1991 MITSUBISHI MONTERO cooling

NOTE: Idle mixture is computer controlled on fuel injected engines
and is nonadjustable. CO level specifications are not
available from manufacturer.
THROTTLE POSITION SENSOR (TPS)
TPS ADJUSTMENT
NOTE: Ensure basic idle speed is set to specification before
adjusting TPS. See BASIC IDLE SPEED under IDLE SPEED &
MIXTURE. Perform all adjustments with engine at normal
operating temperature, front wheels in straight-ahead
position, cooling fan and all accessories off, and
transmission in Park or Neutral.
TPS TEST APPLICATION









\









\









\









\









Application Test
1.5L
Colt, Colt 200,
Mirage & Summit ............. TEST NO. 1
1.6L
Mirage ....................... TEST NO. 2
1.8L
Eclipse ...................... TEST NO. 3
2.0L (VIN V)
Colt Vista & Galant .......... TEST NO. 1
2.0L (VIN R & U)
Galant ....................... TEST NO. 1
Eclipse ...................... TEST NO. 3
2.4L
Pickup & Ram-50 .............. TEST NO. 1
3.0L
Montero, Pickup & Ram-50 ..... TEST NO. 4
Stealth & 3000GT ............. TEST NO. 5









\









\









\









\









Test No. 1
1) Turn ignition on for more than 15 seconds. DO NOT start
engine. Turn ignition off. ISC plunger should be retracted fully.
2) Ensure ISC plunger is in fully retracted position.
Disconnect harness connector(s) from ISC motor. Turn ignition on. DO
NOT start engine.
3) Using digital voltmeter, backprobe terminal No. 19
(Green/White wire) and terminal No. 24 (Black or Green/Black wire) a\
t
Engine Control Unit (ECU) wiring harness connector. Note TPS output
voltage.
4) If output voltage is .48-.52 volt, go to step 6). If
output voltage is not .48-.52 volt, loosen TPS mounting screw(s) and
rotate TPS clockwise, or counterclockwise, until output voltage is
within specification. Tighten TPS mounting screws.
5) Turn ignition off. Reconnect harness connector(s) at ISC
motor. Start engine. Ensure engine idles within curb idle speed
specification.
6) Turn ignition off. Disconnect negative battery cable for
at least 15 seconds to clear diagnostic trouble code. Reconnect
negative battery cable. Operate engine at idle for about 5 minutes to
ensure engine idles smoothly.
Test No. 2
1) Turn ignition on. DO NOT start engine. Loosen throttle

same axle to eliminate uneven braking behavior. Always wash drums
after servicing or before installing.
DRUM INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Balance weight missing .. .. ........ No service suggested or
required.
Bell-mouthed, affecting
performance ............ A ....... Require reconditioning or
replacement.
Cooling fin broken ...... .. ........ No service suggested or
required.
Cracked ................. B ............ Require replacement.
Drum diameter is greater
than OEM "machine to"
specifications but less
than "discard at"
specifications, and the
drum does not require
reconditioning ......... 1 ........ (1) Suggest replacement.
Drum diameter will exceed
OEM "machine to"
specifications after
required
reconditioning ......... B ........ ( 2) Require replacement.
Hard-spotted ............ 2 ....... Suggest reconditioning or
replacement.
Measured diameter is
greater than OEM discard
specifications ......... B ............ Require replacement.
Out-of-round (runout),
affecting performance .. A ....... Require reconditioning or
replacement.
Out-of-round (runout),
exceeding manufacturer's
specifications ......... B ....... Require reconditioning or
replacement.
Scored .................. B ....... Require reconditioning or
replacement.
Surface threaded due to
improper machining ..... B ....... Require reconditioning or
replacement.
Tapered, affecting
performance ............ A ....... Require reconditioning or
replacement.
( 1) - Only applies to vehicles for which OEM "machine to"
specifications exist. If OEM does not supply "machine to"
specifications, the drum may be worn to discard
specifications.
( 2) - If OEM does not supply "machine to" specifications, you
may machine to discard specifications.









\









\









\









\









\









\









\


ELECTRICAL PUMPS AND MOTORS
Copied fuel pump conditions from engine UIGs & deleted
pulsator from leaking conditions.
ELECTRICAL PUMP AND MOTOR INSPECTION









\









\









\









\









\









\









\

reconditioning ......... B ........ (3) Require replacement.
Surface is rust-pitted .. B ....... Require reconditioning or
replacement of rotor according
to OEM specifications.
Surface is scored ....... B ... ( 4) Require reconditioning or
replacement of rotor according
to OEM specifications.
Thickness variation
(parallelism) exceeds OEM
specifications .......... B ....... Require reconditioning or
replacement of rotor according
to OEM specifications.
( 1) - Examples of severe corrosion are: composite plate
separated from friction surfaces and cooling fins
cracked or missing.
( 2) - Only applies to vehicles for which OEM "machine to"
specifications exist. If OEM does not supply "machine
to" specifications, the rotor may be worn to discard
specifications.
( 3) - If OEM does not supply "machine to" specifications,
you may machine to discard specifications.
( 4) - Scoring is defined as grooves or ridges in the friction
contact surface. Some vehicle manufacturers require
machining when scoring exceeds their allowable
specifications.









\









\









\









\









\









\









\


SELF-ADJUSTING SYSTEMS
SELF-ADJUSTING SYSTEM INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Bent .................... A ... Require repair or replacement
of bent part.
Broken .................. A ... Require repair or replacement
of broken part.
Inoperative ............. A ........... ( 1) Require repair or
replacement of inoperative
parts.
Missing ................. C .......... Require replacement of
missing part.
Star wheel does not turn
freely ................. A .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation.









\









\









\









\









\









\









\


SHOE HARDWARE
See BRAKE SHOE HARDWARE .
SHOES
See FRICTION MATERIAL .
SOCKETS
See BULB SOCKETS.
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)

CO M PU TE R R ELE A R N P R O CED URES

1991 M it s u bis h i M onte ro
GENERAL INFORMATION
Computer Relearn Procedures
All Models
* PLEASE READ THIS FIRST *
The following general procedures are to be used if
driveability problems are encountered after power loss or battery has
been disconnected. These procedures may provide an aid in eliminating
these problems.
To reduce the possibility of complaints, after any service
which requires battery power to be disconnected, vehicle should be
road tested.
COMPUTER RELEARN PROCEDURES
Vehicles equipped with engine or transmission computers may
require a relearn procedure after vehicle battery is disconnected.
Many vehicle computers memorize and store vehicle operation patterns
for optimum driveability and performance. When vehicle battery is
disconnected, this memory is lost. The computer will use default data
until new data from each key start is stored. As computer memorizes
vehicle operation for each new key start, driveability is restored.
Vehicle computers may memorize vehicles operation patterns for 40 of
more key starts.
Customers often complain of driveability problems during
relearn stage because vehicle acts differently then before being
serviced. Depending on type and make of vehicle and how it is
equipped, the following complaints (driveability problems) may exist:
* Harsh Or Poor Shift Quality
* Rough Or Unstable Idle
* Hesitation Or Stumble
* Rich Or Lean Running
* Poor Fuel Mileage
These symptoms and complaints should disappear after a number
of drive cycles have been memorized. To reduce the possibility of
complaints, after any service which requires battery power to be
disconnected, vehicle should be road tested. If a specific relearn
procedure is not available, the following procedure may be used:
Automatic Transmission
* Set parking brake, start engine in "P" or "N" position.
Warm-up vehicle to normal operating temperature or until
cooling fan cycles.
* Allow vehicle to idle for one minute in "N" position. Select
"D" and allow engine to idle for one minute.
* Accelerate at normal throttle position (20-50%) until vehicle
shifts into top gear.
* Cruise at light to medium throttle.
* Decelerate to a stop, allowing vehicle to downshift, and use
brakes normally.
* Process may be repeated as necessary.
Manual Transmission

CO OLIN G S YSTE M S PEC IF IC ATIO NS

1991 M it s u bis h i M onte ro
1991 ENGINE COOLING
Mitsubishi Cooling System Specifications
Mitsubishi: Eclipse, Galant, Mirage,
Montero, Pickup, Precis, 3000GT
COOLING SYSTEM SPECIFICATIONS
COOLING SYSTEM SPECIFICATIONS TABLE








\









\









\









\









\









\









\







Application Specification
Coolant Replacement Interval ............. 30,000 Miles or 24 Months
Coolant Capacity
(Includes Heater & Reserve Tank)
Eclipse
1.8L .......................................... 6.6 qts. (6.2L)\
2.0L .......................................... 7.6 qts. (7.2L)\
Galant .......................................... 7.6 qts. (7.2L)\
Montero ........................................ 10.0 qts. (9.5L)\
Pickup
2WD
Automatic Transmission ....................... 6.4 qts. (6.1L)\
Manual Transmission .......................... 6.3 qts. (6.0L)\
4WD ........................................... 8.9 qts. (8.4L)\
Precis .......................................... 5.6 qts. (5.3L)\
3000GT .......................................... 8.8 qts. (8.3L)\
Pressure Cap ............................................. 11-15 psi
Thermostat Opens
Except 3000GT
Starts ............................................. 190
F (88C)
Fully Open ........................................ 212F (100C)
3000GT
Starts ............................................. 170
F (77C)
Fully Open ......................................... 190F (88C)








\









\









\









\









\









\









\

DRIV E B ELT R O UTIN G

1991 M it s u bis h i M onte ro
1991 ENGINE COOLING
Mitsubishi Drive Belt Routing
Mitsubishi; Eclipse, Galant, Mirage,
Montero, Pickup, Precis, 3000GT
BELT ADJUSTMENT SPECIFICATIONS
BELT ADJUSTMENT TABLE








\









\









\









\









\









\









\







Deflection
Application ( 1) In. (mm)
Eclipse
1.8L .......................................... .32-.43 (8.1-10.9)\
2.0L .......................................... .35-.45 (8.9-11.4)\
Galant ( 2)
Alternator Belt ............................... .35-.45 (8.9-11.4)\
A/C Belt ............................................... .32 (8.1)\
Power Steering Belt ............................ .24-.35 (6.1-8.9)\
Montero ( 3) ...................................... .20-.24 (5.1-6.1)
Pickup
2.4L ........................................... .27-.39 (6.8-9.9)\
3.0L ( 3) ....................................... .32-.39 (8.1-9.9)
Precis
A/C Belt ...................................... .32-.40 (8.1-10.2)\
Alternator Belt ................................ .28-.32 (7.1-8.1)\
3000GT ( 4)
DOHC
Alternator Belt ............................... .16-.22 (4.1-5.6)\
Power Steering Belt .......................... .35-.43 (8.9-10.9)\
SOHC
Alternator & Power Steering Belt .............. .24-.35 (6.1-8.9)\
A/C Belt ...................................... .28-.37 (7.1-9.5)\
( 1) - With 22 lbs. (10 kg) pressure applied midway on belt run.
( 2) - For belt routing, see Fig. 1.
( 3) - For belt routing, see Fig. 2.
( 4) - For belt routing, see Figs. 3, 3 or 4.









\









\









\









\









\









\









\

EN G IN E C O OLIN G F A N
1991 M it s u bis h i M onte ro
1991 ENGINE COOLING
Mitsubishi Engine Cooling Fans
Mitsubishi: Eclipse, Galant, Mirage,
Montero, Pickup, Precis, 3000GT
ELECTRIC COOLING FAN - COMPONENT TESTING
MOTOR
Disconnect electric cooling fan motor at junction. Using 2
jumper wires, ground one lead and apply battery voltage to other. Fan
should rotate. If fan does not rotate, replace motor.
RADIATOR FAN SWITCH
Using an ohmmeter, check switch continuity in hot water.
Switch should be open at less than 180F (82C) and continuity should
exist at more than 185F (85C). Replace radiator fan switch if it
does not test as specified.
ELECTRIC COOLING FAN RELAY
1) Remove relay from relay box in front of right suspension
tower. Using jumper wires, connect battery to indicated terminals.
2) On 3000GT, continuity should exist between terminals No. 1
and 3. With battery disconnected, continuity should exist between
terminals No. 2 and 4 and should not exist between terminals No. 1 and
3.
3) On all other models, continuity should exist between
terminals No. 3 and 4. With battery disconnected, continuity should
exist between terminals No. 1 and 2 and should not exist between
terminals No. 3 and 4. Replace relay if it does not test as specified.
Fig. 1: Testing Electric Cooling Fan Relay (except 3000GT)
Courtesy of Mitsubishi Motor Sales of America.

Fig. 2: Testing Electric Cooling Fan Relay (3000GT)
Courtesy of Mitsubishi Motor Sales of America.
ELECTRIC COOLING FAN - SYSTEM TESTING
MIRAGE 1.5L
1) With A/C on LOW position, ignition on and engine coolant
temperature greater than 185F (85C), thermosensor completes path to
ground, closing radiator fan motor relay contacts and providing
current to radiator fan motor. See Fig. 1.
2) With A/C on HIGH position and ignition on, power supply
from automatic compressor control unit causes condenser fan motor
relay and condenser fan motor control relay to turn on, causing
condenser fan and radiator cooling fan to operate.