1992 MAZDA PROTEGE wiring

TROUBLESHOOTING GUIDE F
21 RUNS ROUGH ON DECELERATION/BACKFIRE
IESCRIP.
*Engine runs rough while decelerating and abnormal combustion occurs in exhaust system
MON l Transaxle in normal condition TROUBLESHOOTING HINTS]
1) Arr/Fuel mixture too rich
l Arr cleaner element clogged
l Fuel injection control malfunctron
(Fuel cut control)
l Injector fuel leakage
*Throttle sensor (IDL terminal) malfunction
l Dashpot malfunctron
er with ignition switch ON
Check ECU terminal 1F voltage w page F-150
Specification: Battery voltage
(Ignition switch ON)
+ If OK, replace ECU w page F-149 6 If not OK, check wiring between
ECU and Self-Diagnosis Checker
----~
Check for cause (Refer to specified
check sequence) w page F-106
SELECT SW: A Vacuum: More than 450 mmHg (17.7 inHg)
tern components
4 Check if air cleaner element is clean Yes
Go to next step w page F-79
No
Replace air cleaner element
5 Check if ECU terminal voltages are OK
Yes Go to next step
MTX...Especially lN, 2A, 2U and 2V
ATX... Especially lT, 3A, 3U and 3V CT page F-150
No Check for cause c=i‘ page F-151
F-69

22 KNOCKING
DESCRIP- *Abnormal combustion accompanied by audible “pinging” noise
I-ION
[TROUBLESHOOTING HINTS]
3 Incorrect ignition timing (Too advanced)
@ Air/Fuel mixture too lean
3 Carbon deposits in cylinder
*Fuel injection amount not correct
3 Overheating
l Fuel line pressure decreases while accelerating
TEP INSPECTION
ACTION
1 Connect System Selector to diagnosis connector
Yes Go to next step
and set Test Switch to “SELF TEST” and check
for correct ignition timing at idle after warm-up
CT page F-79
Ignition timing (BTDC)
l BP DOHC : go-1 1 o l BP SOHC : 4”-6O
’ B6 No
Adjust a page F-79
2 Check if “00” is displayed on Self-Diagnosis
Yes Go to next step
Checker with ignition switch ON
W page F-62
No
Service Code No. displayed
Check for cause (Refer to specified
check sequence) w page F-63
“88” flashes
Check ECU terminal 1F voltage CT page F-150
Specification: Battery voltage
(Ignition switch ON)
c3 If OK, replace ECU w page F-149
W: SELF TEST c3 If not OK, check wiring between
ECU and Self-Diagnosis Checker
3 Check for correct intake manifold vacuum at idle
Yes Go to next step
VaCUUm: More than 450 mmHg (17.7 inHg) No
Check for air leakage of intake air sys-
tem components
4
Check for correct engine compression
Yes Go to next step
w page Bl-10
B2-10
Engine compression (Minimum):
l BP DOHC
883 kPa (9.0 kg/cm’, 128 psi)-300 rpm
l BP SOHC
834 kPa (8.5 kg/cm*, 121 psi)300 rpm
l B6
932 kPa (9.5 kg/cm’, 135 psi)300 rpm No High compression
Check engine condition CI page 81-10
62-l 0 l Carbon deposits
F-71

TROUBLESHOOTING GUIDE F
23 FUEL ODOR
DESCRIP-
*Gasoline odor in cabin
TION [TROUBLESHOOTING HINTS]
@ Poor connection or damaged at fuel system or evaporative emission control system
@ Charcoal canister overflow due to evaporative emission control System malfUnCtiOn
Check for cause (Refer to specified Specification: Battery voltage
(Ignltlon switch ON)
c3 If OK, replace ECU r;+ page F-149 c3 If not OK, check wiring between
ECU and Self-Diagnosis Checker
control) with engine running and throttle valve
opened (Neutral switch connector disconnected)
eck if vacuum is felt
s
23UOFX-029
F-73

TROUBLESHOOTING GUIDE F
26 POOR FUEL ECONOMY
DESCRIP-
l Fuel economy unsatisfactory TION
[TROUBLESHOOTING HINTS]
While fuel consumption is drastically increased by city driving, short-run operation, stop and go driving, extended winter
warm-up periods, etc., as opposed to “trip” mileage, an attempt should be made to determine these factors when con-
fronted with “poor mileage” conditions. However, since the operator is not always at fault, the following is offered.
@II Operator depressing accelerator more than usual due to
@ Air/Fuel mixture too rich
low engine power
l Poor ignition *High fuel line pressure
@ Alcohol blended fuel used
*Low intake air amount
l Electronic spark advance control system malfunction @ High vehicle load l Low tire pressure
*Clutch slipping/ATX slipping l Incorrect tire size l Exhaust component restricted l Brake dragging ;TEP
INSPECTION ACTION
1
Check factors other than engine Yes
Go to next step
l Low tire pressure = Section Q 9 Unrecommended tire srze v Section Q l Clutch slipping w Section H l Brake dragging No
0 Section P Repair
l Exhaust component restricted cz= page F-136
2
Check if air hoses are connected correctly - Yes
Go to next step CI page F-109
No
Repair 3
Check if “00” IS displayed on Self-Diagnosis
Yes
Checker with ignition switch ON Go to next step W page F-82 No
SYSTEM SELECT: 1 Service Code No. displayed Check for cause (Refer to specified
check sequence) w page F-63
“88” flashes
Check ECU terminal 1F voltage w page F-150
Specification: Battery voltage
(Ignition switch ON)
* If OK, replace ECU CT= page F-149 e If not OK, check wiring between
ECU and Self-Diagnosis Checker 4
Check for correct intake manifold vacuum at idle
Yes Go to next step Vacuum: More than 450 mmHg (17.7 inHg) No
Check for air leakage at intake air sys-
tem components 5
Check if air cleaner element is clean Yes
Go to next step CT= page F-79
No
Replace air cleaner element
F-75

TROUBLESHOOTING GUIDE
27 MIL ALWAYS ON
DESCRIP- *Self-Diagnosis Checker does not indicate Malfunction Code No. but MIL always ON
TION
[TROUBLESHOOTING HINTS]
*Short circuit in wiring harness
l ECU malfunction
iTEF 1
1
-
s
Disconnect (Y/B) wire from ECU and check if
MIL goes off
‘YIB
ATX YIB
INSPECTION ACTION
Yes Replace ECU CT page F-149
No Check for short circuit in wiring be-
tween instrument cluster and ECU
23UOFX-042
28
MIL NEVER ON
IESCRIP- *Self-Diagnosis Checker indicates Malfunction Code No. of input device but MIL never ON
RON *Other indicator and warning lamps OK
:TROUBLESHOOTING HINTS]
b Bulb burned
‘Open circuit in wiring harness
m ECU malfunction
TEP INSPECTION
ACTION
1 Ground (Y/B) wire at ECU with jumper wire and
Yes Check connection of ECU connector
check if MIL comes on
MTX e If OK, replace ECU w page F-149
I- i -!~ !r--~r’:~;-‘;- --~_:- ,
1 i r 1 1 1 ;-.:,~;~$~& {-;&# ,$&]j 4 If not OK, repair ECU connector
! No
Check if bulb is OK
ATX 13 If OK, repair (Y/B) wire between
ECU and instrument cluster
e If not OK, replace bulb CT page T-83
23UOFX-043
29 A/C DOES NOT WORK
DESCRIP- *Blower fan operates but magnet clutch does not operate
TION
[TROUBLESHOOTING HINTS]
*Open or short circuit in wiring harness
*A/C relay, A/C switch, or magnetic clutch malfunction
l ECU malfunction
TEP/ INSPECTION ACTION
1 1 Check ECU
terminal 10 (MTX) 10 (ATX) voltage 1
Yes Check ECU terminal 1 J (MTX) 1 L (ATX)
OK
CT= page F-152
MTX
T7J++!;i”-
L
ATX
No voltage OK
CT page F-152
1-3 If OK, check A/C system
c3- page U-30
~3 If not OK, replace ECU CT page F-149
Check for cause w page F-153
F-77

SELF-DIAGNOSIS FUNCTION F
PREPARATION
SST
49 6019 9AO
System Selector For
diagnosis 49 HO18 9Al
Self-Diagnosis
Checker For
diagnosis
SERVICE CODE NUMBER
Inspection Procedure
1. Connect the SST to the diagnosis connector.
2. Set switch @to position 1.
3. Set TEST SW to SELF-TEST position.
23UOFX-048
03UOFX.059
I
4. Connect the SST to the System Selector and a ground
5. Set the select switch to position A.
6. Turn the ignition switch to ON.
7. Verify that 88 flashes on the digital display and the buzzer
sounds for 3 sec. after turning the ignition switch ON.
8. If 88 does not flash, check the main relay (FUEL INJ relay)
(Refer to page F-172) power supply circuit, and diagno-
sis connector wiring.
9. If 88 flashes and the buzzer sounds continuously for more
than 20 sec., check for a short circuit between the engine
control unit terminal 1 F and the diagnosis connector. Re-
place the engine control unit if necessary and perform Steps
3 and 7 again.
23UOFX-049 IO. Note any code numbers and check for the causes by refer-
ring to the check sequences shown on pages F-88
through F-103. Repair as necessary.
Note
l Cancel the code numbers by performing the after-
repair procedure following repairs.
(Refer to page F-104.)
I 23UOFX-050
F--83

F SELF-DIAGNOSIS FUNCTION
Troubleshooting
If a service code number is show on the SST, check for the cause by using the chart related to the code
number shown.
r c :ODE No. -
iTEl
I 02 (DISTRIBUTOR Ne-SIGNAL)
INSPECTION I
ACTION
1
1
2
Check if Code No.03 is also present
-5- Check terminal-wire for continuity
4
Check if battery voltage exists at distributor
terminal-wire
-i-- Check terminal-wire between distributor and
ECU terminal 2E (MTX) 2A (ATX) for continuity
and ground
6
Cl$c; ,if$CU terminal 2E (MTX) 2A (ATX) volt- Yes Replace ECU
w page F-149
w page F-152 . No
Go to next step
7
I I
Check if OV or 45V--55V exists at distributor 1 Yes 1 Reolace distributor I
8
- Check distributor circuit for poor connection Yes
1 I Repair or replace connector
I
No SOHC
Go to Step 3
DOHC
Go to next step
Yes Go to next step I
No Go to Step 5
Yes
I I Go to next step
I
No
I I
Repair or replace
Yes Go to next step
No Check for open circuit in wiring from
distributor to main relay (FUEL INJ
relay)
Yes Go to next step
No Repair or replace
terminal-wire (W)
No Go to next step
Check if 4.5V-5.5V exists at ECU terminal 2E
(MTX) 2A (ATX) (With distributor connector dis-
connected) Yes Check for short circuit in wiring from
distributor to ECU
No Replace ECU CT page F-149
.-I 4
F-86

F SELF-DIAGNOSIS FUNCTION
r C :ODE No.
03 (DISTRIBUTOR G-SIGNAL) - DOHC ¶
El
i- I
INSPECTION
Check distributor circuit for poor connection ACTION
Yes Repair or replace connector
1
2
-s-
-T-
--c
--if-
7
-ii- No
I I Go to next step
Check if Code No.02 is also present Yes
I I Go to next step
Check terminal-wire for continuity No Go to Step 5
Yes Go to next step
Check if battery voltage exists at distributor
terminal-wire No Repair of replace
Yes Go to next step
No
I I
Check for open circuit in wiring from
distributor to main relay
Check terminal-wire between distributor and
Yes Go to next step
ECU terminal 2G (MTX) 2J (ATX) for continuity
and ground
No Repair or replace
Ct$; if$CU terminal 2G (MTX) 2J (ATX) volt- Yes Replace ECU r=+ page
F-149 CT page
F-154 No
Go to next step
Check if OV or 4.5V--53 exists at distributor Yes
I I Replace distributor
terminal-wire
No
I I Go to next step
I Check if 4.5V--5.5V exists at ECU terminal 2G
(MTX) 2J (ATX) (With distributor connector dis-
connected) Yes Check for short circuit in wiring from
distributor to ECU
No Replace ECU CT page
F-149
I I 23UOFX-0: i5
F-88