Page 18 of 20

COMFORT ADJUSTMENT
60CAUTION:
After installation, make sure the child restraint system is
secured in place. If the child restraint system is not
restrained securely, it may cause injury to the child in the
event of sudden stop or accident.
When not using the child restraint system, keep it secured with
the seat belt or remove it and place it in the trunk or somewhere
other than in the vehicle to prevent injury to passengers in the
event of a sudden stop or accident.
INSTALLATION ON REAR SEAT CENTER
Top strap
Anchor bracket
1. Fasten the center lap belt over the child restraint system.
2. Tighten the lap belt.
If your child restraint system requires the use of a top strap,
latch the hook onto the anchor bracket and tighten the top
strap.
INSTALLATION ON REAR SEAT OUTSIDE
Top strap
Anchor bracket
1. Fasten the lap and shoulder belt over the child restraint
system
2. Keep slack out of the lap portion of the belt.
3. Holding the tab in that position, release the buckle.
4. Install a locking clip near the tab of the lap and shoulder belt.
(See instructions in the next page.)
5. Buckle the belt again.
6. Place the shoulder portion of the belt between the vehicle
seatback and the child restraint system.
Page 19 of 20

COMFORT ADJUSTMENT
61
Locking clip
To install the locking clip, thread the lap and shoulder webbing
through the recesses of the locking clip.
Always remove the locking clip when the child restraint system
is not installed.
If your child restaint system requires the use of top strap, latch
the hook onto the anchor bracket and tighten the top strap.Top strap anchors and locations − On the filler panel behind
the rear seat
Anchor bracketBolt
Spacer
144 (5.7)200 (7.9)
62 (2.4)
62 (2.4)
200 (7.9)144 (5.7)
mm (in.)
a. Using the illustration as a guide, run your fingers across the
trim of the filler panel to locate the position of holes underneath.
b. Make a hole in the covering directly above the hole in the
filler panel.
c. Insert a 15 mm (0.6 in.) spacer for either outside anchor or
a 10 mm (0.4 in.) spacer for the center anchor, and tighten
down the anchor bracket for your child restraint system with a
bolt. Torque the bolt to 16.5 − 24.7 N
.m (1.68 − 2.52 kgf-m, 12.2
− 18.2 ft-Ib).
Page 20 of 20

COMFORT ADJUSTMENT
62To comply with Canada Motor Vehicle Safety Standards,
vehicles sold in Canada are provided with a bracket set in the
glovebox, designed for use with the center location shown in
the illustration. If you want to install the bracket set on either
outside anchor, replace the spacer (Part No. 90560-08064)
with one that is 15 mm (0.6 in.) thick. This can be purchased
from your Lexus dealer.
INSTALLATION ON FRONT SEAT
Locking clip
1. Fasten the lap and shoulder belt over the child restraint
system.
2. Keep slack out of the lap portion of the belt.
3. Holding the tab in that position, release the buckle.
4. Install a locking clip near the tab of the lap and shoulder belt.
(See instructions in the next column.)
5. Buckle the belt again. If necessary, slide the seat forward
and remove any slack.
6. Place the shoulder portion of the belt between the vehicle
seatback and the child restraint system.
Locking clip
To install the locking clip, thread the lap and shoulder webbing
through the recesses of the locking clip.
Always remove the locking clip when the child restraint system
is not installed.
Top strap
If your child restraint system requires the use of a top strap,
latch the hook onto the tab of the rear center seat belt and
tighten the top strap.