1992 MAZDA PROTEGE engine

Bl ASSEMBLY
CYLINDER BLOCK (EXTERNAL PARTS)
Torque Specifications
19-25
(1.9-2.6, 14-19)
GASKET, NEW
OIL SEAL,
NEW
7.6-11 N.m
(60-l 10 cm-kg,
69-95 in-lb)
GASKET, NE
16-21 (1.6-2.1, 12--15)-j
R
A -22% / 7.6-11 N.m
(60-110 cm-kg, 69-95 in-lb) 6-103 w
,..6-10.6,
71-76) 16-26
(1.6-2.7, 13-20)
7.6-11 N-m
(60-110 cm-kg, 69-95 in-lb)
N.m (m-kg, R-lb)
Bl-74
OWOBX-201 0
Rear Cover
1. Apply a small amount of clean engine oil to the lip of a new
oil seal.
2. Push the oil seal slightly in by hand.
Caution
l The oil seal must be pressed in until it is flush with
the edge of the rear cover.
3. Press the oil seal in evenly with a suitable pipe.
Oil seal outer diameter: 1OOmm (3.94 in)
4. Apply silicone sealant to the shaded area shown in the
figure.

ASSEMBLY Bl
OWOBX-20
23UOBl-049
5. Install the rear cover.
Tightening torque:
7.8-l 1 N*m (80-l 10 cm-kg, 89-95 in-lb)
Oil Pump
1. Apply a small amount of clean engine oil to the lip of a new
oil seal.
2. Push the oil seal slightly in by hand.
Caution
l The oil seal must be pressed in until it is flush with
the edge of the oil pump body.
3. Press the oil seal in evenly with a suitable pipe.
Oil seal outer diameter: 44mm (1.73 in)
4. Install the oil pump and a new gasket.
Tightening torque:
19-25 N-m (1.9-2.8 m-kg, 14-19 ft-lb)
Caution
l Do not scratch the oil pump.
5. Cut away the portion of the gasket that projects from the
body toward the oil pan side.
Main Bearing Support Plate (MBSP)
1, Remove all foreign material from the contact surfaces of the
cylinder block and the MBSP.
Caution
l The oil pan must be secured within 5 minutes after
the sealant is applied to the MBSP.
2. Apply silicon sealant to the shaded areas shown in the figure.
81-75

Bl ASSEMBLY
Cylinder Head Gasket
1. Remove all foreign material from the top of the cylinder
block.
2. Place the new cylinder head gasket in position.
05UOBX-219
36 SOHC
Cylinder Head
1. Install the cylinder head.
2. Apply clean engine oil to the bolt threads and seat faces
3. Tighten the cylinder head bolts in two or three steps in the
order shown.
Tightening torque:
76-81 N.m (7.7-8.3 m-kg, 56-80 ft-lb)
3P SOHC OWOBX-221
03UOBl-205
Camshaft Oil Seal
1. Apply a thin coat of engine oil to the camshaft oil seal and
cylinder head.
2. Tap the camshaft oil seal into the cylinder head with a suita-
ble pipe.
Caution
. The oil seal must be tapped in until it is flush with
the cylinder head.
Oil seal outer diameter: 40mm (1.57 in)
--
Bl-82

ASSEMBLY Bl
BP SOHC
THRUST PLATE
DOWEL PIN AND PIN GROOVE
63UOlX-121
63UOlX-12
01; RESERVOIR
03UOBl-1’ 16
Camshaft
1. Apply engine oil to the journals and bearings; then insert
and mount the camshaft into position with the thrust plate.
Tightening torque:
7.8-l 1 N-m (80-l 10 cm-kg, 89-95 In-lb)
Camshaft Pulley
1. Install the camshaft pulley onto the dowel pin with the pin
groove facing straight upward.
Note
l Be certain that the dowel pin of the camshaft also
faces straight upward.
2. Tighten the camshaft pulley bolt. Hold the camshaft using
a suitable wrench on the cast hexagon as shown.
Tightening torque:
49-81 N-m (5.0-8.2 m-kg, 38-45 ft-lb)
Hydraulic Lash Adjuster (HLA)
1. Pour engine oil into the oil reservoir in the rocker arm.
2. Apply engine oil to the new HLA.
3. install the HLA in the rocker arm.
Caution
l Be careful not to damage the O-ring when installing.
81-83

ASSEMBLY Bl
AUXILIARY PARTS
Torque Specifications
DRIVE BELT
INSTALLATION
PAGE Bl-6 19-25 (1.9-2.6, 14-19)
w-113 (9.5-11.5, 69-83) I _______ _ - ..- - -,
(3.8-5.3, 27-38)
19-25 Il.9-2.8. 14- 37-63 (3.8-6.4, 27-46)
15-23 (1.5-2.3, 11-17)
N.m (m-kg, ft-It
OWOBX-2
03UOBl.16
Engine Hanger
1. Install the front and rear engine hangers.
Tightening torque
Front: 37-63 N-m (3.8-6.4 m-kg, 27-46 ft-lb)
Rear: 19-25 N.m (1.9-2.6 m-kg, 14-19 ft-lb)
81-89

Bl ASSEMBLY
05UOBX-24:
Spark Plug
1. Install the spark plugs.
Tightening torque:
15-23 N*m (1.5-2.3 m-kg, 1 I-17 ft-lb)
Oil Level Gauge
1. Install the oil level gauge.
Oil Pressure switch
1. Install the oil pressure switch.
Tightening torque:
12-18 N-m (120-180 cm-kg, 104-158 in-lb)
Oil Filter
1. Remove all foreign material from the oil filter mounting
surface.
2. Apply a small amount of clean engine oil to the rubber seal
of the oil filter.
3. Install the oil filter and tighten it by hand until the rubber
seal contacts the base.
4. Tighten the filter 1 and l/6 turns with a filter wrench.
No.3 Engine Mount Bracket
1. Install the No.3 engine mount bracket.
Tightening torque:
93-l 13 N-m (9.5-l 1.5 m-kg, 89-83 ft-lb)
Alternator
1. Install the alternator strap.
Tightening torque:
37-52 N#m (3.8-5.3 m-kg, 27-38 ft-lb)
2. Install the alternator and alternator drive belt. Loosely tight-
en the alternator installation bolt.
3. Adjust the drive belt deflection. (Refer to page Bl-6.)
Tightening torque
Alternator installation bolt @ :
37-52 N-m (3.8-5.3 m-kg, 27-38 ft-lb)
Belt-adjusting bolt @ :
19-25 N#m (1.9-2.8 m-kg, 14-19 f&lb) --’ I
I 0311081-165
Bl-90

ASSEMBLY Bl
03UOBl-16
03UOB1.21 38
Injector and Distribution Pipe Assembly (BP SOHC)
1. Install the injector and distribution pipe assembly with new
insulators.
Tightening torque:
19-25 N-m (1.9-2.6 m-kg, 14-19 ft-lb)
Intake Manifold Assembly
1, Remove all foreign material from the intake manifold con-
tact surface.
2. Install a new gasket and the intake manifold assembly.
Tightening torque:
19-25 N*m (1.9-2.6 m-kg, 14-19 ft-lb)
Distributor and High-tension Lead
1. Apply engine oil to the O-ring, and position it on the dis-
tributor.
2. Apply engine oil to the blade.
3. Install the distributor with the blade fit into the camshaft
groove.
4. Temporarily, loosely tighten the distributor installing bolt.
5. Adjust the ignition timing after engine installation.
(Refer to Section G.)
6. Connect the high-tension leads.
81-91

Bl ENGINE STAND DISMOUNTING
ENGINE STAND DISMOUNTING
PROCEDURE
1. Remove the engine from the SST (engine stand).
2.
Remove the SST (engine hanger) from the engine.
3. Install the parts shown in the figure.
Torque Specifications
19-25 11.9-2.6. 14-191
(3.8-5.3, 27-38)
52 (3.8-5.3, 27-38)
7.0111 N-m
(80-110 cm-kg, 69-95 in-lb)
T- :p,;f W-23 (1.6-2.3, 12-17)
19-25 (1.9-2.6, 14-19)
N-m (m-kg, Mb)
OWOBX-25‘
Water Inlet Pipe
1. Remove all foreign material from the water inlet pipe mount-
ing surface.
2. Install a new gasket and the water inlet pipe.
Tightening torque:
19-25 N-m (1.9-2.6 m-kg, 14-19 ft-lb)
-,
03UOBl-169
81-92