after work involving oil.
Protective hand cleaners may be of value provided they can be removed from the skin with water. Do not
use gasoline, paraffin, or other solvents to remove oil from the skin.
Lubricants and greases may be slightly irritating to the eyes.
Repeated or prolonged skin contact should be avoided by wearing protective clothing if necessary. Particu-
lar care should be taken with used oils and greases containing lead. Do not allow work clothing to be con-
taminated with oil. Dry clean or launder such clothing at regular intervals.
9MUGIX-002
GI-2

HOW TO USE THIS MANUAL GI
HOW TO USE THIS MANUAL
PREPARATION
PREPARATION points out the needed Special Service Tool (SST) for the service operation that it pro- m
ceeds. Gather all necessary
SST before beginning work.
Example:
49 0118 850C
removal of be-rod
9MUGIX-033
REPAIR PROCEDURE
1. Most repair operations begin with an overview illustration. It identifies the components, shows how the
parts fit together, and visual parts inspections. If a damaged or worn part is found, repair or replace it
as necessary.
2. Expendable parts, tightening torques, and symbols for oil, grease, and sealant are shown in the overview
illustration.
3. Pages related to service procedures are shown under the illustration. Refer to this information when ser-
vicing the related part.
Example:
SHOWS
NEEDED SST

SHOWS
APPLICATION
#T OF OIL,
SHOWS
RELATED
PAGE FOR
SERVICE ----

3. Bearing cup 1. Bolt
2. Lock Dlate
4. Adjusting screw
5. Bearing outer race
6. Locknut
7. Washer
8. Companion flange 16. Bearing Inner race
@ Removal. ,,,..,,,..
lnstallatlon page
page M--5 M-Z
i 7. Spacer
18. Drive pinion
Removal, .,,, ,.,, .,......... page M--i
Inspect spllnes and teeth for wear or damagl
Adjustment of height page M-2
Adurstp- w
SHOWS TIGHTENING
TORQUE
SPECIFICATION ‘2
SHOWS TIGHTENING
rORQlJE UNIT
SHOWS VISUAL
INSPECTION
INFORMATION
* 1: The numbering (ex.a) shows service procedure.
*2: Units shown in N.m (m-kg, ft-lb) unless otherwise specified.
9MUGIX-034
GI-3

HOW TO USE THIS MANUAL/FUNDAMENTAL PROCEDURES
SYMBOLS
There are six symbols indicating oil, grease, and sealant. These symbols show the points of applying such
materials during service.
Symbol Meaning Kind
Apply oil New engine oil or gear oil as appropriate
aI i . Apply brake fluid Only brake fluid
Apply automatic transaxle fluid Only ATF
Apply grease Appropriate grease
amal Apply sealant Appropriate sealant
0 Apply petroleum jelly Appropriate petroleum jelly
23UGIX-001
Note
l When special oil or grease is needed, this is shown in the illustration.
NOTES, CAUTIONS, AND WARNINGS
As you read through the procedures, you will come across NOTES, CAUTIONS, and WARNINGS. Each
one is there for a specific purpose.
NOTES give you added information that will help you to complete a
particular procedure.
CAUTIONS are given to prevent you from making an error that could damage the
vehicle. WARNINGS
remind you to be especially careful in those areas where carelessness can cause per-
sonal injury.
The following list contains some general WARNINGS you should follow when you work on
a vehicle.
9MUGIX-036
SMUGIX-037
a-4 FUNDAMENTAL PROCEDURES
PROTECTION OF THE VEHICLE
Always be sure to cover fenders, seats, and floor areas be-
fore starting work.

GI FUNDAMENTAL PROCEDURES
9MUGIX-04t 3
9MUGIX-041
9MUGIX.004
I
Depending on location:
1. Inspection of parts
When removed, each part should be carefully inspected for
malfunctioning, deformation, damage, and other problems.
2. Arrangement of parts
All disassembled parts should be carefully arranged for re-
assembly.
Be sure to separate or otherwise identify the parts to be
replaced from those that will be reused.
3. Cleaning parts for reuse
All parts to be reused should be carefully and thoroughly
cleaned in the appropriate method.
REASSEMBLY
Standard values, such as torques and certain adjustments,
must be strictly observed in the reassembly of all parts.
Refer to STANDARD BOLT AND NUT TIGHTENING TORQUE
in Section TD for tightening torques not mentioned in the main
text.
If removed, these parts should be replaced with new ones:
1. Oil seals 2. Gaskets
3. O-rings 4. Lock washers
5. Cotter pins 6. Nylon nuts
1. Sealant should be applied or new gaskets used.
2. Oil should be applied to the moving components of parts.
3. Specified oil or grease should be applied at the prescribed
locations (such as oil seals) before reassembly.
I
23lJGIX.004
GI-6

FUNDAMENTALPROCEDURES GI
I
67UOGX-00
ADJUSTMENTS
Use suitable gauges and/or testers when making adjustments.
EN
RUBBER PARTS AND TUBING
Prevent gasoline or oil from getting on rubber parts or tubing.
--.
GI-7

PRE-DELIVERY INSPECTION
PRE-DELIVERY INSPECTION
PRE-DELIVERY INSPECTION TABLE
Following items may be done at any time prior to delivery to your customer.
INSPECT and ADJUST, if necessary, the following items to
the specifications:
0 Glass, exterior bright metal and paint for damage
Cl Wheel lug nuts, and locks (if equipped)
88-118 N.m (9-12 m-kg, 65-87 ft-lb)
q All weatherstrips for damage or detachment
0 Operation of hood release and lock
0 Operation of trunk lid, rear hatch, and fuel lid opener
Cl With trunk open, check for spare jack, tire, tools, and
fasteners securing these items in place.
Cl Door operation and alignment
Cl Headlight aim
INSTALL the following parts:
Cl Wheel caps or rings (if equipped)
q Outside rearview mirror(s)
1 UNDER HOOD-ENGINE OFF )
INSPECT and ADJUST, if necessary, the following items to
the specifications:
0 Fuel, coolant and hydraulic lines, fittings, connections and
components for leaks
Cl Engine oil level
0 Power steering fluid level
0 Brake and clutch master cylinder fluid level
El Windshield washer reservoir fluid level
Cl Radiator coolant level
Cl Tightness of battery terminals
Cl Manual transaxle oil level
riizmiq
INSTALL the following parts:
Cl Rubber stopper for inside rearview mirror
CHECK operation of the following items:
0 Seat controls (sliding and reclining) and head restraint
Cl Folding rear seat
0 Door locks, including childproof door locks (if equipped)
Seat belts and warning system
Cl Ignition switch and steering lock
0 Inhibitor switch (ATX only)
U Starter interlock switch (clutch pedal, MTX only)
Cl All lights, including warning and indicator lamps
Cl Sound warning system
Cl Horn, wipers and washers (front and rear, if equipped)
0 Audio system (if equipped) 0 Cigarette lighter and clock
0 Sunroof (if equipped)
II Remote control outside rearview mirrors (if equipped)
Cl Power windows (if equipped)
q Heater, defroster and air conditioner at various mode
selections (if equipped)
CHECK the following items:
Cl Presence of spare fuse
0 Upholstery and interior finish
CHECK and ADJUST, if necessary, the following items:
0 Pedal height and free play of brake and clutch pedal
Pedal height mm (in) Free play mm (in)
0 Parking brake
5-7 notches/98 N (10 kg, 22lb)
UNDER HOOD-ENGINE RUNNING AT
OPERATING TEMPERATURE
CHECK the following items:
q Automatic transaxle fluid level
[I
CHECK the following items:
Cl Underside fuel, coolant and hydraulic lines, fittings, con-
nections and components for leaks
0 Tires for cuts or bruises
0 Steering linkage, suspension, exhaust system and all un-
derside hardware for looseness or damage
[I
CHECK the following items:
0 Brake operation
0 Clutch operation
Cl Steering control
Cl Operation of gauges
q Squeaks, rattles or unusual noise
Cl Emergency locking retractors
0 Cruise control system (if equipped)
1 AFTER ROAD TEST (
CHECK for necessary owner information materials.
Following items must be done just before the delivery to your customer.
q Load test battery and charge if necessary
1 Volts 1 0 Install fuses for accessories
i.. _
0 Adjust tire pressure to the specification
Load test result cl Remove seat and floor mat protective covers
(Refer to door label) 0 Vacuum and clean interior of vehicle
0 Clean outside of vehicle q Inspect installation of option parts with invoice
23UOAX-002
A-2

SCHEDULED MAINTENANCE SERVICES (EXCEPT CANADA)
Follow Schedule 1 (Normal Driving Conditions) if the vehicle is mainly operated where none of the following conditions apply.
Follow Schedule 2 (Unique Driving Conditions) if any of the conditions below apply:
l Repeated short-distance driving.
l Driving in dusty conditions.
* Driving with extended use of brakes.
* Driving in areas where road salt or other corrosive materials are used.
l Driving on rough and/or muddy roads.
l Extended periods of idling and/or low-speed operation.
l Driving for prolonged periods in cold temperatures and/or extremely humid climates.
Schedule 1 (Normal Driving Conditions)
Number of months or miles (kilometers), whichever comes first
Months 7.5 15 22.5 30 37.5 45 52.5 60
7.5 15 22.5 30 37.5 45 52.5 60
12 24 36 46 60 72 64 96 Service data and inspection points Page
Bl-5
B2-5
D-5
D-5
Bl-12
B2-12
F-79
G-18 MAINTENANCE
OPERATION
m Cracks or damage
B Tension
m Oil pan capacity
B6 SOHC: 3.0 liters (3.2 US qt, 2.6 Imp qt)
All BP : 3.6 liters (3.8 US qt, 3.2 Imp qt)
l Oil filter capacity:
0.17 liter (0.18 US qt, 0.15 Imp qt)
-
l Plug gap: 1.0-l .l mm (0.039-0.043 in)
l Recommended spark plugs
Engine NGK NIPPONDENSO
B6 SOHC BKR5E-11 KIGPR-Ull
BKRGE-11 K20PR-U 11
BP SOHC BKR5E-11 KlGPR-Ull
BKRGE-11 K20PR-U 11
BKR5E-11 KlGPR-Ull
BP DOHC BKRGE-11 K20PR-U 11
BKR7E-11 K22PR-Ull I I
R R R R R R R R
R R R R R R R R Drive belts
Engine oil
Oil filter
Engine timing belt*’
Air cleaner element Replace every 60,000 miles (96,000 km)
I
Spark plugs

y Schedule 2 (Unique Driving Conditions)
OPERATION
Drive belts MAINTENANCE / Number of months or miles (kilometers), whichever comes first
INTERVALS Months
5 IO 15 20 25 30 35 40 45 50 55 60
x 1,000 milea i 5 10 15 20 25 30 35 40 45 50 55 60
x 1,000 km 8 16 24 32 40 48 56 64 72
80 88 96
I I Service data and inspection points Page
l Cracks or damage Bl-5 l Tension B2-5
l Oil pan capacity
B6 SOHC: 3.0 liters (3.2 US qt, 2.6 Imp qt)
All BP : 3.6 liters (3.8 US qt, 3.2 Imp qt)
l Oil filter capacity: D-5
I I I I I I I I I I I
RRRRRRR R R R R R
Replace every 3,000 miles (4,800 km) or every 3 months
R R R R R RRRRRRR
0.17 liter (0.18 US qt, 0.15 Imp qt) Engine oil
Engine oil (For Puer-to-Rico)
Oil filter D-5
81-12
82-12
F-79
G-18 Replace every 60,000 miles (96,000 km)
Engine timing belt*’
Air cleaner element -
-
-
-
-
-
-
-
- -
-
-
-
-
-
-
-
-
FL
-
R
-
I
-
R
-
4 *;
-
-
*3
T
- -
-
-
-
-
-
-
-
- -
-
-
-
-
-
-
-
-
*2 -
-
-
-
-
-
-
-
- - R -
l Plug gap: l.O--l.lmm (0.039-0.043 in)
l Recommended spark plugs
Engine NGK NIPPONDENSO
B6 SOHC BKR5E-11
KlGPR-Ull
BKRGE-I 1 K20PR-U 11
BP SOHC BKR5E-I 1 KlGPR-Ull
BKRGE-11 K20PR-U 11
BKRSE-I 1 Kl GPR-Ul 1
BP DOHC BKRGE-11 K20PRUll
BKR7E-11 K22PR-U 11 R
Spark plugs
I
l Hoses for cracks or wear l Coolant level E-5
Cooling system
R
l Coolant capacity:
5.0 liters (5.3 US qt, 4.4 Imp qt) MTX
6.0 liters (6.3 US qt, 5.3 Imp qt) ...,,,,,. ATX
l ATX: P range, MTX: Neutral E-6
Engine coolant
A
-
R
-
I
-
I Idle speed , F-80
F-124 / 700-800 rbrn (with parkina brake applied) -
- -
- , , I .I
-
Fuel filter
l Fittings, connections, and components for
leaks
l Prooer attachment and connections F-120
- Fuel lines
Brake lines. hoses and connections