1991 MITSUBISHI MONTERO engine oil

* Check motor position sensor (if applicable).
* Check fuel pressure.
* Check for disconnected or damaged vacuum hoses.
* Check for PFI system malfunction.
* Check for stepper motor malfunction (if applicable).
* Check for fuel injector malfunction.
* Check for power transistor malfunction.
* Check for A/C power relay control system malfunction (if
applicable).
* Check for ECU malfunction.
* Ensure electrical harness, connectors and wires are not
broken or loose.
ENGINE SURGES
* Check coolant temperature sensor.
* Check idle position switch.
* Check EGR control solenoid valve (if applicable).
* Check fuel pressure.
* Check for fuel injector malfunction.
DETONATION OR KNOCKING
* Check airflow sensor.
* Check for cooling system problems.
* Check fuel quality.
* Check intake air temperature sensor.
* Check barometric pressure sensor.
* Check ignition coil.
* Check power transistor.
* Check for EGR system malfunction.
POOR FUEL MILEAGE
* Check intake air temperature sensor.
* Check engine coolant temperature sensor.
* Check barometric pressure sensor.
* Check ignition switch.
* Check idle position switch.
* Check throttle position sensor.
* Check TDC sensor.
* Check crank angle sensor.
* Check power steering oil pressure switch.
* Check A/C switch (if applicable).
* Check inhibitor switch (A/T).
* Check oxygen sensor.
* Check airflow sensor.
* Check motor position sensor (if applicable).
* Check fuel pressure.
* Check for PFI system malfunction.
* Check for stepper motor malfunction.
* Check for fuel injector malfunction.
* Check for power transistor malfunction.
INTERMITTENTS
INTERMITTENT PROBLEM DIAGNOSIS
Intermittent fault testing requires duplicating circuit or
component failure to identify problem. These procedures may lead to
computer setting a fault code which may help in diagnosis.
If problem vehicle does not produce fault codes, monitor

input device usage on specific models, see appropriate wiring diagram
in M - WIRING DIAGRAMS.
Air Conditioner Switch
When A/C is turned on, signal is sent to ECU. With engine at
idle, ECU increases idle speed through Idle Speed Control (ISC) motor.\
Airflow Sensor
Incorporated in airflow sensor assembly, airflow sensor is a
Karmen Vortex-type sensor which measures intake airflow rate.
Intake air flows through tunnel in airflow sensor assembly.
Airflow sensor transmits radio frequency signals across direction of
incoming airflow, downstream of vortex. Intake air encounters vortex,
causing turbulence in tunnel.
Turbulence disrupts radio frequency, causing variations in
transmission. Airflow sensor converts frequency transmitted into a
proportionate electrical signal which is sent to ECU.
Airflow Sensor Assembly
Mounted inside air cleaner, incorporates airflow sensor,
atmospheric pressure sensor and intake air temperature sensor.
Atmospheric (Barometric) Pressure Sensor
Incorporated in the airflow sensor assembly, converts
atmospheric pressure to electrical signal which is sent to ECU. ECU
adjusts air/fuel ratio and ignition timing according to altitude.
Coolant Temperature Sensor
Converts coolant temperature to electrical signal for use by
ECU. ECU uses coolant temperature information for controlling fuel
enrichment when engine is cold.
Crankshaft Angle & TDC Sensor Assembly
Assembly is located in distributor on SOHC engines. On DOHC
engines, which use Direct (or Distributorless) Ignition System (DIS)\
,
assembly is separate unit mounted in place of distributor. Assembly
consists of triggering disc (mounted on shaft) and stationary optical
sensing unit. Camshaft drives shaft, triggering optical sensing unit.
ECU determines crank angle and TDC based on signals received from
optical sensing unit.
Detonation Sensor (Turbo Only)
Located in cylinder block, senses engine vibration during
detonation (knock). Sensor converts vibration into electrical signal.
ECU retards ignition timing based on this signal.
Engine Speed (Tach Signal)
ECU uses ignition coil tach signal to determine engine speed.
Idle Position Switch
On all DOHC engines and Sigma 3.0L, idle position switch is
separate switch mounted on throttle body. On all other models, idle
position switch is incorporated in ISC motor or throttle position
sensor, depending on vehicle application. When throttle valve is
closed, switch is activated. When throttle valve is at any other
position, switch is deactivated. This input from idle position switch
is used by ECU for controlling fuel delivery time during deceleration.
Ignition Timing Adjustment Terminal
Used for adjusting base ignition timing. When terminal is
grounded, ECU timing control function is by-passed, allowing base
timing to be adjusted.

Inhibitor Switch (Automatic Transmission Only)
Inhibitor switch senses position of transmission select
lever, indicating engine load due to automatic transmission
engagement. Based on this signal, ECU commands ISC motor to increase
throttle angle, maintaining optimum idle speed.
Intake Air Temperature Sensor
Incorporated in airflow sensor assembly, this resistor-based
sensor measures temperature of incoming air and supplies air density
information to ECU.
Motor Position Sensor (MPS)
Incorporated in ISC motor (or separate unit on some models),
senses ISC motor plunger position and sends electrical signal to ECU.
Oxygen (O2) Sensor
Located in exhaust system, generates an output voltage.
Output voltage varies with oxygen content of exhaust gas stream. ECU
adjusts air/fuel mixture based on signals from oxygen sensor.
Power Steering Oil Pressure Switch
Detects increase in power steering oil pressure. When power
steering oil pressure increases, switch contacts close, signalling
ECU. ECU commands ISC motor, raising idle speed to compensate for drop
in engine RPM due to power steering load.
TDC Sensor
See CRANKSHAFT ANGLE & TDC SENSOR ASSEMBLY.
Throttle Position Sensor (TPS)
A variable resistor mounted on throttle body. ECU uses
voltage signal received from TPS to determine throttle plate angle.
Vehicle Speed Sensor
Located in speedometer in instrument cluster, uses a reed
switch to sense speedometer gear revolutions. ECU uses gear
revolutions to determine vehicle speed.
OUTPUT SIGNALS
NOTE: Vehicles are equipped with different combinations of
computer-controlled components. Not all components listed
below are used on every vehicle. For theory and operation on
each output component, refer to the system indicated in
brackets after component.
CHECK ENGINE Light
See SELF DIAGNOSTIC SYSTEM.
EGR Control Solenoid Valve
See EXHAUST GAS RECIRCULATION (EGR) CONTROL under EMISSION
SYSTEMS.
Fuel Injectors
See FUEL CONTROL under FUEL SYSTEM.
Fuel Pressure Control Solenoid Valve (Turbo Only)
See FUEL DELIVERY under FUEL SYSTEM.
Fuel Pressure Regulator
See FUEL DELIVERY under FUEL SYSTEM.
Fuel Pump Relay (MPI Control Relay)

See FUEL DELIVERY under FUEL SYSTEM.
Idle Speed Control Servo
See IDLE SPEED under FUEL SYSTEM.
Power Transistor(s) & Ignition Coils
See IGNITION SYSTEMS.
Purge Control Solenoid Valve
See EVAPORATIVE CONTROL under EMISSION SYSTEMS.
Self-Diagnostic Connector
See SELF-DIAGNOSTIC SYSTEM.
Wastegate Control Solenoid Valve
See TURBOCHARGED ENGINES under AIR INDUCTION SYSTEM.
FUEL SYSTEM
FUEL DELIVERY
Electric fuel pump (located in gas tank) feeds fuel through
in-tank fuel filter, external fuel filter (located in engine
compartment) and fuel injector rail.
Fuel Pump
Consists of an impeller driven by a motor. Pump has an
internal check valve to maintain system pressure and a relief valve to
protect the fuel pressure circuit. Pump receives voltage supply from
Multi-Point Injection (MPI) control relay.
Fuel Pressure Control Solenoid Valve (Turbo Only)
Prevents rough idle due to fuel percolation. On engine
restart, if engine coolant or intake air temperatures reach a preset
value, ECU applies voltage to fuel pressure control solenoid valve for
2 minutes after engine re-start. Valve opens, allowing atmospheric
pressure to be applied to fuel pressure regulator diaphragm. This
allows maximum available fuel pressure at injectors, enriching fuel
mixture and maintaining stable idle at high engine temperatures.
Fuel Pressure Regulator
Located on fuel injector rail, this diaphragm-operated relief
valve adjusts fuel pressure according to engine manifold vacuum.
As engine manifold vacuum increases (closed throttle), fuel
pressure regulator diaphragm opens relief valve, allowing pressure to
bleed off through fuel return line, reducing fuel pressure.
As engine manifold vacuum decreases (open throttle), fuel
pressure regulator diaphragm closes valve, preventing pressure from
bleeding off through fuel return line, increasing fuel pressure.
FUEL CONTROL
Fuel Injectors
Fuel is supplied to engine through electronically pulsed
(timed) injector valves located on fuel rail(s). ECU controls amount\
of fuel metered through injectors based upon information received from
sensors.
IDLE SPEED
Air Conditioner Relay
When A/C is turned on with engine at idle, ECU signals ISC

motor to increase idle speed. To prevent A/C compressor from switching
on before idle speed has increased, ECU momentarily opens A/C relay
circuit.
Idle Speed Control (ISC) Motor
Controls pintle-type air valve (DOHC engines) or throttle
plate angle (SOHC engines) to regulate volume of intake air at idle.
During start mode, ECU controls idle intake air volume
according to coolant temperature input. After starting, with idle
position switch activated (throttle closed), fast idle speed is
controlled by ISC motor and fast idle air control valve (if equipped).\
When idle switch is deactivated (throttle open), ISC motor
moves to a preset position in accordance with coolant temperature
input.
When automatic transmission (if equipped) is shifted from
Neutral to Drive, A/C is turned on or power steering pressure reaches
a preset value, ECU signals ISC motor to increase engine RPM.
Fast Idle Air Control Valve
Some models use a coolant temperature-sensitive fast idle air
control valve, located on throttle body, to admit additional intake
air volume during engine warm-up. Control valve closes as temperature
increases, restricting by-pass airflow rate. At engine warm-up, valve
closes completely.
IGNITION SYSTEMS
DIRECT IGNITION SYSTEM (DIS) - DOHC ENGINES
Ignition system is a 2-coil, distributorless ignition system.
Crankshaft angle and TDC sensor assembly, mounted in place of
distributor, are optically controlled.
Power Transistors & Ignition Coils
Based on crankshaft angle and TDC sensor inputs, ECU controls
timing and directly activates each power transistor to fire coils.
Power transistor "A" controls primary current of ignition coil "A" to
fire spark plugs on cylinders No. 1 and 4 at the same time. Power
transistor "B" controls primary current of ignition coil "B" to fire
spark plugs on cylinders No. 2 and 3 at the same time.
Although each coil fires 2 plugs at the same time, ignition
takes place in only one cylinder since the other cylinder is on its
exhaust stroke when plug fires.
ELECTRONIC IGNITION SYSTEM - SOHC ENGINES
Mitsubishi breakerless electronic ignition system uses a disc
and optical sensing unit to trigger power transistor.
Power Transistor & Ignition Coil
Power transistor is mounted inside distributor with disc and
optical sensing unit. When ignition is on, ignition coil primary
circuit is energized. As distributor shaft rotates, disc rotates,
triggering optical sensing unit. ECU receives signals from optical
sensing unit. Signals are converted and sent to power transistor,
interrupting primary current flow and inducing secondary voltage.
IGNITION TIMING CONTROL SYSTEM
Ignition timing is controlled by ECU. ECU adjusts timing
based upon various conditions, such as engine temperature, altitude
and detonation (turbo vehicles only).

system consists of PCV valve, oil separator, breather and ventilation
hoses.
PCV valve is a one-way check valve, located in valve cover.
When engine is running, manifold vacuum pulls PCV valve open, allowing
crankcase fumes to enter intake manifold. If engine backfires through
intake manifold, PCV valve closes to prevent crankcase combustion.
SELF-DIAGNOSTIC SYSTEM
Self-diagnostic system monitors input and output signals. On
all models, codes can be read using analog voltmeter. On some models,
scan tool can be used to read codes. For additional information, see G
- TESTS W/ CODES article.
CHECK ENGINE Light
Also called Malfunction Indicator Light by manufacturer,
comes on when ignition is turned on. Light remains on for several
seconds after engine has started. If an abnormal input signal occurs,
light comes on and code is stored in memory. If an abnormal input
signal returns to normal, ECU turns light off but code remains stored
in memory until cleared. If ignition is turned on again, light will
not come on until ECU detects malfunction during system operation.
NOTE: ECU diagnostic memory is retained by direct power supply
from the battery. Memory is not erased by turning off
ignition but is erased if battery or ECU is disconnected.

\003
TR AN SM IS SIO N R EM OVA L & IN STA LLA TIO N - A /T
1991 M it s u bis h i M onte ro
199192 TRANSMISSION SERVICING
Transmission Removal & Installation
Mitsubishi: Eclipse, Galant, Mirage, Montero,
Pickup, Precis, 3000GT
MANUAL
NOTE: For manual transmission/transaxle replacement procedures,
see appropriate article in CLUTCHES.
AUTOMATIC FWD MODELS
REMOVAL
1) Remove battery and battery tray. On 3000GT, remove
undercover(s). On Eclipse turbo, drain and remove intercooler. On all
models, remove air cleaner and case. Raise and support vehicle. Remove
wheels. Disconnect control cables at transaxle. Drain transaxle fluid.
2) On Mirage 1.6L, disconnect tension rod. On all models,
disconnect neutral safety switch connector, oil cooler hoses and
electrical connectors from transaxle. Disconnect speedometer cable and
throttle control cable (if equipped). Remove starter motor.
3) On Galant models with electronically controlled
suspension, remove air compressor and bracket. Disconnect front height
sensor rod at lower control arm.
4) On all models, remove upper transaxle-to-engine bolts.
Remove engine undercover (if equipped). On all models, remove drive
axle shafts. See FWD AXLE SHAFTS article in DRIVE AXLES. Separate
lower control arms from struts for access to axle shafts (if
necessary).
5) Remove front exhaust pipe (if necessary). On Eclipse 4WD,\
Galant 4WD and 3000GT, remove right member and gusset. On 4WD models,
separate transfer assembly from transaxle. Reference mark transfer
assembly-to-drive shaft and remove transfer assembly.
6) On all models, remove transmission inspection (dust)
cover. Place index mark on torque converter and drive plate for
reassembly reference. Remove torque converter-to-drive plate bolts.
Push torque converter away from engine into transaxle.
7) Support transaxle with jack. Remove transaxle mounts
bolts, mounting brackets and remaining transaxle-to-engine bolts.
Slide transaxle assembly to right and lower to remove.
CAUTION: Ensure torque converter is fully seated in transaxle before
installation. Always install new snap rings on inner
constant velocity joints.
INSTALLATION
1) To install, reverse removal procedure. Tighten transaxle-
to-engine bolts and torque converter-to-drive plate bolts to
specification. See TORQUE SPECIFICATIONS table at end of article.
2) Ensure reference marks on torque converter-to-drive plate
and transfer assembly-to-drive shaft align. Tighten mounting bolts
with weight of engine and transaxle on mounts. Refill transaxle fluid
to specified level. Adjust all control cables.
RWD MODELS

REMOVAL
1) Disconnect negative battery cable. Remove front exhaust
pipe. On Montero, remove transfer case shift lever knob, dust boot and
retainer plate or console. Remove transfer case gearshift assembly.
2) On all models, raise and support vehicle. Remove
undercarriage cover and/or skid plate(s). Drain transmission and
transfer case (if applicable). Place reference mark on drive shaft(s)\
and remove. Disconnect all external solenoid and switch connections.
3) Disconnect speedometer cable and control cables at
transmission. Remove starter and bellhousing cover. Place reference
mark on torque converter and drive plate for reassembly reference.
Remove torque converter bolts.
4) Disconnect transmission cooler lines. Remove oil filler
tube. Secure transmission on a jack. Raise transmission slightly to
take weight off mount. Remove crossmember-to-mount bolts and
crossmember.
5) Remove transfer case mounting bracket and mount (if
equipped). Remove transmission-to-engine mounting bolts. Carefully
lower transmission from vehicle.
CAUTION: Ensure torque converter is fully seated in transmission
before installation.
INSTALLATION
1) To install, reverse removal procedure. Tighten
transmission-to-engine bolts and torque converter-to-drive plate bolts
to specification. See TORQUE SPECIFICATIONS table at end of article.
Tighten mount bolts with weight of engine and transmission on mounts.
Ensure reference marks on drive shaft(s) and torque converter-to-drive\
plate align.
2) Apply sealant to transfer case gearshift assembly gasket
before installation. Coat transmission oil filler tube "O" ring with
transmission fluid before installation. Refill transmission fluid to
specified level. Adjust all control cables.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS








\









\









\









\









\









\









\


Applications Ft. Lbs. (N.m)
FWD Models
Torque Converter-To-Drive Plate Bolt
Precis ....................................... 53-55 (72-76)
All Others ................................... 34-38 (46-52)
Transaxle-To-Engine Block Bolt
Mirage
8-mm Bolt ............................................ (1)
10-mm Bolt ................................. 22-25 (30-34)
12-mm Bolt ................................. 31-40 (42-54)
Eclipse & Galant
8-mm Bolt ............................................ (1)
10-mm Bolt ................................. 22-25 (30-34)
Precis
8-mm Bolt .................................. 22-25 (30-34)
10-mm Bolt ................................. 31-40 (42-54)
3000GT
Upper Coupling Bolts ............................. 54 (73)
Lower Coupling Bolts ............................. 65 (88)