1992 MAZDA 323 light

UUTLINE
RADfATOR GRfLtE
l The air inlet area of the radiator grille is enlarged for improved cooling efficiency.
FRONT BUMPER
l The large front bu,mper includes fog lights and bumper mesh to give the vehicle a dynamic appearance.
l tight and rigid polyurethane is used for the bumper fascia.
l The air inlet area is adopted for improved cooling efficiency.
s-4
REAR SKI
l The rear 5
l Light and
WHEEL AR4
l Wheel arc

OUTLINE S
REAR SKIRT
13EOSX-308 l The rear skirt is added for improved vehicle aerodynamics.
l Light and rigid polyurethane is used.
WHEEL ARCH MOLDING
13EOSX-30E a Wheel arch moldings are fitted to the front and rear fenders to give the vehicle an aggressive look.

S
FRONT BUMPER FRONT BUMPER
COMPONENTS
Rem’ovat ! Installation
1. Removal in the order shown
2. Install in the reverse order of
1 in the figure.
removal.
-9-9.8 Nm 170-100 kgfem,
U-87 h.lbfJ
f4-m Ikgf-m, ft-lbf J
13EOSX-312
4. Front bumper
Disassembly / Assembly
. . . . . . . . . ..m... page S-9 1. Radiator grille
2. Front conbination light
3. Headlight
5-8
Disassembh
I . Disassemi
2. Assemble
t
1. Fog lights
-
a
-I. 2. Bumper rear
3. Bumper me

FRONT BUMPER S
Disassembly / Assembly
I. Disassemble in the order shown in the figure.
2. Assemble in the reverse order of disassembly.
i
1, Fog lights
2. Bumper reinforcement
3. Bumper mesh 4. Hook cover
5. Bumper fascia

WHEEL ARCH MOLDING
Installation
Note
S
Front wheel arch molding
1. Remove the original adhesive from the molding mounting
surface of the body.
Caution
l Do not damage the surrounding painted area.
Note
l If the adhesive is difficult to remove, soften it by
using a hot air blower.
I URETHAtiE ADHESIVE
I
13EOSX-320
13EOSX-321
2. Clean and degrease the molding mounting surface of the
body and the bonding area of the molding.
3. Apply primer to the bonding area of the molding and allow
it to dry for approximately 30 minutes.
Caution
l Keep the area free of dirt, moisture, and grease.
l Do not touch the primed surfaces.
4. Apply urethane adhesive to the bonding area of the molding.
Caution
l The application range of urethane adhesive at each
point should be approximately 5 mm [ 0.2 in 1 wide
and 60 mm [ 2.4 in 1 long. Do not apply excessive
adhesive.
5. Align the molding to the body with the pin and clips, and
then install it.
6. Lightly press on the molding to obtain good adherence.
1
i
1
S-f 3 I

S WHEEL ARCH MOLDING
13EOSX-323
r
ADHESIVE TAPE
mm fin]
f 3EOSX-324
13EOSX.325
s-14.
Rear wheel arch molding
1. Remove the original adhesive from the molding mounting
surface of the body.
Caution
l Do not damage the surrounding painted area.
Note
l tf the adhesive is difficult to remove, soften it by
using a hot air blower.
2. Clean and degrease the molding mounting surface of the
body and the bonding area of the molding.
3. Apply primer to the bonding area of the molding and allow
it to dry for approximately 30 minutes.
Caution
l Keep the area free of dirt, moisture, and grease.
l Do not touch the primed surfaces.
4. Apply strips of double-coated adhesive tape to the bond-
ing area of the molding.
Note
l Use 40 mm I-1.6 in) lengths of tape.
5. Apply urethane adhesive to the bonding area of the molding.
Caution
l The application range of urethane adhesive should
be approximately 5 mm f 0.2 iii ) wide and 60 mm
(2.4 in) long. Do not apply excessive adhesive.
6. Peel the protection paper from the double-coated adhesive
tape.
7. Align the molding to the body with the pin, and then install it,
8. Lightly press on the molding to obtain good adherence.
9. tnstall the fasteners.

T
BODY ELECTRICAL SYSTEM
INDEX .*,........,..............*....*...*.........*....*.*.
T- 2
jFEATURESl
OUTLINE . . . . . . ..*.....*..*...~.=.........*.*........*~...~
T- 3
FEATURES .e . . . . . *..* . . . . . . * . . . . . . * . . . . . . . *..I . . . . . . . . .
T- 3
LIGHTING SYSTEM .,....*.*..m...*..,...,a*..*.*..,..
T- 3
SPECIFICATDNS .I..*.*...*....*....*.............,.
T- 3
SUPPLEMENTAL SERVICE
INFORMATlON I . . . . . . . . . . . . . . . . . *.*.a=..* . . . . . . . *..*.s
T- ,4
EXTERlOR LlGHTlNG SYSTEM . . . . .
l . . ..e.am..a.. T-
4
FRONT FOG LIGHT
. . . . . . n .* . . . . . l ...* . . . . . s* .,..I..
T- 4
f3EOTX-301
H .

T INDEX
NDEX
1 SEOTX-302
1. Front fog light
Removal I lnstallatron . . . . .._. . . . . . . _._. page T-4
OUTLINE
FEATURES
/Toimprov
jToimprov
t
SPECiFICi
1 Front fOQ II!
T-i