1992 MAZDA PROTEGE light

TRANSAXLE Jl
1. Control rod
2. Control end
3. lstl2nd shift fork
4. Control lever
5. Interlock sleeve
6.3rd/4th shift fork
7. Clutch hub
8. Synchronizer key
9. Clutch hub sleeve
10. Synchronizer spring
11. Clutch housing
12. Differential assembly
13. Secondary shaft gear assembly
Assembly Note . . . . . . . . . . . . . . . . . . . . . . . . . . page Jl-45
14. Primary shaft gear assembly
Assembly Note.. . . . . . . . . . . . . . . . . . . . . . . , . page J 1-45
15. Spring
16. Steel ball
17. Shift fork and shift rod assembly
Assembly Note.. . . . . . . . . . . , . . . . . . . . . , . . , page J 1-45
18. Crank lever assembly
Assembly Note. . . . . . . . . . . . . . . . . . . . . . . . . . page Jl-46
19. Crank lever shaft
Assembly Note.. . . . . . . . . . . , , . . . . . . . . . . . . page Jl -46
20. Pin
21. 5th shift rod end
Assembly Note . . . . . . . . . . . . . . . . . . . . . . . . . . page 31-46
22. 5th shift rod
Assembly Note.. . . . . . . . . . . . . . . . . . . . . . . . . page J 1-46
23. Reverse idler gear
Assembly Note . . . . . . . . . . . . . . . . . . . . . . . . . . page Jl-46
24. Reverse idler shaft
Assembly Note... . . . . . . . . . . . . . . . . . . . . . . . page Jl -46
25 Magnet
26. Transaxle case assembly
Assembly Note.. . . . . . . . . . . . . . . . . . . . . . . . . page Jl -47
27. Neutral switch
28. Back-up light switch
29. Lock bolt and washer
30. Secondary 5th gear
31. Gear sleeve
32. 5th gear
33. Synchronizer ring (5th)
34. Clutch hub assembly (5th)
Assembly Note.. . . . . . . . . . . . . . . . . . . . . . . . . page Jl-47
35. 5th shift fork
Assembly Note . . . . . . . . . . . . . . . . . . . . . . . . . . page Jl-47
36. Stop plate
37. Locknut (Secondary shaft)
Assembly Note.. . . . . . . . . . . . . . . . . . . . . . . . . page Jl-47
38. Locknut (Primary shaft)
Assembly Note.. . . . . . . . . . . . . . . . . . . . . . . . . page J 1-47
39. Rear cover
13UOJl-005
Assembly note
Primary shaft gear assembly and secondary shaft gear
assembly
1. Install the primary shaft gear assembly and the secondary
shaft gear assembly together.
03UOJl-115 Shift fork and shift rod assembly
1. Shift to 2nd gear and position the shift fork and shift rod
assembly as shown.
03UOJ2-088
51-45

TRANSAXLE Jl
1. Transaxle
Installation Note ..,......,.............. page Jl-49
2. Engine mount No.4
3. Driveshaft
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page Jl-50
4. Stabilizer (BP SOHC)
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page Jl-50
5. Tie-rod end
Installation Note ,........,..,........... page Jl-50
6. Clutch release cylinder
7. Engine mount No.2
8. Exhaust pipe
9. Engine mounting member
Installation Note . . . . . . . . . . . . . . . . . . . . . . . .
page Jl-50
10. Control rod
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page Jl-51 11. Extension bar
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . page Jl-51
1 12. Starter
13. Ground
Installation Note .,..,...,......,........ page Jl-5
14. Neutral switch connector
15. Back-up light switch connector
16. Speedometer cable
Installation Note . . . . . . . . . . . . . . . . . . . . . . . .
page Jl-5
17. Battery carrier
18. Battery
19. Air hose and resonance chamber
20. Splash shield
21. Wheel and tire 1
Installation Note
Transaxle
1. Set the transaxle on a jack and lift it into place.
Install tne transaxle oorts.
Tightening torque:
64-69 N*rn (6.5-9.1 m-kg, 47-66 ft-lb)
Loosely tighten engine mount No.4 bolts.
Jl-49

TRANSAXLE J2
1. Wheel and tire 14. Exhaust pipe
2. Splash shield 15. Engine mount No.2
3. Air hose and resonance chamber 16. Clutch release cylinder
4. Battery Removal Note .,...........,....,.,...... page J2-11
5. Battery carrier 17. Tie-rod end
6. Speedometer cable Removal Note . . . . . . . . . . . . . . . . ..*........ page J2-11
7. Back-up light switch connector 18. Stabilizer
8. Neutral switch connector 19. Driveshaft
9. Ground Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-12
10. Starter 20. Joint shaft
11. Extension bar 21. Engine mount No.4
12. Control rod 22. Transaxle
13. Engine mount member Removal Note ..,..,....*................ page J2-12
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-1 1
03UOJ2-014
-
03UOJ2-01
Removal Note
Engine mount member
1. Suspend the engine with the SST and remove the engine
mount member.
Clutch release cylinder
Caution
l Do not damage the clutch pipe.
1. Remove the bolts shown.
2. Lay aside the clutch release cylinder and the clutch pipe.
I ,
03UOJ2-016
Tie-rod end
1. Remove the cotter pin.
Caution
l Do not damage the dust boot.
2. Loosen the nut and disconnect the tie-rod end with the SST.
I I
03UOJ2-017
52-l 1

TRANSAXLE J2
Clutch Housing and Transaxle Case Components
Caution
l Do not remove an oil seal if not necessary.
1. Disassemble in the order shown in the figure, referring to Disassembly Note.
ACE
1. Bearing outer race (Primary shaft) 19. Oil seal (differential)
2. Oil seal Replacement (On-vehicle) . . . . . . . . . page J2-16
3. Bearing outer race (Secondary shaft) 20. Bearing outer race (differential)
Disassembly Note . . . . . . . . . . . . . . . . . . . . . page J2-16 Disassembly Note . . . . . . . . . . . . . . . . . . . . . page J2-16
4. Funnel 21. Reverse lever shaft
5. Guide plate 22. Reverse lever
6. Change arm 23. Drain plug and washer
7. Roll pin 24. Neutral switch and gasket
Disassembly Note . . . . . . . . . . . . . . . . . . . . . page J2-16 25. Bearing outer race (transaxle case)
8. Change rod assembly Disassembly Note . . . . . . . . . . . . . . . . . . . . . page J2-16
9. Boot 26. Diaphragm spring
10. Spring 27. Adjust shim
11. Reverse gate 28. Bearing outer race (differential)
12. Selector Disassembly Note . . . . . . . . . . . . . . . . . . . . . page J2-16
13. Oil seal 29. Adjust shim(s)
14. Bleeder cover 30. Oil seal (differential)
15. Bleeder Replacement (On-vehicle) . . . . . . . . . page J2-16
16. Speedometer driven gear assembly 31. Back-up light switch
Inspection ..,.,,.,......,................... page J2-24 32. Oil passage
17. Driven gear 33. Joint
18. Gear case 34. Change rod
52-l 5

TRANSAXLE J2
Clutch Housing and Transaxle Case Components
1. Select the adjust shim(s), referring to Bearing Preload Adjustment.
2. Assemble in the order shown in the figure, referring to Assembly Note.
3. Verify that the bearing preload is satisfied after assembly, referring to Bearing Preload.
-s
APPLY SPECIFIED OIL TO INDIVIDUAL PARTS EXCEPT SWITCHES
&II N.m (SO-110 cm-kg, SO-95 In-lb)
20-29
P-3,
@NEW=
O-RING, I
14-22) 11
R N.m (120-160 cm-kg,
104-l 39 in-lb)
A
=SELECTlVE ROLL PIN NE
(120-140 cm-kg,
SELECTIVE 20-29 (2-3, 14-22)
N.m (m-kg,
??I 1
1. Change rod 16. Oil seal
2. Joint
3. Oil passage
4. Back-up light switch
5. Oil seal
Assembly Note . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-35
6. Adjust shim(s)
Bearing preload adjustment . . . . . page J2-32
Bearing preload . . . . . . . . . . . . . . . . . . . . . . . . page J2-36
7. Bearing outer race
8. Adjust shims
Bearing preload adjustment . . . . . page J2-32
Bearing preload . . . . . . . . . . . . . . . . . . . . . . . . page J2-36
9. Diaphragm springs
Assembly Note . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-35 Assembly Note . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-35
17. Gear case
18. Driven gear
19. Speedometer driven gear assembly
20. Bleeder
21. Bleeder cover assembly
22. Oil seal
23. Selector
24. Reverse gate
25. Spring
26. Boot
Assembly Note ,.,....................... page J2-35
27. Change rod assembly
28. Roll pin
10. Bearing outer races
11. Neutral switch and gasket
12. Drain plug and washer
13. Reverse lever
14. Reverse lever shaft
15. Bearing outer race 29. Change arm
30. Guide plate
31, Funnel
32. Bearing outer race
33. Oil seal
34. Bearing outer race
J2-31

TRANSAXLE J2
INSTALLATION
1. Raise the vehicle and support it with safety stands.
2. Install in the order shown in the figure, referring to
Installation Note,
3. Fill the transaxle with the specified amount of the specified transaxle oil after installation.
4. Warm up the engine and transaxle, and inspect for oil leakaae and transaxle ooeration.
37-52 (3.8-5.3, 27-38) 37-52 (3.8-5.3, 27-38)
9.8-12 (1.0-1.2, 7.2-8.7)
7.8-l 2 (0.8-l .2, 5.8-8.7)
1. Transaxle
6. Tie-rod end
2. Engine mount No.4 7. Clutch release cylinder
3. Joint shaft
8. Engine mount No.2
4. Driveshaft
9. Exhaust pipe
Installation Note
10. Engine mount member
. . . . . . . . . . . . . . . . . . . . .
page J2-42 11. Control rod
5. Stabilizer
12. Extension bar
Installation Note 13. Starter
. . . . . . . . . . . . ..______. page J2-42 14. Ground
31-48 (3.2-4. ‘8
88-l 18 (g-12,65-87)
(6.5-9.1, 47-88)
37-52 (3.8-5.3, 27-38)
N.m (m-kg, Mb)
15. Neutral switch connector
16. Back-up light switch
connector
17. Speedometer
cable
18. Battery carrier
19. Battery
20. Air hose and resonance
chamber
21. Splash shield
22. Wheel and tire
52-41

DRIVE SHAFT
8. Apply the specified grease included in the kit to the tripod
joint, outer ring, and boot. Install the outer ring.
9. If the wheel-side boot was removed, fill with the specified
grease included in the kit.
Specified grease
!J@z)
B6 SOHC BP SOHC BP DOHC
Right Left Right
Left Right Left
side side side side side side
DIFFEREN- 2;&y’ 140 (4.94) 145 (5.12)
TIAL SIDE y;L44;)
YELLOW YELLOW YELLOW
WHEEL SIDE 70 (2.47) 140 (4.94) 90 (3.18)
BLACK BLACK BLACK
23UOMX-03
I I
I
23UOMX-0:
M-28
Caution
l Be sure the boots are not dented or twisted.
. Carefully lift up the small end of the boots to release
any trapped air.
10. Install the boots.
11. Measure the length of the drive shaft.
Standard length: mm (in)
B6 SOHC BP SOHC BP DOHC
MTX 1 ATX MTX 1 ATX MTX 1 ATX
light side 919.3 918.7
630.7
(36.19) (36.17) (24.83)
640.2 621.2 637.1
(25.20) (24.46) (25.08)
I Left side
I 637.8
(25.11)
12. Fold the new bands back by pulling on the ends with pliers.
13. Lock the ends of the bands by bending the locking clips.

P CONVENTIONAL BRAKE SYSTEM
03UOPX.01
03UOPX-01
03UOPX-01
23UOPX-0
BRAKE FLUID
Inspection
Leakage inspection
Depress the brake pedal several times, and inspect for leak-
age of the brake line system. __,
Brake Fluid Level
Leakage check
Verify that the fluid level in the reservoir is between the MAX
and MIN lines on the reservoir.
Add fluid if it is below MAX.
Replacement
1. Follow the procedure outlined in Air Bleeding.
(Refer to page P-6).
2. Continue bleeding and replacing the brake fluid until only
clean fluid is expelled.
3. Fill the reservoir to the MAX level.
BRAKEPEDAL
Inspection, On-vehicle
Brake pedal height
Inspection
Verify that the distance from the center on the pedal pad to
the floor mat is as specified.
Specification: 193-196mm (7.60-7.72 in)
Adjustment
1. Disconnect the stoplight switch connector.
2. Loosen locknuts @J and turn switch @ until it does not con-
tact the pedal.
3. Loosen locknuts (I?J and turn rod @ to adjust the height
of the brake pedal.
4. Tighten the stoplight switch until it contacts the pedal; then
turn it an additional 112 turn. Tighten locknuts @ and @I.
5. Connect the stoplight switch connector.
6. Verify operation of the stoplights.
P-8