1992 MAZDA PROTEGE wheel

M REAR AXLE
DISC BRAKE TYPE
Preinspection
Wheel bearing play
1. Remove the wheel and tire.
2. Remove the brake caliper assembly.
3. Position a dial indicator against the wheel hub. Push and
pull the wheel hub by hand in the axial direction and meas-
ure the wheel bearing play.
4. If the bearing play exceeds specification, check and adjust
the locknut torque or replace the wheel bearing if necessary.
-I 5 Maximum wheel bearing play: 0.05mm (0.002 in)
Removal / Inspection / Installation
1. Remove in the order shown in the figure, referring to Removal Note.
2. Inspect all parts and repair or replace as necessary.
3. Install in the reverse order of removal, referring to
Installation Note.
4. After installation. check the rear wheel alianment (Refer to Section R.)
45-61
(4.6-6.2, 33-45)
-118
-12.0,
-87)
REPLACE
16-23
(1.6-2.3, 12-17)
N-m (m-kg, ft-lb]
311 InMY-nif4
1. Wheel and tire
2. Hub cap
3. Locknut
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M-15
4. Brake caliper assembly
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..~ Section P
5. Disc plate
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section P 6. Hub bearing assembly
Inspect for cracks and damage
Disassembly I Assembly . . . . . . . . . . . . page M-l 5
7. Dust cover
8. Rear spindle
Inspect for cracks and damage
M-14

DRIVE SHAFT
JOINT SHAFT (BP DOHC)
Preinspection
Joint shaft
1. Verify that the joint shaft is not twisted or cracked. Replace
it if necessary.
2. Turn the joint shaft by hand and verify that the bearing ro-
tates smoothly and freely. Replace it if necessary. .___,
23UOMX-019
Removal / Installation
Note
l Drain the transaxle oil before removal.
1. Remove in the order shown in the figure, referring to Removal Note.
2. Install in the reverse order of removal, referring to Installation Note.
r
1
vi5
42-62
7.8-11 N.m
(80-l 10 cm-kg,
69-95 in-lb)
4L59
I (9.0-12.0, 66-87)
(4.4-6.0, 3243)
0
N.m (m-kg, ft-lb)
311 Inh.4Y.A’
1. Wheel and tire
2. Splash shield
3. Stabilizer (BP SOHC, BP DOHC)
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M-19
4. Tie rod end
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . page M-19
Installation Note ..,...................... page M-19 5. Lower ball joint
6. Right drive shaft and axle
7. Joint shaft
Removal Note .,.,...,....,,.,.,..,..,..,. page M-19
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M-19
Overhaul . . . . . . . . . . . . . . . .,......*...
. . . . . . . . . page M-m .
M-18

M
Removal / Installation
DRIVE SHAFT
Note
l Drain the transaxle oil before removal.
1. Remove in the order shown in the figure, referring to Removal Note.
2. Install in the reverse order of removal, referring to Installation Note.
7.8-11 N-m
(80-I 10 cm-kg,
N.m (m-kg, ft-lb]
011 InhdYJwG
1. Wheel and tire
2. Splash shield
3. Locknut
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M-24
4. Stabilizer
Installation Note ..,,.....,...,........... page M-24
5. Tie rod end
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . page M-23
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . . page M-23 6. Lower ball joint
7. Drive shaft (Left)
Removal Note ,....,., . . . . . . . . . . . . . . . . . . . . page M-23
Installation Note . .., . . . . . . . . . . . . . . . . . . . . . page M-23
Overhaul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page M-25
8. Drive shaft (Right)
Removal Note .,.. ,., ,.... . . . . . . . . . . . . . . . . page M-23
Installation Note . . . . . . . . . . . . . . . . . . . . . . . . .
page M-23
Overhaul . ,...................... . . . . . . . . . . . . page M-25
M-22

DRIVE SHAFT M
23UOMX-04
23UOMX-02
I
23UOMX-02
/
I
23UOMX-029
23UOMX-04
Removal note
Tie rod end
Caution
l Do not damage the dust boot.
1. Loosen the nut and disconnect the tie rod end with the SST.
Drive shaft
Caution
l Do not damage the dust cover or oil seal.
1. Remove the drive shaft from the transaxle with a pry bar.
Note
l If the drive shaft is stuck in the front wheel hub, in-
stall a miscellaneous nut until it is flush with the end
of the shaft. Tap the nut with a copper hammer to
remove the drive shaft.
Installation note
Drive shaft
Caution
l Do not damage the dust cover or oil seal.
1. install the drive shaft with the end-gap of clip facing upward.
Tie rod end
Caution
l Do not damage the dust boot.
1, Install the nut and secure it with the new cotter pin.
Tightening torque:
42-57 N-m (4.3-5.8 m-kg, 31-42 ft-lb)
M-23

DRIVE SHAFT M
Overhaul
Caution
l Do not remove the U-shaped bearing outer races from the outer ring. (BP SOHC Left drive shaft)
l Secure the joint in a vise with protective material (such as copper plates) on the vise jaws.
l Be careful that dust or other foreign material does not enter the joint while the work is being
performed.
l Do not disassemble the wheel-side ball joint.
l Do not wash the joint unless it is being disassembled.
1. Disassemble in the order shown in the figure, referring to Disassembly Procedure.
2. Inspect all parts and repair or replace as necessary.
3. Assemble in the reverse order of disassembly, referring to Assembly Procedure.
I
23UOMX-030
1. Boot band 8. Band
2. Boot band 9. Dynamic damper
3. Clip 10. Boot band
4. Outer ring 11. Boot band
Inspect inside bore for wear, corrosion, and 12. Boot
scoring 13. Shaft and ball joint assembly
5. Snap ring Inspect splines for damage and wear
6. Tripod joint Inspect wheel-side joint for excessive play
7. Boot and rough rotation
M-25

DRIVE SHAFT M
I
I 03UOMX-053
DIFFERENTIAL SIDE WHEEL SIDE
23UOMX-03 1
03UOMX.05
23UOMX :-032
23UOMX
Caution
l Do not remove the wheel side boot if not necessary.
12. Pry up the locking clips of the wheel-side boot bands with
a screwdriver.
13. Remove both bands with pliers. Remove the boot.
Assembly procedure
Caution
l The wheel-side and transaxle-side boots are
different.
mm (in)
I c3
80.8
I 89.0 85.2
(3.18) (3.50)
I I 94.1
(3.35) (3.70)
1. Wrap the splines of the transaxle-side shaft, and install the
wheel-side boot.
Caution
l Always use new bands.
l The bands should be mounted in the direction op-
posite the forward revolving direction of the drive
shaft.
2. Install the dynamic damper and new band.
3. Fold the band back by pulling on the end of it with pliers.
4. Lock the end of the band by bending the locking clip.
5. Install the wheel-side boot.
Caution
l Do not damage the bearing.
6. Align the marks and install the tripod joint with a bar and
a hammer.
7. Install the new snap ring with snap-ring pliers.
M-27

DRIVE SHAFT
8. Apply the specified grease included in the kit to the tripod
joint, outer ring, and boot. Install the outer ring.
9. If the wheel-side boot was removed, fill with the specified
grease included in the kit.
Specified grease
!J@z)
B6 SOHC BP SOHC BP DOHC
Right Left Right
Left Right Left
side side side side side side
DIFFEREN- 2;&y’ 140 (4.94) 145 (5.12)
TIAL SIDE y;L44;)
YELLOW YELLOW YELLOW
WHEEL SIDE 70 (2.47) 140 (4.94) 90 (3.18)
BLACK BLACK BLACK
23UOMX-03
I I
I
23UOMX-0:
M-28
Caution
l Be sure the boots are not dented or twisted.
. Carefully lift up the small end of the boots to release
any trapped air.
10. Install the boots.
11. Measure the length of the drive shaft.
Standard length: mm (in)
B6 SOHC BP SOHC BP DOHC
MTX 1 ATX MTX 1 ATX MTX 1 ATX
light side 919.3 918.7
630.7
(36.19) (36.17) (24.83)
640.2 621.2 637.1
(25.20) (24.46) (25.08)
I Left side
I 637.8
(25.11)
12. Fold the new bands back by pulling on the ends with pliers.
13. Lock the ends of the bands by bending the locking clips.

N
STEERING SYSTEM
INDEX ......................................................
MANUAL STEERING ............................... ;I g
ENGINE SPEED SENSING POWER
STEERING (ESPS) ................................. N- 3
OUTLINE ..................................................
SPECIFICATIONS .................................... ;I ::
MANUAL STEERING ..................................
PREPARATION ....................................... ;I ;
TROUBLESHOOTING GUIDE.. .................. N- 5
BOOT ................................................... N- 6
STEERING WHEEL AND COLUMN.. .......... N- 6
STEERING GEAR AND LINKAGE .............. N-13
ENGINE SPEED SENSING POWER
STEERING .............................................. N-23
PREPARATION ....................................... N-23
TROUBLESHOOTING GUIDE.. .................. N-25
AIR BLEEDING ....................................... N-26
STEERING WHEEL AND COLUMN.. .......... N-26
POWER STEERING FLUID.. ...................... N-27
STEERING GEAR AND LINKAGE .............. N-30
POWER STEERING OIL PUMP.. ................ N-37
DRIVE BELT ........................................... N-41
23UONX-001