1990 MAZDA 232 relay

SUPPLEMENTAL SERVICE INFORMATION F2
SUPPLEMENTAL SERVICE INFORMATION
The following points in this section are changed in comparison to the Mazda 323 Workshop Manual
[I 203-I U-89F (Europe) or 120410-89F {Australia)].
intake air system components [BP Turbo]
l Removalllnspectionll nstaltation
WASTEGATE [BP Turbo]
l Inspection
WASTEGATE SULENOlD VALVE [BP Turbo]
l Inspection
Turbocharger [BP Turbo]
l Inspection
l Removalllnstaltation
Air bypass valve [BP Turbo]
l Removal/hstallation
l 1 nspection
lntetcoolet [BP Turbo]
l RemovaMnspection/tnstaltation
Fuel tank
l Removal ! Inspection I Installation
Fuel pump control unit [BP Tubto]/4x4 control unit [BP SOHC]
l 1 nspection
l Replacement
Transfer pump switch
l Inspection
l Replacement
Transfer pump
l Inspection
l Replacement
Fuel pump resistor/relay
l System operation
l Inspection
injector [8P Turbo]
l Volume test
Exhaust system components
l Removal / 1 nspection / Installation
Engine control unit (ECU) [BP Turbo]
l Terminal voftage
Oxygen sensor [BP Turbo]
l Inspection
l Replacement
Knock sensor [BP Turbo]
l Replacement 93GOFZ736
F2-25

F2 SELF-DIAGNOSlS FUNCTION
Troubleshooting
If a malfunction code number is shown on the SST (49 l-l01 8 9Ai, 49 B019 9AO), check for the cause
using the chart related to the code number shown, [Regarding code numbers except 05, 24, and 42, refer
to “Troubleshooting” in Workshop Manual [I 203-I O-89F (Europe) or 1204-f 0-89F (Australia)].
r C :ODE No. 05 (KNOCK CONTROL UNIT)-BP TUR80
;TEP
2
3 I INSPECTION
Check knock sensor and knock control unit
circuit for poor connectlon ACTtON
Yes Repalr or replace connector
Check knock control unit terminal voltage with
ignition switch ON
Check that voltage at ECU terminal 2J is
approx. 4V at idle
rs7 page F2-64 Yes Recheck ECU connector for poor
connection
4 If OK, replace ECU
4 If not OK, repair or replace connector
NO Repair wiring harness (R/Y) between
ECU terminal 2J and knock control unit
93GOF2-7:
Circuit Diagram
I
ECU
IGNITION
SWITCH
15A BATTERY
MAIN
RELAY
(FUEL 1N.J)
l W/L Y/i3 G/O W RIB R/L
YIL
jr- -- - - 1 BlLG
-
-
MCK CONTROL
I
. :
MAIN RELAY (FUEL INJ)
W/G BIW
C&=&A
KNOCK CONTROL UNIT
W/R EMLG RN Y/L
1
KNOCK SENSOR

SELF-DIAGNOSIS FUNCTION F2
:UDE No. 24 (FUEL PUMP RESISTOR/RELAY)-BP TURBO
STEP INSPECTION ACTtON
1 1 Disconnect connector from ECU and check if
1 battery voltage exists at connector terminal 1 I (L) Yes Check ECU terminal connector for poor
connection
with ignition switch ON
e If OK. replace ECU
c=> If not OK, repair or replace connector
NO Go to next step
2 In same condltlon as Step 1, check if battery
Yes Repair wiring harness (W/R)
voltage exists at resistor/relay connector terminai- I
wire (W/R)
NO Go to next step
3 Check if there is continuity between fuel pump
Yes Check for short or open circuit
in wiring
res!stor/relay terminals C (‘W/R) and D (L) from main relay (FUEL INJ relay) to
t resistor/relay
NO Replace resistor/relay
93GOF2-74 1 Circuit Diagram
IGNITION
SWITCH DIAGNOSIS
CONNECTOR
rl
F/P TERMINAL *
BATTERY
IGNlTlON
0fP
W/R
FUEL
PUMF
B
c W/R 7
FUEL PUMP
- RESISTOR/RELAY
\I
I/
ECU MAIN RELAY
Of1
W/G . LGrf Grw l v L/O R/Y LGlR YfL B/LG
RIB 1
I GIB J 1 1 [ WR LG ] Y , UW~LGIw/ * 1 W ] 810 WIG BfW
I
I I I
1 I I
I
&J,~&&&l&&c!zr5& &l~&cLa~~c!zch&&&&~
1~ IS 10 10 IM 1K II tC 1E 1C IA 2Y 2w 2u 2s 20 20 28.4 2K 21 2G 2E 2C 2A
IV 17 ?R IP 1N 1~ IJ III IF ro :8
rrrrrT?rrTT
BRff t BIG 1 R/W ! t/B 1 WIB 1 W/R
BIL UY O/B WN
CIRCUIT OPENING RELAY
FUEL PUMP FUEL PUMP RESlSTOR/RE~Y
v WIRBIP
B - LG
93GOF2.74
F2-29

F2 SELF-DIAGNOSlS FUNCTION
XIDE No. 1 42 (SOLENOID VALVE - WASTEGATE)-BP TURBO STEP
tNSPECTiON
ACTION
1
Disconnect connector from ECU and check if Yes Check ECU terminal connector for poor
battery voltage exists at connector terminal f H connection
(O/B) with Ignition switch ON
e If OK, replace ECU
4 tf not OK, repalr or replace connector
No Go to next step
2 in same condition as Step 1, check if battery Yes Repair wiring harness voltage extsts at solenoid valve connector
terminal-wire
NO Go to next step
3 Check if solenoid valve is OK
Yes Check for short or open circuit in wiring
.r3 page F2-46 from main relay (FUEL INJ relay) to
solenoid valve
NO Replace solenoid valve
Circuit Diagram
BA-iTERY
15A k
IGNITION SWITCH v /\: ./
WIG
B/w O/B
‘L a,
d
MAIN RELAY
(FUEL INJ)
WASTEGATE
SOtENOlD VALVE
ECU
WASTEGATE MAIN RELAY (FUEL INJ)
SOLENOfD VALVE
RIB 011 GIB WIG * LGIY L GM,
l v L/R
I
A WIG %fw
W/R
1u
10 1M 1K 71 B O/B
I I
i
B&Y B/L B;G UY Rh’ * I
I
IJB d/B WiB Wff W/R W/R B
F2-30

F2 FUEL SYSTEM
93GOF2-775
1 93GOF2-78(
93GOF2-78:
1
93GOF2-78;
-
93GOF2-783
FUEL PUMP RESISTOR/RELAY
System Operation
I. Remove the rear seat cushion.
2,
Measure the voltage at the fuel pump connector terminal
A {G/O).
Voltage
r Crankinq Approx. 12V
I
I- Others t ACKXOX. I OV i
3. If not within specification, perform the following inspection,
and repair or replace if necessary.
l Fuel pump resistor/relay resistance. (Refer to below.)
l ECU II terminal voltage. (Refer to page F2-60.)
l Wiring harness and connector.
inspection
1.. Disconnect the connector.
2. Ground the fuel pump resister relay terminal D.
3. Apply 12V to terminal C and check for continuity between
terminals A and B.
Terminal C
12 applied
ov Continutty between A and B
NO
Yes
4. Measure the resistance between terminals E and F.
Resistance : 0.62-0.66Q [at 20% (68OF)l
INJECTOR
Volume Test
1. Remove the injectors with the delivery pipe.
2. Affix the injectors to the delivery pipe with wire.
Caution
l Affix the injectors firmly to the delivery pipe so that
no movement of the-injectors is possible.
Warning
l Be extremely careful when working with fuel.
Always work away from sparks or open flames.
3. Connect the SST to the battery and injector.
4. Check the injection volume with a graduated container.
Injection volume:
BP SUHC....44-47 cc (2.68-2.87 cu in)/15 sec.
BP Turbo
. ...87-105 cc (5.31 -6.41 cu in)/15 sec.
Caution
l When using the SST, make sure of the SST num-
ber and use correct one.
5. If nut correct, replace the injector(s).

F2 CONTROL SYSTEM
Terminal voltage [BP TURBO]
eminal input Output , 1 Connected to Test condition Correct voltage Remark
IA - - Battery Constant Approx. 12V for backup
15 0 Main relay OFF Approx. OV
(FUEL INJ relay) tgnltlon switch
-
ON Approx. 12V
1c 0 1 Ignition switch Wniie cranking Approx. 1 OV
-
(START)
lgnrtron switch ON Approx. OV
ID 0 Self -Diagnosis Test switch at “SELF-TEST” With Self-
Checker Lamp illuminated ior 3 sec. after ignition Approx. 5V Diagnosis Check-
(Monitor lamp) switch OFF* ON er and System
Lamp not illuminated after 3 sec. Approx. 12V Se’ector
Test switch at
“02 MONITOR” at idle
Monitor lamp illuminated Approx. 5V
Test switch at
“02 MONITOR” at idle
Monitor lamp not illumrnated Approx. 12’4
-lE - - - -
- -
1F 0 Self-Diagnosis Buzzer sounded for 3 sec. after ignition
Below 2.5V l With Self-
Checker switch OFF -+ ON Diagnosis
(Code Number)
Buzzer not sounded after 3 sec. Approx. 12V Checker and
Buzzer sounded Below 2.9 System Selector
l With System
Buzzer not sounded Approx. 12V Selector test
switch at
“SELF-TEST’ ’
I I 1G
0 Igniter
7H
0 Solenoid vahe
(Wastegate)
l!
0 Fuel pump
resistor/relay
I
lJ I r-Tcreiay Ignition switch ON
ld!e
Engine speed below 5,300 rpm
Engine speed above 5,300 rpm
While cranking
Idle
Ignition switch ON
AK switch ON at idle 1 Approx. OV
-
Approx. 0.2V
Approx. 12V
-
Below 1.5V
Approx. 1 OV
-
I3elow 15V
Approx. 12V
Below 2.5V
AIC switch OFF at idle Approx. 12V
-
IK 0 Diagnosis System Selector test switch at
connector
(TEN terminal)
1L - - -
- -
-
IM
t 0
1 Ground (Australia) Constant Below 1 .OV Not used
(Except Australia)
F2-60

CONTROL SYSTEM F2
Incorrect voltage Possible cause
Always OV
l ROOM 10A fuse burned l Open circuit in wiring from ROOM 10A fuse to ECU termrnal IA
Always OV
I l Main relay maifunctlon l Open or short crrcu~t in wirrng from main relay to ECU termrnal 1 B
Always OV (Srarrer turns)
l Open or short circuit in wiring from ignition switch to ECU terminal 1C
Always UV
l Main relay (FUEL INJ relay} malfunctron l Open circuit in wiring from main relay to diagnosis connector terminal + B l Open or short circuit in wiring from dragnosls connector terminal MEN to
ECU terminal 1D
Always approx. 12V
I . Poor connection at ECU connector
l ECU matfunction
Always approx. 5V
l ECU malfunction
-
I -
Always below No disptay on Self- . Main relay (FUEL INJ retay) malfunction (Refer to page F3-142)
2.5V Diagnosis Checker l Open circuit in wiring from main relay to diagnosis connector termjnal + B
“88” displayed and
l Open or short circuit in wiring from diagnosis connector terminal FEN to
buzzer sounds con- ECU terminal 1 F
tinuously
Always approx. 12V
l Poor connection at ECU connector l ECU malfunction
Always OV
l Short circuit in wiring from igniter to ECU terminal tG
Atways OV or approx. 12V
l Refer to Code No.42 Troubleshooting (Refer to page F2-30)
Always approx. 12V
l Fuel pump resistor/relay malfunction
Always OV
l Open or short circuit in wiring from ECU terminal 1 I to resistor/retay
Always below
A/C does not operate
l AJC relay malfunction
23 l Open circuit in wiring from ignition switch to NC relay l Open circuit in wiring from A/C relay to ECU terminal IJ
A/C switch OFF but
l Short circuit in wiring from A/C relay to ECU terminal IJ
AIC operates
l ECU matfunction
Always approx. t2V
Always below 1 .OV
l Poor connection at ECU connector l ECU malfunction
l Short circurt in wiring from diagnosis connector terminal TEN to ECU termi-
nal 1K
Always approx. 12V
l Open circutt in wiring from diagnosis connector terminal TEN to ECU termi-
nal lK
l Open c~rcud in wiring from diagnosis connector terminal GND to ground
Always above 1 .OV
I
l Open circuit in wiring from ECU terminal 1 M to ground
F2-61

CONTROL SYSTEM F2
Incorrect voltage
Always below 1 .OV Possible cause
l Throttle sensor misadjustment l Short circuit in wiring from throttle sensor to ECU terminal IN l ECU malfunction
Always approx. f 2V
Atways below 1 .OV (Stopfights OK)
Always below 1 .OV
l Throttle sensor misadjustment l Open circuit in wiring from throttle sensor to ECU terminal IN l Open ctrcuit in wiring from throttle sensor to ECU terminal 20
l Open crrcurt in wiring from stoplight switch to ECU terminal 10
l P/S pressure switch malfunction l Short circuit in wirrng from P/S pressure switch to ECU termrnai 1 P
l ECU malfunction
Always approx. 12V
Atways below 2.5V (Btower fan OK) . P/S pressure switch malfunction
l Open circuit in wiring from P/S pressure switch to ECU terminal I P l Open circuit in wiring from P/S pressure switch to ground
l A/C switch malfunction l Short circuit in wiring from A/C switch to ECU terminal 1 Q l Poor connection at ECU connector l ECU malfunction
Always approx. 12V (Blower fan OK)
l ’ A/C switch malfunction l Open c~rcurt in wiring from NC switch to ECU terminal 1Q l ken circuit H-I winnu from A/C switch to blower control switch
Always below 1.W
l Open or short circuit in wiring from fan relay to ECU terminal IR
(Electrkal cooling fan UK} l ECU malfunctron
Always below 1 .OV (Blower fan OK)
l Short crrcutt in wiring from blower control swrfch to ECU terminal IS l Poor connection at ECU connector l ECU malfunction
Always approx. 12V (Blower fan OK)
Always below Illumination lamp
1.w ON when rear
window defroster
switch ON 1
l Open circurt in wrring from blower control switch to ECU terminat IS
I
l Open or short circuit rn wiring from rear window defroster switch to ECU
terminal 1 T
ftlumination lamp
never ON
l Open circuit in wiring from ignition switch to rear window defroster switch
l Rear window defroster switch malfunction I
Always below 1 .OV (Headlights OK)
l Open or short circurt in wiring from headlight relay to ECU termtnal 1 U
Always below 1 .OV
Always approx. l2V
l Neutral switch malfunction l Clutch switch malfunction l Short circuit in wiring from ECU terminal IV to neutral or clutch switch
l Neutral switch maifunctton l Clutch switch malfunction l Open circuit in wiring from ECU terminal IV to neutral or clutch swttch
l Poor connection at ECU connector
93GOFZ789
F2-63