1992 MAZDA PROTEGE wheel

WHEEL ALIGNMENT
WHEEL ALIGNMENT
PRE-INSPECTION
1. Check the tire inflations and set to the recommended pressure, if necessary.
2. Inspect the front wheel bearing play; replace the bearing if necessary.
3. inspect the wheel and tire runout.
4. Inspect the ball joints and steering linkage for any excessive looseness.
5. The vehicle must be on level ground and have no luggage or passenger load.
6. The difference in height between the left and right sides from the center of the wheel to the fender brim
must not exceed
10mm (0.39 in).
7. Shake the vehicle to check operation of the shock absorbers.
03UORX.007
FRONT WHEEL ALIGNMENT
Specifications
item
Specifications
Maximum Inner 4o” f: 2O
steering angle Outer
33O f 2O
Total mm (in) 2 f 3 (0.08 f 0.12)
toe-in dearee 0.20 f 0.30 Wheel alignment
(*‘Unladen) Front
*I Fuel tank full; radiator coolant and Camber angle -0005 * 45’
Caster angle 1°55’ f 55’
Kingpin angle 12O25’
engine oil at specified level; and spare tire, jack, and tools in designated positions.
23UORX-008
I
I 23UORX-023
Adjustments
Maximum steering angle
1. Loosen the left and right tie rod locknuts, then turn the tie
rods equally.
Maximum left/right difference: 3mm (0.12 in)
2. Tighten the tie rod locknuts.
Tightening torque:
34-50 N-m (3.5-5.1 m-kg, 25-37 ft-lb)
3. Adjust the toe-in after adjusting the steering angle.
4. Inspect and adjust the toe-in after adjusting the turning angle.
I 23UORX-024
R-7

WHEEL ALIGNMENT
Camber and Caster
1, Jack up the front of the vehicle and support it with safety
stands.
2. Remove the mounting block nuts.
-
1 BUORX-01
23UORX-0;
3. Push the mounting block downward, and turn it to the
desired position.
Direction indicator
position
A
: Difference from standard position
Camber angle Caster angle
+14’ +14’
+29’ O0
+14’ -14’
4. Install and tighten the mounting nuts to the specified torque.
Tightening torque:
29-40 Nnrn (3.0-4.1 m-kg, 22-30 ft-lb)
Total toe-in
1. Loosen the left and right tie rod locknuts, then turn the tie
rods equally.
Caution
l The left and right tie rods are both right threaded,
so, to increase the toe-in, turn the right tie rod to-
ward the front of the vehicle and the left tie rod
equally toward the rear.
l One turn of the tie rod (both sides) changes the toe-
in by about 6mm (0.24 in).
2. Tighten the tie rod locknuts.
Tightening torque:
34-50 N-m (3.5-5.1 m-kg, 25-37 ft-lb)

WHEEL ALIGNMENT
REAR WHEEL ALIGNMENT
Specifications
kern Specifications
Total mm (in) 2 f 3 (0.08 f 0.12)
Wheel alignment
(*‘Unladen) Rear toe-in
degree 0.2O f 0.3O
Camber angle -0020’ f 45’
*I Fuel tank full; radiator coolant and engine oil at specified level; and spare tire, jack, and tools in designated positions.
13UORX-012
Adjustment
Total toe-in
1. Loosen the lateral link locknuts.
2. Turn the lateral link adjustment link to adjust.
Note
l One turn of the link changes 11.3mm (0.44 in).
3. Tighten the lateral link locknuts to the specified torque.
Tightening torque:
55-64 N,m (5.6-6.5 m-kg, 41-47 ft-lb)
R-9

R
FRONTSHOCKABSORBERANDSPRING
Removal / Installation
1. Jack up the front of the vehicle and support it with safety stands.
2. Remove the wheels.
3. Remove in the order shown in the figure.
4. Install in the reverse order of removal, referring to Installation Note.
5. After installation, measure the front wheel alignment, and adjust it if necessary.
Caution
l Retighten the shock absorber lower bolts to the specified torque after lowering the vehicle
(unladen condition).
1. Clip
2. Nut
3. Bolt
4. Nut 5. Shock absorber and spring
N.m (m-kg, R-lb
23UORX-0‘
- .^
Disassembly ............................... page H-l Z
Inspection ................................... page R-l 3
Assembly.. .................................. page R-14
Installation Note.. ........................ page R-12
R-l 1

FRONT SUSPENSION (STRUT)
FRONT LOWER ARM
Removal / Inspection / Installation
1. Jack up the front of the vehicle and support it with safety stands.
2. Remove the wheels.
3. Remove in the order shown in the figure, referring to
Removal Note.
4. Visually inspect each part and replace as necessary.
5. Install in the reverse order of removal, referring to
Installation Note.
6. After installation, measure the front wheel alignment, and adjust it, if necessary.
Caution
l Retighten the lower arm bolt and nuts to the specified torque after lowering the vehicle (un-
laden condition).
@G-l27 (SE,-12.9, M-93) @
I ‘&43h (4.4-6.0, 32-43)
b 93-127 (9.6-12.9, W-93)
N-m (m-kg, It-lb:
23UORX-O(
1. Stabilizer nut 9. Lower arm bushing (Rear)
Installation Note . . . . . . . . . . ..I............. page R-17 10. Nut
2. Retainer, bushing, spacer 11. Bolt
3. Stabilizer bolt 12. Lower arm ball joint
4. Bolt, washer Inspection . . . . . . . . . . . . . . . . . . ..*..*..........* page R-17
5. Bolt 13. Ball joint dust boot
6. Bolt, nut Removal I Installation Note......... page R-17 .--
7. Nut 14. Lower arm bushing (Front)
8. Washer 15. Lower arm
R-16

R FRONT SUSPENSION (STRUT)
FRONT STABILIZER
Removal / Inspection / Installation
1. Jack up the front of the vehicle and support it with safety stands.
2. Remove the wheels.
3. Remove the undercover.
4. Remove in the order shown in the figure, referring to
Removal Note.
5. Visually inspect each part and replace as necessary.
6. Install in the reverse order of removal, referring to
Installation Note.
Caution
l Retighten the stabilizer bracket bolts to the specified torque after lowering the vehicle (un-
laden condition).
@ 37-52 (3.8-5.3, 27-38)
N.m (m-kg, R-lb:
23UORX-0’
1. Stabilizer nut 5. Stabilizer bracket
Installation Note . . . . . . . . . . . . . . . . . ..*...... page R-19 6. Stabilizer bushing
2. Retainer, washer,
spacer
3. Stabilizer bolt
4. Bolt installation Note .,.....,..,...,........... page 11-19
7. Stabilizer bar
Removal / installation Note . . . . . . . . . page R-l 9
R-l 8

REAR SUSPENSION (STRUT)
REAR SHOCK ABSORBER AND SPRING
Removal / Installation
R
1. Jack up the rear of the vehicle and support it with safety stands.
2. Remove the wheels.
3. Remove in the order shown in the figure.
4. Install in the reverse order of removal.
5. After installation, measure the rear wheel alignment, if necessary.
Caution
l Retighten the shock absorber lower bolts to the specified torque after lowering the vehicle
(unladen condition).
.
/
2940 (3.0-4.1, 22-30)
‘I I L 93-127 (9.5-12.9, 69-93)
/
N-m (m-kg, R-lb)
23UORX-01’
1. Clip
5. Shock absorber and spring
2. Nut Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page R-22
3. Bolt Inspection ..__._.._ page R-23
4.
Nut Assembly.. . , . , . , , . , . . . . . . . . . . . . . . . . . . . . . . . . . page R-24
R-21

R REAR SUSPENSION (STRUT)
LATERAL LINK AND TRAILING LINK
Removal / Inspection / Installation
1. Jack up the rear of the vehicle and support it with safety stands.
2. Remove the wheels.
3. Remove in the order shown in the figure.
4. Visually inspect each part and replace as necessary.
5. Install in the reverse order of removal, referring to
Installation Note.
6. After installation, measure the rear wheel alignment, and adjust it if necessary.
Caution
0 Retighten the lateral link and trailing link mounting bolts and nuts to the specified torque af-
ter lowering the vehicle (unladen condition). -
63-93 (6.4
65-l 17 (6.7-l
93-127 (9.5-12.9, 69-93)
N-m (m-kg, R-lb
-^. .^-.. ^
1. Stabilizer nut 4. Cap
Installation Note 5. Nut
. . . . . . . . . . . . . . . . ...‘... page R-27 6. Washer
2. Retainer, bushing, spacer 7. Bolt
3. Stabilizer bolt 8. Retainer 9. Lateral link (front)
10. Lateral link (rear)
11. Bolt, washer
12. Trailing link
x?AJuux-u
R-26