1992 MAZDA PROTEGE oil pressure

ENGINE SPEED SENSING POWER STEERING
23UONX-06:
23UONX-06
(4) Tighten the locknut with the SST.
(5) Measure the pinion starting torque with the SST and
a pull scale.
Starting torque .-/
At f 90° from the straight-ahead position:
1.0-l .3 N-m (lo-14 cm-kg, 8.7-12 in-lb)
(Pull scale reading: 1.0-l .4 kg [35.3-49.4 oz])
At other position:
1.6 N,m (17 cm-kg, 14.7 in-lb) max.
(Pull scale reading: 1.7 kg [3.7 lb] max.)
(6) If not as specified, repeat Steps (3) to (5).
10. Tie rod
(1) Install the new washers to the tie rods.
(2) Install the tie rods with the
SST.
Tightening torque:
59-78 N,m (6-6 m-kg, 43-58 ft-lb)
(3) Band the washers.
Note
l Install the tie rod (with air bled out) at the rack hous-
ing side.
ll.Boot
(1) Install the boot, boot wire and boot clip.
12. Tie rod end
(1) Install the locknut and the tie rod end.
13. Oil pipe
(1) Install the oil pipes.
Tightening torque
Cylinder pipe: 20-29 N.m
(2-3 m-kg, 14-22 ft-lb)
Pressure and return pipe:
29-39 N.m (3-4 m-kg, 22-29 ft-lb)
14. Mounting bracket and mounting rubber (tube side)
(1) Install the mounting rubber and the bracket (tube side)
to the gear housing.
N-36

ENGINE SPEED SENSING POWER STEERING
POWER STEERING OIL PUMP
N
Removal / Installation
1. Remove in the order shown in the figure.
2. Install in the reverse order of remnvnl
. ..-.-..
d 2 19-25 (1.9-2.6, 14-19)
- Nm (m-kg, f&lb)
23UONX-043
1. Bolt
2. Nut
3. Nut
4. Adjusting bolt
5. Drive belt
Replacement .,....,.,.,,,,.,.....,..,,.... page N-42
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page N-42
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
page N-41 6. Pressure hose
7. Return hose
8. Bolts
9. P/S oil pump assembly
N-37

N ENGINE SPEED SENSING POWER STEERING
Disassembly / Inspection / Assembly
1. The following procedures show replacement of the O-rings. If a problem is found in other parts, replace
the oil pump assembly.
2. Disassemble in the order shown in the figure, referring to
Disassembly Note.
3. Inspect all parts and replace as necessary.
4. Assemble in the reverse order of disassembly, referring to
Assembly Note,
1. Suction pipe
2. O-ring
3. Pressure-switch assembly
4. O-ring
5. Connector
6. O-ring
7. Control valve
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page N-40
8. Spring
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page N-40
9. Bracket
10. Pump body (rear)
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page N-39
Il. O-ring _,
12. Cam ring
Assembly Note . . . . . . . . . . . . . . . . . . . . . . . . . . . page N-39
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page N-40
13. Vane
Assembly Note . . . . . . . . . . . . . . . . . . . . . . . . . . . page N-39
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page N-40
14. Rotor
Assembly Note . . . . . . . . . . . . . . . . . . . . . . . . . . page N-39
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page N-40
15. Side plate
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page N-40
16. O-ring
17. O-ring
18. Pin
19. Pump body (front)
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page N-39
N-38

CONVENTIONAL BRAKE SYSTEM
TROUBLESHOOTING GUIDE
Problem Possible cause Remedy Page
Poor braking
Leakage of brake fluid Repair P- 7
Air in system Bleed air P- 6
Worn pad or lining Replace P-l 8,23,28
Brake fluid, grease, oil, or water on pad or lining Clean or replace P-18,23,28
Hardening of pad or lining surface or poor contact Grind or replace P-l 8,23,28
Malfunction of disc brake piston Replace P-l 9,24
Malfunction of master cylinder or wheel cylinder Repair or replace P-l 0,21,26,
28,30
Malfunction of power brake unit Repair or replace P-16
Malfunction of check valve (vacuum hose) Replace P-15
Damaged vacuum hose Replace -
Deterioration of flexible hose Replace -
Malfunction of dual proportioning valve Replace P-17 Brakes pull to one
Worn pad or lining Replace P-l 8,23,28 side Brake fluid, grease, oil, or water on pad or lining Clean or replace -
Hardening of pad or lining surface or poor contact Grind or replace
Abnormal wear or distortion of disc, drum, pad, or lining Repair or replace P-l 8;3,28
Malfunction of automatic adjuster Repair or replace -
Looseness of backing plate I dust cover mounting bolts Tighten Section M
Malfunction of wheel cylinder Repair or replace P-21,26,30
Improperly adjusted wheel alignment Adjust Section R
Unequal tire air pressures
Adjust Section Q Brakes do not
No brake pedal play Adjust P- 9 release Improperly adjusted push rod clearance Adjust P-11
Clogged master cylinder return port Clean -
Weak brake pad or shoe return spring Replace -
Wheel cylinder not returning properly
Clean or replace
Malfunction of piston seal of disc brake Replace P-l;,24
Excessive runout of disc plate
Replace P-20,25 Pedal goes too far
Improperly adjusted pedal play Adjust P- 9 (too much pedal Worn pad or lining
Replace P-18,23,28 stroke) Air in system
Bleed air P- 6 Abnormal noise or
Worn pad or lining
Replace P-18,23,28 vibration during Deteriorated pad or lining Grind or replace - braking Brakes do not release Repair -
Foreign material or scratches on disc plate or drum con- Clean -
tact surface
Looseness of backing plate / dust cover or caliper Tighten
Section M,
mounting bolts P-l 9,24
Damaged disc or drum contact surface Replace -
Poor contact of pad or fining Repair or replace
P-18,23,28
Insufficient grease on sliding parts Grease - Steering wheel pulls
Dragging brake Repair - to one side Malfunction of steering system -
Section N
Damaged or unbalanced wheel(s) -
Section Cl
Incorrect tire pressure -
Section Q
Malfunction of suspension -
Section R
mm> IAn\, ,.e
P-5

WHEELS AND TIRES
WHEELS AND TIRES
SPECIAL NOTES ABOUT WHEELS AND TIRES
1. Do not use wheels or tires other than the specified types.
2. Aluminum wheels are easily scratched. When washing them, use a soft cloth, never a wire brush. If the
vehicle is steam cleaned, do not allow boiling water to contact the wheels.
3. If alkaline compounds (such as saltwater or road salts) get on aluminum wheels, wash them as soon as
possible to prevent damage. Use only a neutral detergent.
9MUOQX-004
NOTES REGARDING TIRE REPLACEMENT
Note the following points when tires are to be removed from or mounted onto the wheels.
1. Be careful not to damage the tire bead, the rim bead, or the edge of the rim.
2. Use a wire brush, sandpaper, or cloth to clean and remove all rust and dirt from the rim edge and the
rim bead.
3. When cleaning aluminum wheels, use a soft cloth, never a wire brush or sandpaper.
4. Remove any pebbles, glass, nails, and other foreign items embedded in the tire tread.
5. Be sure the air valve is installed correctly.
6. Apply a soapy solution to the tire bead and the edge of the rim.
7. After mounting a tire onto a wheel, inflate the tire to 250-300 kPa (2.55-3.06 kg/cm2, 35.55-42.66
psi). Check to be sure that the bead is seated correctly onto the rim and that there are no air leaks. Then
reduce the pressure to the specified level.
8. If a tire iron is used to change a tire on an aluminum wheel, be sure to use a piece of rubber between
the iron lever and the wheel to avoid damage to the wheel. Work should be done on a rubber mat, not
on a hard or rough surface.
03UOQX-004
23UOOX-003
TIRE
I
AIR VALVE
INSPECTION / ADJUSTMENT
Air Pressure
Air pressure
Check the air pressure of all tires, including the spare tire, with
an air pressure gauge. If necessary, adjust the air pressure.
Tire Size Air Pressure kPa (kgf/cm2, psi)
Front Tires Rear Tires
P155180R13 79s
PI 75/70R13 82s 216 (2.2, 32) 216 (2.2, 32)
P185/60R14 82H
1115/70D14 415 (4.2, 60)
Air Leakage
Verify that there is no air leakage from the air valve.
I I 13UOOX-008
Q-3

WHEEL ALIGNMENT
WHEEL ALIGNMENT
PRE-INSPECTION
1. Check the tire inflations and set to the recommended pressure, if necessary.
2. Inspect the front wheel bearing play; replace the bearing if necessary.
3. inspect the wheel and tire runout.
4. Inspect the ball joints and steering linkage for any excessive looseness.
5. The vehicle must be on level ground and have no luggage or passenger load.
6. The difference in height between the left and right sides from the center of the wheel to the fender brim
must not exceed
10mm (0.39 in).
7. Shake the vehicle to check operation of the shock absorbers.
03UORX.007
FRONT WHEEL ALIGNMENT
Specifications
item
Specifications
Maximum Inner 4o” f: 2O
steering angle Outer
33O f 2O
Total mm (in) 2 f 3 (0.08 f 0.12)
toe-in dearee 0.20 f 0.30 Wheel alignment
(*‘Unladen) Front
*I Fuel tank full; radiator coolant and Camber angle -0005 * 45’
Caster angle 1°55’ f 55’
Kingpin angle 12O25’
engine oil at specified level; and spare tire, jack, and tools in designated positions.
23UORX-008
I
I 23UORX-023
Adjustments
Maximum steering angle
1. Loosen the left and right tie rod locknuts, then turn the tie
rods equally.
Maximum left/right difference: 3mm (0.12 in)
2. Tighten the tie rod locknuts.
Tightening torque:
34-50 N-m (3.5-5.1 m-kg, 25-37 ft-lb)
3. Adjust the toe-in after adjusting the steering angle.
4. Inspect and adjust the toe-in after adjusting the turning angle.
I 23UORX-024
R-7

WARNING SYSTEM T
13UOTX-07
63U15X-05
, I//
‘nF -
-
-
FUEL
13UOTX.08C
- CHARGE
13UOTX-08
13UOTX-08
Inspection
Brake system warning lamp
1. Disconnect the connector from the brake fluid level sensor.
2. Connect a jumper wire between “G/Y” and “6” terminal
(body ground).
3. Start the engine and check that the BRAKE warning lamp
illuminates.
Caution
l Be sure that the parking brake is fully released be-
fore checking.
4. If there is no illumination, check the fuse, bulb, and wiring
harness.
Brake fluid level sensor
Connect an ohmmeter to each terminal of the brake fluid lev-
el sensor connector.
Check for continuity when the float is moved up and down.
The sensor is good if there is continuity when the float is be-
low the “MIN” mark, and if there is no continuity when the
float is above the “MAX” mark. If the sensor does not pass
this test, replace it.
Fuel-level warning lamp
1. Disconnect the connector from the fuel tank unit.
2. Connect the connector terminal “W/R” to the body ground.
3. Start the engine and check that the FUEL warning lamp il-
luminates.
4. If there is no illumination, check the fuse, warning lamp, and
wiring harness.
Alternator warning lamp
1. Start the engine, connect the connector terminal “W/B” to
a body ground.
2. Check that the alternator warning lamp illuminates.
3. If there is no illumination, check the warning lamps, wiring
harness and alternator. Replace or repair as necessary.
Engine oil pressure warning lamp
1. Disconnect the connector from the oil pressure switch.
2. Start the engine and connect the connector terminal “Y/R”
to a body ground.
3. Check that the “OIL” warning lamp illuminates. If it does
not, replace the sender switch or repair the wiring harness
if bulb is not burnt out.
T-61

2L BUZZER 2A 28 2C 2D 1A 3K l--r nnmn
I I‘ I
1C 3L 2E 2G IL iG 1F 1D tB
3F 38 3G 1E 3D
l-l rt
II l-l
l-l It II l-l 1J 11 1H
1G IF 1E 1D 1C 1B 1A 2L 2K 2J 21 2H 2G 2F 2E 2D 2C 28 2A
r-l It ,I 3L 3K 3J 31 3H 3G 3F 3E 3D 3C 3B 3A
Ter- I I minal Connected to 1 1A Combination switch
1B Ground
IC Fuel tank unit
1 ID 1 EGI control unit
I
II L 1J 1
L Ter-
minal Connected to
2A Speed sensor output
28 Light switch (high beam)
2C Turn switch (L)
20 Turn switch (R)
2E Ground
2F Ground
2L 1 IGI battery Ter-
minal Connected to
3A
38 Alternator
3c
30 Oil pressure switch
3E
3F Parking brake switch, Brake fluid switch
3G Passive shoulder belt control unit
3H h
I 31
3J
3K
IG2 battery
3L Water temperature gauge unit