1990 MAZDA 232 fuel

FUEL SYSTEM F2
2. Remove the service hole cover of the transfer pump.
3. Disconnect the transfer pump connectors.
4. Disconnect the fuel hose,
5.
Remove the transfer pump.
6. Install in the reverse order of removal. Caution
l Install a new seat rubber.
03UOFX-826
Disassembly I Assembly
Caution
l Prevent contaminants from entering the transfer pump.
1. Disassemble in the order shown in ,the figure.
2. Assemble in the reverse order of disassembly.
3. Verify that the transfer pump operates correctly after assembling it.
HOSE, REPLACE
@
1. Fuel filter
2. Rubber mount
3. Transfer pump 4. Fuel hose
5. Transter pump switch assembly
93GOF2-77:
FZ-55

F2 FUEL SYSTEM
93GOF2-775
1 93GOF2-78(
93GOF2-78:
1
93GOF2-78;
-
93GOF2-783
FUEL PUMP RESISTOR/RELAY
System Operation
I. Remove the rear seat cushion.
2,
Measure the voltage at the fuel pump connector terminal
A {G/O).
Voltage
r Crankinq Approx. 12V
I
I- Others t ACKXOX. I OV i
3. If not within specification, perform the following inspection,
and repair or replace if necessary.
l Fuel pump resistor/relay resistance. (Refer to below.)
l ECU II terminal voltage. (Refer to page F2-60.)
l Wiring harness and connector.
inspection
1.. Disconnect the connector.
2. Ground the fuel pump resister relay terminal D.
3. Apply 12V to terminal C and check for continuity between
terminals A and B.
Terminal C
12 applied
ov Continutty between A and B
NO
Yes
4. Measure the resistance between terminals E and F.
Resistance : 0.62-0.66Q [at 20% (68OF)l
INJECTOR
Volume Test
1. Remove the injectors with the delivery pipe.
2. Affix the injectors to the delivery pipe with wire.
Caution
l Affix the injectors firmly to the delivery pipe so that
no movement of the-injectors is possible.
Warning
l Be extremely careful when working with fuel.
Always work away from sparks or open flames.
3. Connect the SST to the battery and injector.
4. Check the injection volume with a graduated container.
Injection volume:
BP SUHC....44-47 cc (2.68-2.87 cu in)/15 sec.
BP Turbo
. ...87-105 cc (5.31 -6.41 cu in)/15 sec.
Caution
l When using the SST, make sure of the SST num-
ber and use correct one.
5. If nut correct, replace the injector(s).

F2 CONTROL SYSTEM
Terminal voltage [BP TURBO]
eminal input Output , 1 Connected to Test condition Correct voltage Remark
IA - - Battery Constant Approx. 12V for backup
15 0 Main relay OFF Approx. OV
(FUEL INJ relay) tgnltlon switch
-
ON Approx. 12V
1c 0 1 Ignition switch Wniie cranking Approx. 1 OV
-
(START)
lgnrtron switch ON Approx. OV
ID 0 Self -Diagnosis Test switch at “SELF-TEST” With Self-
Checker Lamp illuminated ior 3 sec. after ignition Approx. 5V Diagnosis Check-
(Monitor lamp) switch OFF* ON er and System
Lamp not illuminated after 3 sec. Approx. 12V Se’ector
Test switch at
“02 MONITOR” at idle
Monitor lamp illuminated Approx. 5V
Test switch at
“02 MONITOR” at idle
Monitor lamp not illumrnated Approx. 12’4
-lE - - - -
- -
1F 0 Self-Diagnosis Buzzer sounded for 3 sec. after ignition
Below 2.5V l With Self-
Checker switch OFF -+ ON Diagnosis
(Code Number)
Buzzer not sounded after 3 sec. Approx. 12V Checker and
Buzzer sounded Below 2.9 System Selector
l With System
Buzzer not sounded Approx. 12V Selector test
switch at
“SELF-TEST’ ’
I I 1G
0 Igniter
7H
0 Solenoid vahe
(Wastegate)
l!
0 Fuel pump
resistor/relay
I
lJ I r-Tcreiay Ignition switch ON
ld!e
Engine speed below 5,300 rpm
Engine speed above 5,300 rpm
While cranking
Idle
Ignition switch ON
AK switch ON at idle 1 Approx. OV
-
Approx. 0.2V
Approx. 12V
-
Below 1.5V
Approx. 1 OV
-
I3elow 15V
Approx. 12V
Below 2.5V
AIC switch OFF at idle Approx. 12V
-
IK 0 Diagnosis System Selector test switch at
connector
(TEN terminal)
1L - - -
- -
-
IM
t 0
1 Ground (Australia) Constant Below 1 .OV Not used
(Except Australia)
F2-60

CONTROL SYSTEM F2
Incorrect voltage Possible cause
Always OV
l ROOM 10A fuse burned l Open circuit in wiring from ROOM 10A fuse to ECU termrnal IA
Always OV
I l Main relay maifunctlon l Open or short crrcu~t in wirrng from main relay to ECU termrnal 1 B
Always OV (Srarrer turns)
l Open or short circuit in wiring from ignition switch to ECU terminal 1C
Always UV
l Main relay (FUEL INJ relay} malfunctron l Open circuit in wiring from main relay to diagnosis connector terminal + B l Open or short circuit in wiring from dragnosls connector terminal MEN to
ECU terminal 1D
Always approx. 12V
I . Poor connection at ECU connector
l ECU matfunction
Always approx. 5V
l ECU malfunction
-
I -
Always below No disptay on Self- . Main relay (FUEL INJ retay) malfunction (Refer to page F3-142)
2.5V Diagnosis Checker l Open circuit in wiring from main relay to diagnosis connector termjnal + B
“88” displayed and
l Open or short circuit in wiring from diagnosis connector terminal FEN to
buzzer sounds con- ECU terminal 1 F
tinuously
Always approx. 12V
l Poor connection at ECU connector l ECU malfunction
Always OV
l Short circuit in wiring from igniter to ECU terminal tG
Atways OV or approx. 12V
l Refer to Code No.42 Troubleshooting (Refer to page F2-30)
Always approx. 12V
l Fuel pump resistor/relay malfunction
Always OV
l Open or short circuit in wiring from ECU terminal 1 I to resistor/retay
Always below
A/C does not operate
l AJC relay malfunction
23 l Open circuit in wiring from ignition switch to NC relay l Open circuit in wiring from A/C relay to ECU terminal IJ
A/C switch OFF but
l Short circuit in wiring from A/C relay to ECU terminal IJ
AIC operates
l ECU matfunction
Always approx. t2V
Always below 1 .OV
l Poor connection at ECU connector l ECU malfunction
l Short circurt in wiring from diagnosis connector terminal TEN to ECU termi-
nal 1K
Always approx. 12V
l Open circutt in wiring from diagnosis connector terminal TEN to ECU termi-
nal lK
l Open c~rcud in wiring from diagnosis connector terminal GND to ground
Always above 1 .OV
I
l Open circuit in wiring from ECU terminal 1 M to ground
F2-61

CONTROLSYSTEM F2
I
7
Incorrect voltage Possible cause
Always OV l Open or short circuit in wjring from ECU terminal 2s to buzzer
Always OV or approx. 12V
1 l Refer to Code No.25 Troubieshootlng
Always OV
1
l Marn relav (FUEL INJ relay) malfunction
/ l Open or shbrt circuit in wi&g from injector to ECU terminal 2U or 2V
Always approx. 12V
l ECU malfunctron
Always OV or approx. t2V
l Refer to Code No.34 TroubleshootIng
Always OV or approx. 12V
l Refer to Code No.26 Troubleshooting
Always OV
l Open or short circuit KI wiring from ECU terminal 2Y to relay
f2-67