1991 MITSUBISHI MONTERO engine coolant
[x] Cancel search: engine coolantPage 692 of 1333
Courtesy of Mitsubishi Motor Sales of America.
2) Disconnect air intake hose and vacuum hoses. Remove air
hose and air outlet housing. Remove heat protectors. Disconnect
exhaust pipe. Remove power steering oil pump and bracket. Remove
engine hanger bracket. Disconnect oil inlet pipe.
3) Disconnect coolant hose and tubes. Remove nuts and bolts
securing exhaust manifold. Remove exhaust manifold and gaskets.
Disconnect oil return pipe. Remove turbocharger assembly.
Removal (Stealth & 3000GT Front)
1) Disconnect negative battery cable. Drain engine oil and
coolant. Remove radiator. Disconnect exhaust pipe. Remove air intake
hose, air hoses and air pipe. Remove alternator and belt. Remove oil
dipstick guide.
2) Remove heat protector. Disconnect oxygen sensor electrical
connector. Remove oil return pipe. Remove turbocharger support bracket
and remove turbocharger from exhaust manifold. See Fig. 10.
Fig. 10: Removing Front Turbocharger (Stealth & 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
Removal (Stealth & 3000GT Rear)
1) Disconnect battery cables and remove battery. Drain engine
oil and coolant. Remove accelerator cable. Remove air hose, air pipe
and heat protectors. Disconnect clutch booster vacuum hose. Remove air
Page 693 of 1333
intake hoses and EGR pipe. Disconnect oxygen sensor electrical
connector.
2) Remove oil pipe and EGR valve. Disconnect exhaust fitting
and remove rear heat protector. Remove oil return pipe. Remove
turbocharger assembly. See Fig. 11.
Fig. 11: Removing Rear Turbocharger (Stealth & 3000GT)
Courtesy of Mitsubishi Motor Sales of America.
Inspection
Check turbine and compressor wheels for cracking and other
damage. Make sure turbine and compressor wheels turn smoothly. Check
for oil leakage from turbocharger assembly. Check for proper wastegate
valve operation. See SYSTEM & COMPONENT TESTING article.
Installation
1) To install, reverse removal procedure. Before oil pipe
flare nut (above turbocharger) is installed, pour clean engine oil
into turbocharger. Ensure oil and air hoses are properly installed and
securely clamped.
2) Use new gaskets. Adjust accelerator cable (if necessary).\
Refill engine oil and coolant. Check for oil and coolant leaks.
Tighten all bolts to specification. See TORQUE SPECIFICATIONS table.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE\
\
\
\
\
\
Applications Ft. Lbs. (N.m)
Fuel Tank Nuts ............................. 15-22 (20-30)
Page 705 of 1333
![MITSUBISHI MONTERO 1991 Service Manual \b\
\
\
\
\
\
\
Fluid Levels](/manual-img/19/57332/w960_57332-704.png "MITSUBISHI MONTERO 1991 Service Manual \b\
\
\
\
\
\
\
Fluid Levels")
\b\
\
\
\
\
\
\
Fluid Levels
\b\
\
\
\
\
\
\
Braking System
\b\
\
\
\
\
\
\
Drive Shaft Boots
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
GL-4 Or GL-5
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Automatic Transmission
1987-93 ...................................... 7.6 Qts. (7.2L)
1994 (3.0L SOHC) ............................. 7.6 Qts. (7.2L) \
1994 (3.0L DOHC & 3.5L) ...................... 9.0 Qts. (8.5L) \
1995 ......................................... 7.9 Qts. (7.5L)
Cooling System
1987-88 ...................................... 8.5 Qts. (8.0L)
1989-95
2.6L ........................................ 9.7 Qts. (9.2L)
3.0L ....................................... 10.0 Qts. (9.5L)
1994-95
3.5L ....................................... 10.0 Qts. (9.5L)
Differential
1987-88 ...................................... 1.9 Qts. (1.8L)
Page 707 of 1333
![MITSUBISHI MONTERO 1991 Service Manual Service Or Inspect
\
\
\
\
\
\](/manual-img/19/57332/w960_57332-706.png "MITSUBISHI MONTERO 1991 Service Manual Service Or Inspect
\
\
\
\
\
\")
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Valve Clearance (Jet Valve Only)
\b\
\
\
\
\
\
\
Manual Transmission Oil & Transfer Case
\b\
\
\
\
\
\
\
Carburetor Choke Mechanism & Linkage (If Equipped)
\b\
\
\
\
\
\
\
Disc Brake Pads
\b\
\
\
\
\
\
\
Drum Brake Linings & Rear Wheel Cylinders
\b\
\
\
\
\
\
\
Brake Hoses
\b\
\
\
\
\
\
\
Fuel & Vapor Hoses
\b\
\
\
\
\
\
\
Steering Linkage Seals & Drive Shaft Boots
\b\
\
\
\
\
\
\
Lubricate Ball Joint
\b\
\
\
\
\
\
\
Power Steering Fluid (If Equipped)
\b\
\
\
\
\
\
\
Power Steering Hoses (If Equipped)
\b\
\
\
\
\
\
\
Lubricate Front Wheel Bearing
\b\
\
\
\
\
\
\
Drive Axle Fluid (Without Limited-Slip Differential)
\b\
\
\
\
\
\
\
Lubricate Drive Shaft Joints
\b\
\
\
\
\
\
\
Exhaust System
\b\
\
\
\
\
\
\
Lubricate Upper Control Arm Bushings
\b\
\
\
\
\
\
\
Drive Belt (Water Pump & Alternator)
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Air Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Drive Axle Fluid (With Limited-Slip Differential)
\b\
\
\
\
\
\
\
Automatic Transmission & Transfer Case Fluids
\b\
\
\
\
\
\
\
Engine Oil & Filter
\b\
\
\
\
\
\
\
Engine Coolant
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Page 709 of 1333
![MITSUBISHI MONTERO 1991 Service Manual 37,500 MILE (60,000 KM) SERVICE \
\
\
\
\
\
\
Service](/manual-img/19/57332/w960_57332-708.png "MITSUBISHI MONTERO 1991 Service Manual 37,500 MILE (60,000 KM) SERVICE \
\
\
\
\
\
\
Service")
37,500 MILE (60,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Change Engine Oil
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Engine Oil
1987 ......................................... 5.2 Qts. (5.0L)
1988 ......................................... 5.0 Qts. (4.8L)
1989-92 ...................................... 5.5 Qts. (5.3L)
1993-94 ...................................... 5.2 Qts. (4.9L)
\
\
\
\
\
\
\
\f
45,000 MILE (72,000 KM) SERVICE
45,000 MILE (72,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Fluid Levels
\b\
\
\
\
\
\
\
Braking System
\b\
\
\
\
\
\
\
Drive Shaft Boots
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Page 713 of 1333
![MITSUBISHI MONTERO 1991 Service Manual \b\
\
\
\
\
\
\
Fuel Filter](/manual-img/19/57332/w960_57332-712.png "MITSUBISHI MONTERO 1991 Service Manual \b\
\
\
\
\
\
\
Fuel Filter")
\b\
\
\
\
\
\
\
Fuel Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Ignition Cables
\b\
\
\
\
\
\
\
Camshaft Timing Belt
\b\
\
\
\
\
\
\
Engine Coolant
\b\
\
\
\
\
\
\
Drive Axle Fluid (With Limited-Slip Differential)
\b\
\
\
\
\
\
\
Engine Oil & Filter
\b\
\
\
\
\
\
\
Automatic Transmission & Transfer Case Fluids
\b\
\
\
\
\
\
\
Vacuum Control System Solenoid Valve Air Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
GL-4 Or GL-5
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Automatic Transmission
1987-93 ...................................... 7.6 Qts. (7.2L)
1994 (3.0L SOHC) ............................. 7.6 Qts. (7.2L) \
1994 (3.0L DOHC & 3.5L) ...................... 9.0 Qts. (8.5L) \
1995 ......................................... 7.9 Qts. (7.5L)
Cooling System
1987-88 ...................................... 8.5 Qts. (8.0L)
1989-95
Page 715 of 1333
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Engine Oil
1987 ......................................... 5.2 Qts. (5.0L)
1988 ......................................... 5.0 Qts. (4.8L)
1989-92 ...................................... 5.5 Qts. (5.3L)
1993-95 ...................................... 5.2 Qts. (4.9L)
\
\
\
\
\
\
\
\f
75,000 MILE (120,000 KM) SERVICE
75,000 MILE (120,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Fluid Levels
\b\
\
\
\
\
\
\
Braking System
\b\
\
\
\
\
\
\
Drive Shaft Boots
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
Page 718 of 1333
![MITSUBISHI MONTERO 1991 Service Manual Replace
\
\
\
\
\
\](/manual-img/19/57332/w960_57332-717.png "MITSUBISHI MONTERO 1991 Service Manual Replace
\
\
\
\
\
\")
Replace
\
\
\
\
\
\
\
Air Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Drive Axle Fluid (With Limited-Slip Differential)
\b\
\
\
\
\
\
\
Automatic Transmission & Transfer Case Fluids
\b\
\
\
\
\
\
\
Engine Oil & Filter
\b\
\
\
\
\
\
\
Engine Coolant
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
GL-4 Or GL-5
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Automatic Transmission
1987-93 ...................................... 7.6 Qts. (7.2L)
1994 (3.0L SOHC) ............................. 7.6 Qts. (7.2L) \
1994 (3.0L DOHC & 3.5L) ...................... 9.0 Qts. (8.5L) \
1995 ......................................... 7.9 Qts. (7.5L)
Cooling System
1987-88 ...................................... 8.5 Qts. (8.0L)
1989-95
2.6L ........................................ 9.7 Qts. (9.2L)
3.0L ....................................... 10.0 Qts. (9.5L)
1994-95
3.5L ....................................... 10.0 Qts. (9.5L)
Differential