1991 MITSUBISHI ECLIPSE cruise control

AUTO-CRUISE CONTROL SYSTEM - Trdubleshooting
IGNITIONSWITCH(lG1)
J/B
yl8 y17
C”
COLUMN SWITCH
AUTO-CRUISE
CONTROL
0.85-GW
0
20.85-GOPENEEECToR
E
SIBLE1
c-47 ~ ‘
I
J/B
3 c-55
16
AUTO-CRUISEc-01CONTROL UNIT

14-130AUTO-CRUISE CONTROL SYSTEM - Troubleshooting
AUTO-CRUISE
CONTROL-UNITc-01
1 I_-_-_-_-_-_-__II---------lI
i
t
---------------------C-67s
I I
I II I
%Ic!Y
MOTOR;iW'O;;ON
B-03
5
8t
2
i
r!
__------
5c!
ec!
14 C-67
rHROTTLE;gj&ON
t
3-02
19
r
!4
L
%iV
1 IDLE1 SWITCH
E-051
MPICONTROLC-66
UNIT
KXW-AC-UllllM-NC

AUTO-CRUISE CONTROL SYSTEM - Troubleshooting14L’1.31”
-=cA/T>
SUB
LIN
!z
A
c
0
10A
c3
c3
h'HEN{EY IS?EMOVED
c
2Iu-zn
r
:ONI(IG1) ,INIGNITIONST)SWITCH(IG2)
-1
SIBLE
4
raII31
c-47
1
J/B
C-52
(liIals14r51sl]
IGNITISWITCI
1 J/B10A
3 c-50
7Flimsq’
z
6 c-45
14
LW$NATION
9
I, ,D-05
‘71(2~3~41516~715“‘I0 1lo~llll~l3ll4pm7
WITH
iEK;Si-
#gpT
ALARMSYSTEM I SYSTEMI,
AUTO-CRUI6E,23 CONTROL UNIT
73
i
GND
14
m10
C-67
m
0
KX35-AC-Ul516-NCn
SELF-DIAGNOSISCOt$NECTOR
c-30 :
FRONT 'SIDE
piELRq
REVERSE ,-SIDE

14-132AUTO-CRUISE CONTROL SYSTEM - Troubleshooting
4ci
IGNITIONSWITCHtlGl)
CR”
I
AUTO-CRUISE
CONTROL UNIT
c-01
B
1COLUMN SWITCH
AUTO-CRUISE
>CONTROL SWITCH
T C-06
I
\,4
STOPLIGHT '~------
"ITCH OP?“ONc-03ON
+I1
2
hS3 O
0
s0.65-G
SUB 1LINK
!i
L!
0
L15A
I0.85-GW-0.85-GW1
!5
OPEN
CONNECTORc-02
1IQI2E
;SIBLE
qB
1 d-47
J/B6
C-55
16
AUTO-CRUISEc-01CONTROL UNIT

AUTO-CRUISE CONTROL SYSTEM - Troubleshooting1:4;;1$~”
*,,,’
4-SPEED
AUTOMATIC
;&V&'~;LE
UNIT
--------
JF
rAUTO-CRUISEY5v 9CONTROL UNIT
GNI"
4clmc-55
,J/B
'
r10 c-45=I75 c-54
7
‘pcu1234
m667.3
GNDn
MPICONTROL
UNIT
C-66
4-SPEED
AUTOMATIC
-&$$$)ELE
UNIT
C-60
COMBINATIONKXJS-AC-UlSlBh-NC
El

14-134AUTO-CRUISE CONTROL SYSTEM - Troubleshooting
AUTO-CRUISE
CONTROL-UNITc-01I-----_-_---..------
II------ -----1
(l.BL)(2.0L)1
‘6
I II I
‘h‘s
Y5Y4
"
54
5Iw
I I
1218 C-67_------
eww
16
-L
w
w
! THROTTLE;g;E&ONt
B-02
MOTOR;;iEX;&ON
B-03
MPICONTROLC-66
UNIT

AUTO-CRUISE CONTROL SYSTEM L service Adjustkt Procedw&
03A0258
YSET
03AO258
03AO250
SET
03A025t
JI
SERVICE ADJUSTMENT PROCEDURESNl4FUU
AUTO-CRUISE CONTROL SYSTEM INSPECTION
AUTO-CRUISE CONTROL SWITCH CHECK(1) Turn the ignition key to ON.
(2) Check to be sure that the indicator light within the switch
illuminates when the cruise control switch is switched ON.
(Turn the cruise control switch to the “CRUISE” position.)
AUTO-CRUISE CONTROL SETTING CHECK(1) Switch ON the cruise control switch.
(2) Drive at the desired speed within the range of approxi-
mately 40-145 km/h (25-90 mph).
(3) Press the SET button.
(4) Check to be sure that the speed is the desired constant
speed when the switch is released, and also check to be
sure that the auto cruise indicator light (tithin the combina-tion meter) illuminates.
NOTE1(
If the vehicle speed decreases to approximately 15 km/h
(9 mph) below the set speed, because of climbing a hill for
example, the auto-cruise control will be
cancelled.
SPEED-INCREASE SETTING CHECK
(‘1) Set to the desird speed.
(2) Turn the control switch to RESUME position.
(3) Check to be sure that acceleration continues while the
switch is hold, and that when it is released the constant
speed at the time when it was released becomes the
driving speed.
NOTEEven if, during acceleration, the vehicle speed reaches or
exceeds the high limit [approximately 145 km/h (90
mph)], acceleration will continue, however, when the
switch is released, the set speed (“memorized speed”) will
become the high limit of the vehicle speed.
’ ” ,
SPEED REDUCTION SETTING CHECK(1) Set to the desired speed.
(2) Press the SET button.
(3) Check to be sure that deceleration continues while the
switch is pressed, and that when it is released the
constant speed at the time when it was released becomes
the driving speed.
NOTEIWhen the vehicle speed reaches the low limit [approxi-
mately 40 km/h (25 mph)] during deceleration, the auto-
matic speed control will be
cancelled.

14-136AUTO-CRUISE CONTROL SYSTEM- Service Adjustment Procedures03AQ250
rdjusting
03A0281
AUTO-CRUISE CONTROL CANCELLATION CHECK(1) Set the auto-cruise control.
”(2) Check to be sure that there is a return to ordinary driving,
and that the illumination of the auto-cruise indicator stops,
‘cwhen either of the operations below is performed.
@ The brake pedal is depressed.
@ The clutch pedal is depressed.
@ The shift lever is moved to the “N” or “P” range.
aIT>
@ The auto-cruise control main switch is switched OFF.
@ The ignition switch is turned to OFF.
CHECK OF RETURN TO THE SET SPEED BEFORE
CANCELLATION(1) Set the auto-cruise control.
(2) Check to be sure that the auto-cruise control is
cancelledwhen either of the operations below is performed.
@ The brake pedal is depressed.
@ The clutch pedal is depressed.
@I The shift lever is moved to the “N” range. (3) Turn the control switch to RESUME position and release
(RESUME switch
ONdOFF) while driving at a vehicle
speed of approximately 40 km/h (25 mph) or higher.
(4) After switching RESUME switch to OFF, check to be sure
that there is a return to the auto-cruise control speed before
it will be
cancelled and the vehicle will travel at the constant
speed.
A
ACCELERATOR CABLE, THROTTLE CABLE AND
AUTO-CRUISE CONTROL CABLE INSPECTION
AND ADJUSTMENT(1) Remove the link protector. (Refer to P.14140.)
(2) Check that there are no sharp bends and breaks in the
accelerator cable, throttle cable and auto-cruise control
cable.(3) Turn the ignition switch to the ON position (without starting
the engine) and leave in that condition for approximately 15
seconds.(4) Leave plenty of play in each cable and temporarily install
adjusting nuts A,
B, C and adjusting bolts D.