1992 MAZDA 323 fuel pump

SCHEDULED MAINTENANCE SERVICES A
SCHEDULED MAINTENANCE SERVICES
MAINTENANCE TABLE
Chafi symbols:
1 : Inspect: Visual examination and/or functional measurement of system’s operation or
performance , A: Adjust: Examination resulting in adjustment or replacement
n
R: Replace or change
T: Tighten
REMARKS
After 80,000 km or 48 months, continue to follow the described maintenance at the recommended intervals.
As for * marked items in this maintenance chart, note the following points.
+ 1 Major service interval at 12 months/20,000 km (12,000 miles).
Lubrication service based on distance only 10,000 km (6,000 miles) not time.
l 2 Adjust or inspect alternator and water pump drive belt, and power steering and air conditioner drive belt
if equipped.
‘3 Replacement of the timing belt is required at every 100,000 km (60,000 mile). Failure to replace the tim-
ing bett may result in damage to the engine.
‘4 tf the vehicle is operated under any of the following conditions, it is suggested that the engine oil and
oil filter be changed more often than the recommended intervals.
a) Driving in dusty conditions. I
:
b) Extended periods of idling or low speed operation. i
i!
c) Driving for a prolonged periods in cold temperatures or regularly driving onty short distances.
*5 If the vehicle is operated in very dusty or sandy areas, inspect and, if necessary, replace more often
than at usual recommended intervals.
l 6 This IS a full function check of all electrical systems, i.e, atl
ltghts. washers (including condition of blades)
electric windows, sunroof, horn etc.
‘7 Replace every two years. $1
‘I
If there has been continuous hard driving, mountain
drivtng, or if the brakes are used extensively or the
vehicle is operated in extremely humid climates, the brake fluid should be changed annually.
Emission Control and Related Systems
The ignition and fuel systems are vitally important to the proper operation of the-emission control and relat-
ed system, as well as for efficient engine operation. It is strongly recommended that all servicing related
to these systems be done by your Authorised Mazda Dealer.
13EOAX-302 -4
I!
A-3

F3
c
FUEL AND EMISSION
CONTROL
SYSTEMS
i
INDEX . . . . . . . . l ..,.... *..,. . . . . . . m...*.*...*..... F3- 2
UUTLtNE
...................................... F3- 4
OUTLINE OF CONSTRUCTION.. ....
F3- 4
SYSTEM DIAGRAM ...................... F3- 5
VACUUM HOSE ROUTING
DIAGRAM
................................. F3- 6
WIRING DIAGRAM.. .....................
F3- 7
ECU RELATIONSHIP DIAGRAM ...... F3- 8
SPECIFICATIONS.. ....................... F3- 9
TURBOCHARGER CONTROL .......... F3-IO
OUTLINE
.................................... F3-10
SYSTEM DIAGRAM ...................... F3-10
WASTEGATE CONTROL ............... F3-11
FUEL SYSTEM
.............................. F3-12
OUTLINE ....................................
F3-12
CONTROL SYSTEM .......................
F3-13
STRUCTURAL VIEW .....................
F3-13
PRESSURE REGULATOR
CONTROL SYSTEM ....................
F3-14 SUPPLEMENTAL SERVICE
tNFOF?MATtON
............................. F3-I 5
SELF-DtAGNOStS FUNCTtON.. ........
F3-16
OUTLINE ....................................
F3-16
SERVICE CODE NUMBERS..
......... F3-16
TROU8LESHOOTtNG GUtDE
........... F3-19
RELATIONSHtP
CHART.. F3-19 ..............
DIAGNOSTIC JNDEX
.................... F3-20
PRECAUTIONS
............................
F3-21
SYMPTOM TROUBLESHOOTING .... F3-22
TURBOCHARGERCONTROL
SYSTEM ......................................
F3-37
TURBOCHARGER F3-37 ........................
WASTEGATE SOLENOID VALVE.. .. F3-38
INTERCOOLER ............................
F3-39
FUELSYSTEM ..............................
F3-40
FUEL PUMP ................................
F3-40
FUEL PUMP RESISTOR/RELAY ......
F3-40
PRESSURE
REGULATOR .............. F3-41
INJECTOR ..................................
F3-42
INJECTOR RESISTOR
................... F3-42
PRESSUR REGULATOR CONTROL
SYSTEM ......................................
F3-43
SOLENOID VALVE (PRESSURE
REGULATOR CONTROL)
............. F3-43
CONTROL SYSTEM
....................... F3-44
PREPARATION ............................ F3-44
ENGINE CONTROL UNIT (ECU) ..... F3-45
7 3EOF3-301

INDEX F3
t
3EOf3.303
1. Injector 4. Solenoid valve (PRC high temp.)
Inspection ................................. page F3-42 Inspection ;. ............................... page F3-43
Volume test.; ............................. page F3-42 5. Fuel pump resistor/relay
2. Pressure regulator System operation ...................... page F3-40
Inspection ................................. page F3-4 1 Inspection ....... . .........................
page F3-4 1
II
3. Solenoid valve (PRC low temp.) 6. Fuel pump (main)
Inspection ................................. page F3-43 Inspection .......... . ...................... page F3-40

F3 OUTLINE
OUTLINE
OUTLINE OF CONSTRUCTION
Theefuel and emission control system of the new 323 4WD model 1s basically the same as that of the prevr-
ous 323 4WD model; however some parts are changed. The changed parts and interchangable parts
are shown betow.
13EOF3-304
Changed parts
1 ~ components Contents and purpose Reference pagl
INTAKE AlR
SYSTEM Turbocharger
Intercooler
l Size Increased for greater boost pressure l Wastegate solenord valve IS lozated on Intake port of F3-10
turbocharger to make system more compact F3-37
Volume increased for Improved F3-10
t F3-39
Wastegate sojenold valve
l Wastegate solenoid valve changed to duty solenoid
type for Increased engine power and response
l Wastegate solenoid valve is located on Intake port of
turbocharger to make system more compact F3-1 f
F3-38
I r
Pressure regulator One-stage operattlon changed to two-stage operatron F3-14
to improve hot restarting f3-41
L
FUEL SYSTEM High-ohmic type change to low-ohmrc type with exter-
Fuel qector na solenoid reslstor for improved fuel supply during F3-12
high-speed driving F3-42
Fuel pump reslstor Resistance reduced for
surer fuel supply F3-40
CONTROL
SYSTEM Pressure
regulator control system
Atr flow meter Two-stage operatton used to Improve hot restarting
Measures larger amount of air flow Increased power
Resistance values changed F3-t4
F3-43
F3- 9
f3EOF3-305 lnterchangable parts
tntake air system
l
Air valve
l Air bypass valve
l Air cleaner
l Air cleaner element
Fuel system
l Fuel filter assembly
l Fuel pu.mp (transfer
l Fuel vapor valve Control system
. l Throttle sensor
l Water thermosensor
l Knock sensor and control unit
l Oxygen sensor
l Fuel pump control unit
l Main relay
l Circuit opening relay
l Check valve (two-way) .
Evaporative system
l Charcoal canister
l Check valve (two-way)
13EOF3-306
F3-4

CHECK VALVE SOLENOID VALVE
(PURGE CONTROL)
llll
*
SOLENOID VALVE
(PRC LOW TEMP.)
3 ~NTERCOOLERII’ I ,‘/ I
II II
’ f frrmvmlHHt-----lHt I -1 II II
IIt - --M:l, i -KNmK~[I~ ,
’ ISC VALVE
VALVE WATER CHAkCOAL
CANISTOR
CHECK VALVE
I FUEL FUEL FILTER
PUMP
I FUEL FILTER
TRANSFER
PUMP
AIRkLOW METER
(WITH INTAKE AIR THERMOSENSOR)
DISTRIBUTOR
CATALYTIC CONVERTER
l TO ENGINE CONTROL UNIT

F3 OIJTUNE
SPE
* TEN
The @
ECU RELATtONSHtP DtAGRAM
1NPUT DEVICE
KNOCK SENSOR
c AIRFLOW METER
KNOCK
DlSTRlBUTOR
91c YfTC”
THERMOSENSOR
OXYGENSENSOR N EUTRAti
CLUTCH SWITCH
CONNECTOR
(TEN TERMINAL,)
INTAKE AIR
OUTPUT
DEVtCE THERMOSENSOR
{AIRFLOW METER)
CIRCUIT
OPENING
TURBOCHARGE
jAGNOSE
ONNECTOR
EN/MEN TERMINA
h SOLENOID VALVE
(PRESSURE REGUL+TOR
CONTROL)
WASTEGATE
SOLENOID VALVE IGNITER
- - (TURBtiHARGER)
FUEL PUMP
RESlSTORlRELAY
SOLENOID VALVE
(PURGE CONTROL)
F3-8 13EOF3-311

OUTLINE F3
SPEClFiCATlONS
Iten
Idle speed’
tgnltion trming * Engine
m
BTDC BP TURBO
800 f 50
IO f 10
Fuel pump
Maximum output pressure kPa { kgflcm’, psi 1 1 490-736 {SO-7.5, 7t-110)
Transfer pump
Maximum output pressure
Fuel filter kPa { kgf/cm2, psi ) 1 , 39 10.4, 5.7 1 or higher
Nylon element (in fuel pump)
Idle-speed control (fSC) valve
Type
Resistance I Rotary
nt
11-13 [at 2O*C [68*F)]
Solenoid va tve (purge contra I)
,I
Resistance -2o*c I -4Of 1 14.6-I 7.8
2.21-2.69
.kQ , 2o”c { 68OF)
40% f104*f 1 1.0-l .3
Resistance
Fuel tank
Capacity
Air cleaner
Etement type
Fuel
Specification L {US gal, Imp gal) [ Approx. 6 [at 20°C f 68*FJ]
60 (15.9, 13.2)
01 permeated
Unleaded premium (RON 95 or higher)
11FrlC?.7 11
l TEN terminal of diagnosis connector grounded.
The I; mark indicates newly equipped Parts. l”L”l “VI I
F3-9

SUPPLEMENTAL SERVICE INFORMATION .
I
The following points in this section are changed in comparison to the Mazda 323 4-Wheel Drive Work-
shop Manual [I 229-l O-89t].
Turbocharger
l Removal / Installation
Wastegate solenoid valve
l Inspection
htercooter
l Removal I Installation
Fuel pump (main)
l Inspection
Fuel pump resistor/relay
l System operation
l Inspection
Injector
l Inspection
l Volume test
Injector resistor
l Inspection
Pressure regulator control system
l Solenoid valve (pressure regulator control}
Engine control unit (ECU)
l Inspection 13EOF3.320
F3-I 5