1990 MAZDA 232 fuel tank removal

Fl INDEX
1. Fuel tank
Removal I hspection /
I nstalIation
1. . . . . . . . . . . . . . * . . . ..I..... ,*,.
page Fl-10
2. 4x4 control unit (Fuel pump control unit)
Inspection .__...._..................__..._. page Fl-12
Replacement _. . _. _. _. _. . _ _ _. . . _ . _. _. . . . _.
page
Fl - 12
3. Transfer pump switch
Removal / lnstaltation . . . . . . . . . . . . . .._ page Fl-13
inspection .._......_.. . . ..-_. . . .._....... page F1 -I 3 93GOFl-702
4. Transfer pump
inspection _........._....._................ page Fl-13
Replacement.. . .__.-.. . . . . . . . . . . . . . . , U.-e
page
FI -13
5. Exhaust system components
Removat I hspection I
Installation
.**...**..a*..........*..*..__.
page fl-15
Fl-2

SUPPLEMENTAL SERVICE INFORMATION, FUEL SYSTEM Fl
SUPPLEMENTAL SERVICE INFORMATION
The following points in this section are changed in comparison with Mazda 323 Workshop Manuals
(I 203-I U-89F, 1204-I O-89F, I2061 O-89F).
fuel tank
l Removal I Inspection I Installation
4x4 control unit (Fuel pump control unit)
l Inspection procedure added
l Replacement procedure added
Transfer pump switch
l Inspection procedure added
l Replacement procedure added
Transfer pump
l Inspection procedure added
l Replacement procedure added
Exhaust system components
l Removai I Inspection I installation 93GOF? -706
FUELSYSTEM
PRECAUTION
Fuel Pressure Release and Sewicing Fuel System
Fuel in the fuel system remains under high pressure when the
engine is not running.
a) Before disconnecting any fuel line, release the fuel
pres-
sure from the fuel system to reduce the possibility of injury
or fire.
1. Start the engine.
2. Push the rear seat cushion buttons and remove the
cushion.
3. Disconnect the fuel pump connector.
4. After the engine stalls, turn off the ignition switch.
5. Reconnect the fuel pump connector and install the rear
seat cushion.
b) Use a rag as protection from fuel spray when disconnect-
ing the hoses.
Plug the hoses after removal.
c> When inspecting the fuel system, use a suitable fuel pres-
sure gauge.
Caution
l Install hose clamps to secure tile fuel pressure
gauge to the fuel filter and the fuel main hose to pre-
vent fuel leakage.
Priming Fuel System
After releasing the fuel pressure for repairs or inspection, the
system must be primed to avoid excessive cranking when first
starting the engine. Follow the
steps below.
I. Connect the diagnosis connector terminals F/P and GND
with a jumper wire.
2. Turn the ignition switch ON for approx. IO sec. and check
for fuel leaks.
3. Turn the ignition switch OFF and remove the jumper wire.
Fl-9

Fl FUEL. SYSTEM
FUEL TANK
Removal / inspection I Installation
Warning
l Before performing the following operation, release the fuel pressure from the fuel system to
reduce the possibiIity of injury or fire. (Refer to page Fl-9.)
l When removing the fuel tank, keep sparks, cigarettes, and open flames away from it.
l Before repairing the fuel tank, clean it throughly with steam to remove all explosive gas.
1. Remove in the order shown in the figure.
2. Inspect the fuel tank components visually and repair or replace as necessary.
3. Install in the reverse order of removal, referring to Installation Note.
FUEL PUMP (MAIN) TRANSFERPU
4341 (4.4-6.2, 3245)
GASKET, REPLACE
ET, REPLACE
4it-55 (4.3 -5.6, 3041)
Nm (m-kg, ft-lb)
a?cnc% .7*7

FUEL SYSTEM, TRANSFER PUMP CONTROL SYSTEM Fl
Note
l Drain the fuel from the fuel tank before removing the tank.
I. Fuel pump cover
2.
Fuel pump connector
3. Fuel hoses
Installation
Note . . . . . . . . . . . . , . . . . . . . . . . . . . . _ . . . . . below
4. Exhaust pipe
Removal / lnstaltatjon . . . . . . . . . . . . .._. page Fl -I 5
5. Propeller shaft
Removal / installation ._..._....,_.._..._.. Section L 6. Fuel fiIler hose, breather hose, and
evaporation
hoses
Installation Note . . . ..*..**......*........~_.....~.
below
7. Fuel tank straps
8. Fuel tank
inspect for cracks and corrosion
93m=: -708
I B FUEL FILLER HOSE
22%
-.
-L
0 F /
@,
M
E -J
03UOFX-Bf 4
93GOFl-709
Installation Note
1. Push the ends of the main fuel hose, fuel return
hose, and
evaporative hoses onto the fuel tank fittings at least 25mm
(1.0 in).
2. Push the fuel filler hose onto the fuel tank pipe
and filler pipe
at ieast 35mm (1.4 in).
TRANSFER PUMP CONTROL SYSTEM
SYSTEM OPERATION ’
1. Turn the ignition switch ON and verify that the fuel
gauge
indicates more than half and that the transfer pump oper-
ating sound is heard.
Warning
l If the fuel level is less than one half, this inspec-
tion cannot be performed.
2. Ground the transfer pump connector terminal-wire (Y/L) with
a jumper wire and verify that the transfer pump stops.
3. Remove the jumper wire and verify that the transfer pump
begins operation after approx. 50 sec.
4. If not as specified, check the following parts.
l 4x4 control unit (Fuel pump control unit).
(Refer to page F-I-1 2.)
l Transfer pump. (Refer to page FI-I 3.)
l Transfer pump switch. (Refer to page Ff -13.)

lNDEX F2
4x4 CONTROL UNIT
(FUEL PUMP
CONTROL UNIT)
SERVICE, SECTION SEAT
1. Fuel tank
Removal / Inspection I
lnstailation . . . . .._........._._....... 1 . . . . page F2-51
2. Injector _
Volume test ~..........~..~..,...~..~....~. page F2-56
3. Fuel pump resistor/relay [BP TURBO]
System operation . . ._. . . ._. _ . . . . . . . . . . . page F2-56
Inspection . . . . . . . . . . . . . . . . . . . *. . . . . . . . . . . . . page F2-56 4. Fuel pump control unit [BP TURBO]
Inspection *....,...,.........I..... * . . . . . . . page F2-53
Replacement . . . . . . . . . . . . . . . . . . . . . . . . ..-... page F2-53
5. Transfer pump switch
Removal I InstaNation . . . . . . . . . , ..,... page F2-54
Inspection ..a . . . . . . . . . . . . . . . . . . * . . ..I.. e... page F2-54
6. Transfer pump
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page F2-54
Replacement ,...,_..... b . .._._......_.... page F2-54
1. Exhaust system
RemovA I Inspection I InstaNation
BP SOHC . . . . __.._......... _........... page F2-57
BP TURBO _.. . . . . . .._.. . . . . . . . . . . . . . . . page FZ-58
F2-3

SUPPLEMENTAL SERVICE INFORMATION F2
SUPPLEMENTAL SERVICE INFORMATION
The following points in this section are changed in comparison to the Mazda 323 Workshop Manual
[I 203-I U-89F (Europe) or 120410-89F {Australia)].
intake air system components [BP Turbo]
l Removalllnspectionll nstaltation
WASTEGATE [BP Turbo]
l Inspection
WASTEGATE SULENOlD VALVE [BP Turbo]
l Inspection
Turbocharger [BP Turbo]
l Inspection
l Removalllnstaltation
Air bypass valve [BP Turbo]
l Removal/hstallation
l 1 nspection
lntetcoolet [BP Turbo]
l RemovaMnspection/tnstaltation
Fuel tank
l Removal ! Inspection I Installation
Fuel pump control unit [BP Tubto]/4x4 control unit [BP SOHC]
l 1 nspection
l Replacement
Transfer pump switch
l Inspection
l Replacement
Transfer pump
l Inspection
l Replacement
Fuel pump resistor/relay
l System operation
l Inspection
injector [8P Turbo]
l Volume test
Exhaust system components
l Removal / 1 nspection / Installation
Engine control unit (ECU) [BP Turbo]
l Terminal voftage
Oxygen sensor [BP Turbo]
l Inspection
l Replacement
Knock sensor [BP Turbo]
l Replacement 93GOFZ736
F2-25

FUEL SYSTEM F2
FUEL TANK
Removal I inspection / Instatlation
Warning
l Before performing the following operation, release the fue1 pressure from the fuet system to
reduce the possibitity of injury or fire. (Refer to page F2-50.)
l When removing the fuel tank, keep sparks, cigarettes, and open flames away from it.
l Before repairing the fuel tank, clean it throughly with steam to remove all explosive gas.
1. Remove in the order shown in the figure.
2. Inspect the fuel tank
components and repair or replace as necessary.
3. tnstall in the reverse order of removal, referring to Installation Note.
FUEL PUMP TRANSFER PUMP
0 SEAL RUBBER, REPLACE 7
A SSL
40-55 (4.1-56, 30-41)
N-m {m-kg, Mb)
93GOF2-771
F2-51

F2 FUELSYSTEM
Note
l Drain the fuei from the fuel tank before removing the tank.
1. Fuel pump cover
2. FueI pump connector
3. Fuel hoses
Installation Note ..___........_.....__......_...._. below
4. Exhaust pipe
Removal / installation . . . . . . . .__._. . , . . . FZ-57, 58
5. Propeller shaft
Removal ! Installation .._._...._....._.._.. Section L 6. Fuel filier hose, breather hose, and
evaporation hoses
tnstal!ation Note ..m..,* . . . . ...*-. *..,- . . . . m...-e.. below
7. Fuel tank straps
8. Fuel tank
Inspect for cracks and corrosion
93GOF2-772
0 FUEL FILLER HOSE
03UOFX- 13! installation Nate
1. Push the ends of the main fuel hose, fuel return hose, and
evaporative hoses onto the fuel tank fittings at least 25mm
(1 .O in).
2. Push the fuel filler hose onto the fuel tank pipe and filler pipe
at least 35mm (1.4 in).
TRANSFER PUMP CONTROL SYSTEM
System Operation
I. Turn the ignition switch ON and verify that the fuel gauge
indicates more than half and that the transfer pump oper-
ating sound is heard.
Warning
l If the fuel level is less than one half, this inspec-
tion cannot be performed.
2. Ground the transfer pump connector terminai-wire (Y/L) with
a jumper wire and verify that the transfer pump stops.
3. Remove the jumper wire and verify that the transfer pump
begins operation after approx. IO sec.
4. If not as specified, check the following parts.
l Fuel pump control unit. [BP turboJ
(Refer to page F2-53.)
4x4 control unit [BP SOHC] (Refer to page Fl-12.)
l Transfer pump. (Refer to page F2-54.)
. Transfer pump switch. (Refer to page F2-54.)
93GOF2-774
F2-52