1991 MITSUBISHI 3000GT oil

INTAKE AND EXHAUST - Intercooler
INTERCOOLER
/REMOVAL AND INSTALLATION18
/?1IO-13Nm
7-9ftJbs.
/Turbocharger
b-ring
05FOOO3MlSTA-
-
I
lo-13Nm7 - 9 ft.lbs.
OSPDOU24Nm
/ 17 ft.lbs.
ANm
7-.9 ft.lbs.
. .-...2.9 ft.lbs.lo-13Nm
’7 - 9 ft.lbs.2
_ .
Removal steps of intercooler right
**I. Air hose Cl *2. Air hose D3. Intercooler duct (RH)l *4. Intercooler rightRemoval steps of intercooler left
l *5. Air hoseG
6. Air pipe A
7. Heat protector F
I)* 8. Air hose Bl *9. Air hose E10. Air pipe BII. Air pope C** 12. Air hose F*I)13. Engine oil cooler
14. Intercooler duct (LH)
l * 15. Intercooler left
lo-13 Nm7 - 9 ft.lbs.OSFOC.02
(When equipped with intercooler left)
l Installation of Front Bumper
(Refer to GROUP 51 - Front Bumper.)Removal steps of air intake hose
16. Connection of boost hose
17. Air hoseA
18. Connection of air flow sensor connector
I)* 19. Air intake hose A** 20. Air intake hose B*a 21. Air intake hose C
22. Air cleaner
23. Air by-pass hose
24. Air by-pass valve
1 TSB Revision

15-12INTAKE AND EXHAUST - lntercooier
SERVICE POINT OF REMOVALMlSTSAC
13. REMOVAL OF ENGINE OIL COOLERIDisconnect the hose from the engine oil cooler and remove
the engine oil cooler only.
IL)
INSPECTIONMISTCAB
lCheck the intercooler fins for bending, damage, or foreign
matter.
lCheck the intercooler hoses for cracking, damage, or wear.
Air Intake hose B
Air hose
05FOO21
SERVICE POINTS OF INSTALLATIONMlSTDAC
21. INSTALLATION OF AIR INTAKE HOSE C
/ 20. AIR
INTAKE HOSE B
/ 19. AIR INTAKE HOSE A
Engaging the notch with the
n mark at points indicated by
the arrows, insert air intake hoses B and C until seated.
Insert the turbocharger end of air intake hoses B and C
completely.
15. INSTALLATION OF INTERCOOLER LEFT / 12. AIR HOSEF
/ 9. AIR HOSE E / 8. AIR HOSE B / 5. AIR HOSE G
Aligning the marks at the points indicated by the arrows,
insert securely into the stepped portion of the pipe or until
seated.
CautionBe careful not to allow any foreign matter to get into
the hoses, pipes, or the intercooler itself.
4.INSTALLATION OF INTERCOOLER RIGHT / 2. AIR HOSED
/ 1. AIR HOSE C
Aligning the marks at the points indicated by arrows, insert
securely into the stepped portion of the pipe.
CautionBe careful not to allow any foreign matter to get into
the hoses, pipes, or the intercooler itself.
1 ~
LJ~TSB Revision

INTAKE AND EXHAUST - Intake Manifold.15-1705LOO84
ProtrusionFRONT
ProtrusionA\
\ProtrusionProtrusidnOIL0857
FRONT
Intake mamfold7lN0090
APPLY~~ lubricant
INSPECTIONMlIMCATZCheck the following points; replace the part if a problem is
found.
INTAKE MANIFOLD(1) Check for damage or cracking of any part.
(2) Clogging of the negative pressure (vacuum) outlet port, or
clogging of the gas passages.
(3) Check deflection of installation surface with straight edge
and thickness gauge.
Standard value
: 0.15 mm (.0059 in.) or less
Limit
: 0.2 mm (.008 in.)
SERVICE POINTS OF INSTALLATIONMISMDAH
13. INSTALLATION OF INTAKE MANIFOLD GASKETInstall with gasket protrusions in the position illustrated.
10. INSTALLATION OF INTAKE MANIFOLD MOUNTING
NUT
Tighten the intake manifold mounting nuts one bank after
the other by the following ‘procedure.
(1) Tighten the nuts in the front bank to 3 to 5 Nm (2.2 to
3.6 ft.lbs.).
(2) Tighten the nuts in the rear bank to 12 to 15 Nm (9 to 11ft.lbs.).
(3) Tighten the nuts in the front bank to 12 to 15 Nm (9 to
11 ft.lbs.).
(4) Repeat steps (2) and (3) one more time respectively.
9. INSTALLATION OF INTAKE MANIFOLD MOUNTING
NUT
Apply lubricant sparingly to the intake manifold mounting
nuts.
TSB Revision

15-18INTAKE AND EXHAUST - Turbocharger (Front)
TURBOCHARGER (FRONT)
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operationl Removal and Installation of Radiator(Refer to GROUP 14 - Radiator.)l Removal and Installation of Transmission
l Rerr
IPipeioval and Installation of Front Exhaust(Refer to P.15-31.)
lJl QG!?
IMlSLA-AI
40 - 47 ft.lbs.
1\29 - 11 ft.lbs.Removal steps
** 1. Air hose C*+2. Air intake hose B*+ 3. Air hose D4. Air hose Al *5. Air hose B.6. Air pipe B
l +7. Air hose E8. Air pipe C
9. Drive belt(Refer to GROUP 11 - Service
Adjustment Procedures.)
10. Alternator assembly(Referto GROUP 16-Alternator.)
11. Engine oil level gauge guide
12. Heat protector B-13Nm
‘9 ft.lbs.
-‘25
05FOO43
13. Water pipe A
14. Water pipe B
15. Connection of oxygen sensor
16. Turbocharger
& fitting assembly
17. Gasket
18. Ring
l * ** 19. Oxygen sensor
20. Turbocharger stay
21. Exhaust fitting
22. Gasket
23. Oil return pipe
l * 24. Turbocharger assemblyl *25. Air conditioner compressor
26. Tension pulley bracket
27. Air conditioner compressor bracket
28. Oil pipe
I
LJ
1 TSB Revision

INTAKE AND EXHAUST - Turbocharger (Front)15-19
05FOO2(
SERVICE POINTS OF REMOVALM15LBAE
19. REMOVAL OF OXYGEN SENSORDisconnect the connector of the oxygen sensor, and install
the special tool to the oxygen sensor.
25. DISCONNECTION OF AIR CONDITIONER COMPRES-
SORDisconnect air conditioner compressor with hoses from the
bracket.
NOTEThe removed air conditioner compressor should be fas-
tened (by using rope, etc.) in a position that will not interfere
with the removal/installation of the turbocharger assembly.
INSPECTION
TURBOCHARGER ASSEMBLY CHECKMlSLCADl
lVisually check the turbine wheel and the compressor wheel
for cracking or other damage.
l Check whether the turbine wheel and the compressor
wheel can be easily turned by hand.
l Check for oil leakage from the turbocharger assembly.
lCheck whether or not the waste gate valve remains open. If
any problem is found, replace the part after disassembly.
OIL PIPE AND OIL-RETURN PIPE CHECKCheck the oil pipe and oil-return pipe for clogging, bending, or
other damage.
If there is clogging, clean it.
SERVICE POINTS OF INSTALLATIONMllLDAE
24. INSTALLATION OF TURBOCHARGER ASSEMBLYClean the alignment surfaces shown in the illustration.
Supply clean engine oil through the oil pipe installation hole
of the turbocharger assembly.
CautionWhen cleaning, care must be taken so that a piece of
the gasket does not enter the oil passage hole.
TSB Revision

INTAKE AND EXHAUST - Turbocharger (Rear)15-21
TURBOCHARGER (REAR)
iREMOVAL AND INSTALLATION
/
id
Post-installation ODerationIl Installation of Front Exhaust Pipe(Referto P.15-31.)l Refilling of the Engine Coolant
(Refer to GROUP 00 - Maintenance
l Adjustment of Accelerator Cable1~~~~o~~ GROUP 13 - Engine
lo-13Nm7 - 9 ft.lbs.
6.
7 55-65Nmb
5 40 - 47 ft.lbs.i18Nm’
d13 ft.lbs.
MlSLA-B
0-nng
05FOOO3Removal steps
1. Battery2. Connection of accelerator cable
** 3, pg,t;eye)l * 4.
AirpipeA5. Heat protector F
6. Clutch booster vacuum hose
7. Connection of accelerator cable
(pedal side)
I)+8. Air intake hose AO+9. Air intake hose Cl * I)* 10. Oxygen sensor
11. Heat protector D12. EGR pipe
9Nmv 10 //--!
-7 ft.lbs.45 Nm33 ft.lbs.LIZ-15NmOSFOO419- 11 ft.lbs.
13.Eye boltl * 14. Oil pipe15.EGR valve16. Water pipe A
17. Water pipe B
18.Exhaust fitting
19. Heat protector E
20.Gasket21,. Turbocharger & return pipe assembly
22. Oil return pipe
l * 23. Turbocharger assembly24.Gasket25.Ring26. Exhaust fitting stayTSB Revision

INTAKE AND EXHAUST - Turbocharger (Rear)
0
Comrxessorwheel \u ~i, rOlR0182
I05FOO19
SERVICE POINT OF REMOVALM15LBAF
10. REMOVAL OF OXYGEN SENSOR
Disconnect the connector of the oxygen sensor, and install
’the special tool to the oxygen sensor.
d,
INSPECTION
TURBOCHARGER ASSEMBLY CHECK
M15LCADZ
lVisually check the turbine wheel and the compressor wheel
for cracking or other damage.
l Check whether the turbine wheel and the compressor
wheel can be
easily.turned by hand.
l Check for oil leakage from the turbocharger assembly.
lCheck whether or not the waste gate valve remains open. If
any problem is found, replace the part after disassembly.
OIL PIPE AND OIL-RETURN PIPE CHECKCheck the oil pipe and oil-return pipe for clogging, bending, or
other damage.
If there is clogging, clean it.
SERVICE POINTS OF INSTALLATIONMlBLDAF
23. INSTALLATION OF TURBOCHARGER ASSEMBLYClean the alignment surfaces shown in the illustration.
CautionWhen cleaning, care must be taken so that a piece of
the gasket does not enter the oil passage hole.
14. INSTALLATION OF OIL PIPESupply clean engine oil through the oil pipe installation hole
of the turbocharger assembly.
10. INSTALLATION OF OXYGEN SENSORUse the special tool to install the oxygen sensor.
TSB Revision

INTAKE AND EXHAUST - Turbocharger
INSPECTION
TURBOCHARGER
15-25MllLGAB
(I) Manually open and close the waste gate valve to make sure
it operates freely.
(2)Inspect the oil passage in the cartridge for signs of deposits
or blockage.
(3) Clean the inlet section of the compressor cover with a rag.
Inspect it for signs of contact with the compressor turbine.
If worn, replace it.
L/
O-ring
3EN23C3062
snap ring Chamfered
.
v cartr~d~om,,ir
,jFcover
WI61 NO070
SERVICE POINTS OF REASSEMBLYM15LHAC7. INSTALLATION OF O-RING
Coat the inner surface of a new O-ring with a thin film of
engine oil, and set it in the groove of the cartridge
assembly.
Caution
Be careful not to damage the O-ring while installing itas oil leakage could result.
6. INSTALLATION OF CARTRIDGE ASSEMBLY
(1) Coat the outer circumference of the cartridge assembly
O-ring with a thin film of engine oil.
(2) Install the cartridge assembly on the compressor cover
by aligning the dowel pin.
CautionWhen installing the cartridge assembly on the
compressor cover, be careful not to damage the
compressor wheel blades.5. INSTALLATION OF SNAP RING
Place the cartridge assembly with the compressor cover
faced down and install the snap ring.
Caution
Install the snap ring with the tapered side of its outsidediameter up.
TSB Revision4. INSTALLATION OF TURBINE HOUSING
Install the compressor cover and cartridge assembly on the
turbine housing with the dowel pin in alignment.
Caution
1.Be careful not to damage the blades of the turbine
wheel.2. Be careful to install the turbine housing in the
correct direction.