1989 FORD SIERRA engine

Wheels
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pressed steel or alloy
Size:
Saloon, Hatchback and Estate models:
Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 x 4.50 in, 13 x 5.50 in, or 14 x 5.50 in
Alloy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 x 5.50 in
P100 models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 x 5.50 in
Tyre sizes
Note: Manufacturers often modify tyre sizes and pressure recommendations. The following is intended as a guide only. Refer to your vehicle
handbook or a Ford dealer for the latest recommendations
Saloon and Hatchback models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 R 13H, 165 R 135, 165 R 13T, 185/70 R 13H, 185/70 R 135,
185/70 R13T, 195/60 R 14H, 195/60 VR 14 or 195/65 R 14T
Estate models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175 R 13H, 175 R 135,175 R 13T, 195/70 R 13H, 195/65 R 14T,
195/60 R 14H or 195/60 VR 14 P100 models 185R 14 8PR
Tyre pressures (cold): lbf/in2
(bar):FrontRear
All Saloon, Hatchback and Estate models with normal load* . . . . . . .26 (1.8)26 (1.8)
All Saloon and Hatchback models with full load . . . . . . . . . . . . . . . .29 (2.0)36 (2.5)
Estate models with full load:
175 R 13H, 175 R 135,175 R 13T, 195/70 R 13H and 195/65 R14T .29 (2.0)48 (2.8)
195/60 R 14H and 195/60 VR 14 . . . . . . . . . . . . . . . . . . . . . . . . . .29 (2.0)36 (2.5)
P100 models with light load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 (1.8)36 (2.5)
P100 models with full load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 (3.5)65 (4.5)
*Normal load is defined as up to three passengers (or equivalent). For sustained high speeds add 1.5 lbf/in2
(0.1 bar) for every 6 mph (10 km/h)
over 100 mph (160 km/h)
†A light load is defined as one passenger plus up to 100 kg (220 lb) payload
Torque wrench settingsNmlbf ft
Roadwheel nuts
Wheelnuts:
Saloon, Hatchback and Estate models (steel and alloy wheels) . . . .70 to 10052 to 74
P100 models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 to 9063 to 66
Hub nuts:
Saloon, Hatchback and Estate models . . . . . . . . . . . . . . . . . . . . . . .310 to 350229 to 258
P100 models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .390 to 450288 to 332
Front suspension
Strut upper mounting nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 to 5230 to 38
Hub carrier-to-strut pinch-bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 to 9257 to 68
Crossmember-to-underbody bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 to 9052 to 66
Engine mounting-to-crossmember nut:
Saloon, Hatchback and Estate models . . . . . . . . . . . . . . . . . . . . . . .50 to 7037 to 52
P100 models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 to 5830 to 43
Anti-roll bar-to-lower arm nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 to 11052 to 81
Anti-roll bar U-clamp-to-underbody bolts . . . . . . . . . . . . . . . . . . . . . . .55 to 7041 to 52
Lower arm-to-hub carrier balljoint nut . . . . . . . . . . . . . . . . . . . . . . . . . .65 to 8548 to 63
Lower arm inner pivot bolt:
Stage 1 (“clamping”torque) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4533
Loosen fully, then Stage 2 (“snug” torque) . . . . . . . . . . . . . . . . . . . . .1511
Stage 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tighten through a further 90º
Rear suspension
Saloon, Hatchback and Estate models:
Lower arm-to-crossmember pivot bolts . . . . . . . . . . . . . . . . . . . . . . .80 to 9559 to 70
Front guide plate-to-underbody bolts . . . . . . . . . . . . . . . . . . . . . . . .41 to 5130 to 38
Front guide plate-to-crossmember bolt . . . . . . . . . . . . . . . . . . . . . . .10074
Suspension/final drive unit rear mounting-to-underbody bolts (gold
coloured) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6044
Suspension/final drive unit rear mounting-to-final drive unit rear cover
bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 to 5030 to 37
Anti-roll bar-to-underbody bracket bolts . . . . . . . . . . . . . . . . . . . . . .20 to 2515 to 18
Hub carrier/brake backplate-to-lower arm bolts*:
Type X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 to 6438 to 47
Type Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 to 10059 to 74
Hub nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250 to 290185 to 214
*See Section 15
11•2Suspension and steering

Torque wrench settings (continued)Nmlbf ft
P100 models:
Shock absorber-to-chassis crossmember bolt . . . . . . . . . . . . . . . . . . .60 to 7044 to 52
Leaf spring-to-front bracket bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157 to 196116 to 145
Leaf spring-to-spring shackle bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157 to 196116 to 145
Spring shackle-to-underbody bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 to 8559 to 63
Axle-to-leaf spring U-bolt nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 to 5829 to 43
Manual steering
Steering gear-to-crossmember bolts:
Stage 1 (“clamping” torque) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4533
Loosen fully, then Stage 2 (“snug” torque) . . . . . . . . . . . . . . . . . . . . .1511
Stage 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tighten through a further 90º
Steering column adjuster through-bolt . . . . . . . . . . . . . . . . . . . . . . . . . .6 to 84 to 6
Tie-rod end locknut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 to 6842 to 50
Tie-rod end-to-hub carrier nut* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 to 3215 to 24
Tie-rod-to-steering rack balljoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 to 8853 to 65
Steering wheel nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 to 5533 to 41
Intermediate shaft-to-inner column clamp bolt . . . . . . . . . . . . . . . . . . .20 to 2515 to 18
Flexible coupling-to-steering gear clamp nut . . . . . . . . . . . . . . . . . . . . .24 to 2617 to 19
Column mounting pinch-bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 to 5533 to 41
Pinion retaining nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 to 10052 to 74
Slipper plug† . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 to 53 to 4
*Tighten nut to specified torque and then tighten to next available split pin hole
†Tighten nut to specified torque and then loosen off 60º to 70º
Power steering (where different to manual steering)
Tie-rod to steering rack balljoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 to 7752 to 57
Flexible coupling-to-steering gear clamp bolt . . . . . . . . . . . . . . . . . . . .16 to 2012 to 15
Intermediate shaft-to-inner column clamp bolt . . . . . . . . . . . . . . . . . . .16 to 2012 to 15
Pinion locknut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 to 4727 to 35
Slipper plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 to 42 to 3
Pump rear support bar nut and bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 to 5130 to 38
Pump mounting bracket-to-engine bolts . . . . . . . . . . . . . . . . . . . . . . . .52 to 6438 to 47
Pump pulley bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 to 127 to 9
Fluid hose-to-pinion housing bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 to 2615 to 19
Fluid pressure hose-to-pump union . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 to 3119 to 23
Fluid return hose-to-pump union . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 to 2012 to 15
The front suspension is of independent
MacPherson strut type incorporating coil
springs and integral telescopic shock
absorbers. The lower end of each strut is
attached to a hub carrier, which carries the
wheel hub and bearings, and the brake
assembly. The lower end of each hub carrier
is attached to a suspension lower arm by a
sealed balljoint. The inboard ends of the lower
arms are attached to the front suspension
crossmember and the lower arms thus
provide lateral location for the strut
assemblies. The upper end of each strut is
bolted to a suspension turret on the vehicle
body. An anti-roll bar is mounted to the rear of
the lower arms, and resists the roll tendency
of the front suspension.
On Saloon, Hatchback and Estate models,
the rear suspension is also of independent
type, incorporating semi-trailing arms, coil
springs and telescopic shock absorbers. The
semi-trailing arms are attached to the
suspension crossmember at their forward
ends, and to the hub carriers at the rear. Thecoil springs are located between the
semi-trailing arms and the vehicle underbody.
On Saloon and Hatchback models, the shock
absorbers are mounted behind the coil
springs, but on Estate models they are
concentric with the coil springs. On some
Estate models the shock absorbers are of the
self-levelling type. The suspension
crossmember is attached to the vehicle
underbody, and to the final drive unit. Certain
models are fitted with an anti-roll bar which is
mounted to the rear of the final drive unit, and
is attached to the semi-trailing arms by
connecting links.
The rear suspension on P100 models
consists of a beam axle located and
supported by a leaf spring on each side, and
utilizing telescopic shock absorbers to control
vertical movement. The hub and brake
assemblies are attached directly to each side
of the axle. The axle is bolted to the leaf
springs using U-bolts and counterplates, and
the shock absorbers are attached to the
counterplates at their lower ends and the
vehicle underbody at their upper ends.
The steering gear is of the conventional
rack and pinion type located ahead of the
front wheels. Movement of the steering wheelis transmitted to the steering gear by means
of a shaft containing a universal joint. The
front hub carriers are connected to the
steering gear by tie-rods, each having an inner
and outer balljoint. Power-assisted steering is
available on some models, assistance being
provided hydraulically by an engine-driven
pump.
Removal
1Remove the steering gear.
2Support the engine with a jack and
interposed block of wood under the sump.
3Unscrew and remove the engine mounting
nuts from the top of the mountings in the
engine bay (see illustration).
4Raise the engine slightly with the jack, and
ensure that it is safely supported, and just
clear of the engine mounting rubbers.
5Unscrew and remove the nuts, washers and
pivot bolts securing the lower arms to the
crossmember, and pull the arms from the
crossmember. Note that the pivot bolt heads
face to the rear of the vehicle.
2Front suspension crossmember
-removalandrefitting
1General information
Suspension and steering 11•3
11

6Where applicable, remove the brake pipes
from the clips on the crossmember, taking
care not to strain them, and detach any cables
or electrical leads which may be secured with
clips or cable-ties, noting their positions.
7Support the crossmember with a jack, then
unscrew and remove the four mounting bolts
(see illustration).
8Lower the crossmember and withdraw it
from under the vehicle.
9If desired, the engine mountings can now
be unbolted from the crossmember.
Refitting
10Refitting is a reversal of removal, but bear
in mind the following points.
11Do not tighten the lower arm pivot bolts
until the weight of the vehicle is resting on its
wheels. This is to prevent “wind up” of the
rubber bushes which will occur when the
vehicle is lowered if the bolts have been
tightened with no load on the suspension. The
following procedure must be used when
tightening the pivot bolts. Tighten the bolt to
the specified “clamping” torque, then loosen
the bolt fully. Re-tighten to the specified
“snug” torque and then further tighten the bolt
through the specified angle.
12Refit any cables or electrical leads in their
original positions, where applicable.
13When lowering the engine onto its
mountings, ensure that the locating pegs on
the mountings engage with the holes in the
mounting brackets.
Note: A balljoint separator tool will be
required for this operation.
Removal
1To improve access, raise the front of the
vehicle on ramps. Do not jack the vehicle up
at this stage. Apply the handbrake.
2Unscrew and remove the nut, washer and
pivot bolt securing the relevant lower arm to
the crossmember (see illustration).
3Remove the anti-roll bar-to-lower arm
securing nut and recover the dished washer
and plastic cover (where applicable) (see
illustration).4Ensure that the handbrake is applied, jack
up the front of the vehicle and support on axle
stands (see “Jacking and Vehicle Support”).
5Remove the split pin and unscrew the
castellated nut from the lower arm balljoint.
Using a balljoint separator tool, disconnect
the lower arm from the hub carrier. The lower
arm can now be withdrawn from the vehicle.
Recover the remaining dished washer and
plastic cover (where applicable) from the end
of the anti-roll bar.
Overhaul
6If the lower arm has been removed due to a
worn balljoint, the complete arm must be
renewed.
7The anti-roll bar compliance bushes can be
renewed as described in Section 8, but note
that the bushes on both sides of the vehicle
must be renewed at the same time. The lower
arm inner pivot bush can be renewed as
described in Section 9.
Refitting
8To refit the lower arm, proceed as follows.
9Fit the shallow dished washer (colour
coded black or green) and the plastic cover
(where applicable) to the end of the anti-roll
bar, then refit the lower arm to the anti-roll
bar. Fit the remaining plastic cover (where
applicable) and the deep dished washer
(colour coded yellow or black) and refit the
securing nut. Do not tighten the nut at this
stage. Note that the convex faces of the
dished washers must face the lower arm.10Reconnect the balljoint to the hub carrier,
refit the castellated nut and tighten to the
specified torque. Fit a new split pin.
11Locate the end of the lower arm in the
crossmember and refit the pivot bolt, washer
and nut. If necessary, push the outer rim of
the roadwheel in order to line up the holes in
the lower arm bush and the crossmember.
Note that the pivot bolt head should face to
the rear of the vehicle. Do not tighten the bolt
at this stage.
12Lower the vehicle so that its weight is
resting on the roadwheels, and bounce the
vehicle to settle the suspension.
13Tighten the lower arm pivot bolt, following
the procedure given in Section 2.
14Tighten the anti-roll bar-to-lower arm
securing nut to the specified torque.
15Lower the vehicle from the ramps, if not
already done.
Note: A spring compressor tool will be
required if the strut is to be dismantled.
Removal
1Loosen the relevant front roadwheel nuts,
apply the handbrake, jack up the front of the
vehicle and support on axle stands (see
“Jacking and Vehicle Support”).
2Remove the roadwheel. On P100 models
mark the position of the roadwheel in relation
to one of the wheel studs before removal.
3Remove the front brake caliper but do not
disconnect the hydraulic hose. Support the
caliper on an axle stand to avoid straining the
hose.
4Where applicable, unbolt the ABS wheel
sensor from the hub carrier and detach the
wire from the clip on the strut. Unplug the
connector and place the sensor to one side.
5Unscrew and remove the pinch-bolt which
secures the hub carrier to the strut. Using a
suitable lever, such as a cold chisel, lever the
hub carrier clamp legs and wedge them apart.
6Lever the suspension lower arm
downwards to separate the hub carrier from
the bottom of the strut.
4Front suspension strut -
removal, overhaul and refitting
3Front suspension lower arm -
removal,overhaul and refitting
11•4Suspension and steering
2.3 Engine mounting nut (arrowed)
3.3 Front anti-roll bar-to-lower arm
securing nut (arrowed)3.2 Front suspension lower arm-to-
crossmember pivot bolt and nut
2.7 Front suspension crossmember
mounting bolts (arrowed)

7Working in the engine compartment,
unscrew the strut upper mounting nut, at the
same time supporting the strut from below.
Use a 6 mm Allen key inserted in the end of
the strut piston rod to prevent the rod from
turning as the upper mounting nut is
unscrewed (see illustration). On some
models, the upper mounting nut may be fitted
with a plastic cover. Note the upper mounting
cup under the nut.
8Withdraw the strut from under the wing of
the vehicle.
Overhaul
9To dismantle the strut, proceed as follows.
10Using spring compressors, compress the
coil spring. Do not attempt to compress the
spring without using purpose-made spring
compressors, as the spring is under
considerable tension, and personal injury may
occur if it is suddenly released (see
illustration).
11Hold the piston rod as described in
paragraph 7, unscrew the nut from the pistonrod and remove the lower cup, bearing, spring
seat, gaiter, coil spring and bump stop (see
illustration).
12Working in the engine compartment,
remove the upper cup and nylon spacer, and
if required prise out the rubber insulator.
13Clean all the components and examine
them for wear and damage. Check the action
of the shock absorber by mounting it vertically
in a vice and operating the piston rod several
times through its full stroke. If any uneven
resistance is evident, the shock absorber
must be renewed. Renew any worn or
damaged components as applicable.
Refitting
14Reassembly and refitting is a reversal of
dismantling and removal, bearing in mind the
following points.
15When reassembling, ensure that the gaiter
is fitted over the bump stop, and that the ends
of the coil spring are correctly located on the
spring seats. Also ensure that the bearing is
correctly located on the upper spring seat.
16Fit the nylon spacer over the piston rod
before fitting the strut to the top mounting.
17Tighten all fixings to the specified torque.
18On P100 models align the previously
made marks on the roadwheel and wheel
stud.Note: A balljoint separator tool will be
required for this operation.
Removal
1Loosen the relevant front roadwheel nuts,
apply the handbrake, jack up the front of the
vehicle and support on axle stands (see
“Jacking and Vehicle Support”).
2Remove the roadwheel. On P100 models
mark the position of the roadwheel in relation
to one of the wheel studs before removal.
3Remove the front brake caliper but do not
disconnect the hydraulic hose. Support the
caliper on an axle stand, or suspend it with wire
from the coil spring to avoid straining the hose.
4Mark the position of the brake disc in
relation to the drive flange, and on Saloon,
Hatchback and Estate models, remove the
retaining screw or spire washer(s), as
applicable, and remove the disc. On P100
models, unscrew the five retaining nuts and
remove the wheel adapter plate and disc.
5Where applicable, unbolt the ABS wheel
sensor from the hub carrier and unplug the
wiring connector. Place the sensor to one side.
6Remove the split pin and unscrew the
castellated nut securing the tie-rod end to the
hub carrier. Using a balljoint separator tool,
disconnect the tie-rod end from the hub carrier.
7Repeat the procedure given in the previous
paragraph for the lower arm-to-hub carrier
balljoint.
8Unscrew and remove the pinch-bolt which
secures the hub carrier to the strut (see
illustration). Using a suitable lever, such as a
cold chisel, lever the hub carrier clamp legs
and wedge them apart. Withdraw the hub
carrier from the strut.
Refitting
9Refitting is a reversal of removal, but use
new split pins on the castellated nuts, and
align the previously made marks on the brake
disc and hub. Tighten all fixings to the
specified torque.
10On P100 models align the previously
made marks on the roadwheel and wheel
stud.
5Front hub carrier -removaland
refitting
Suspension and steering 11•5
11
5.8 Unscrewing the hub carrier-to-strut
pinch-bolt
4.11 Cross-section of the front strut upper mounting
A Bearing
B Nylon spacer
C Upper cupD Rubber insulator
E Lower cup
F Spring seatG Bump stop
H Gaiter
4.10 Suspension strut fitted with spring
compressors
4.7 Hold the strut piston rod with a 6 mm
Allen key when unscrewing the upper
mounting nut

6Turn both tie-rods in the same direction to
correct the steering wheel position. As a
rough guide, 19º of tie-rod rotation will
change the steering wheel position by 1º. To
correct a clockwise error at the steering
wheel, rotate both tie-rods anti-clockwise
(when viewed from the left-hand side of the
vehicle), and the reverse to correct an anti-
clockwise error. Both tie-rods must be rotated
by the same amount.
7Tighten the bellows clips and the tie-rod
end locknuts when adjustment is correct.
Lower the vehicle.
Removal
1Set the front wheels in the straight-ahead
position.
2Disconnect the battery negative lead.
3Remove the driver’s side lower facia trim
panels.
4Remove the screws and withdraw the
steering column upper and lower shrouds
(see illustrations). 5Unscrew the two crosshead screws and
withdraw the two combination switches from
the column.
6Remove the screw from the bonnet release
lever and remove the lever.
7Working in the engine compartment,
unscrew the bolt securing the intermediate
shaft to the inner column, swivel the clamp
plate to one side, and disconnect the
intermediate shaft (see illustration).
8Unscrew the nuts securing the outer
column to the facia.
9Disconnect the multi-plugs and withdraw
the column assembly upwards (see
illustration).
Refitting
10Refit the column assembly in the car and
tighten the upper mounting nuts lightly.
Loosen the mounting pinch-bolt.
11Temporarily fit the upper column shroud
and adjust the position of the steering column
until there is a gap of 5.0 mm (0.2 in) between
the shroud and the facia (see illustration).
12Tighten the pinch-bolt and the mounting
nuts and remove the upper column shroud.
13With the steering wheel in the
straight-ahead position, reconnect theintermediate shaft and tighten the clamp plate
bolt to the specified torque.
14Refit the bonnet release lever and
combination switches and reconnect the
multi-plugs.
15Refit the steering column shrouds and
trim panels.
16Reconnect the battery negative lead.
Note: A new adjuster locknut and washer
must be used on reassembly.
Dismantling
1To dismantle the adjuster assembly,
proceed as follows.
2Remove the locknut and washer securing
the adjuster through-bolt (see illustration).
3Remove the through-bolt, adjuster handle,
locking plates, sliders and washers, then
unclip the spring assembly.
Reassembly
4Reassemble the components as follows.
5Refit the spring to the adjuster assembly
bracket.
25Steering column adjuster -
dismantling and reassembly
24Steering column - removal
and refitting
Suspension and steering 11•15
11
24.4b . . . and lower shroud
24.11 Upper column shroud-to-facia gap adjustment
X = 5.0 mm (0.2 in)
24.9 Steering column components
A Direction indicator cam
B Thrustwashers
C BearingsD Outer column
E Spring
F Inner column
24.7 Intermediate shaft-to-inner column
universal joint and clamp plate (arrowed)24.4a Remove the steering column upper
shroud . . .

6Align the washers, sliders and locking
plates, ensuring that the handle locking plate
is fitted so that the cut-out and Ford logo are
positioned as shown (see illustration).
7Coat the through-bolt threads with a
suitable thread-locking compound, then refit
the through-bolt and the adjuster handle,
ensuring that all components are engaged.
8Position the handle in the locked position,
and secure the through-bolt with a new
locknut and washer.
Removal
1Apply the handbrake, jack up the front of
the vehicle and support on axle stands.
2Working in the engine compartment,
unscrew the bolt securing the intermediate
shaft to the inner column, swivel the clamp
plate to one side, and disconnect the
intermediate shaft.
3Unscrew and remove the clamp bolt
securing the flexible coupling to the steering
gear (see illustration).
4Mark the coupling in relation to the pinion,
then pull off the intermediate shaft and
remove it from the vehicle. The pinion has a
master spline, but making alignment marks
will aid refitting (see illustration).
Refitting
5Refitting is a reversal of removal, but align
the marks on the coupling and pinion, and
tighten all bolts to the specified torque.
Note: A balljoint separator tool will be
required for this operation.
Removal
1Set the front wheels in the straight-ahead
position. Ensure that the steering lock is
engaged and remove the ignition key.
2Apply the handbrake. Loosen the front
roadwheel nuts, jack up the front of the
vehicle and support on axle stands.
3Remove the roadwheels. On P100 models,
mark the position of the roadwheels in relation
to the wheel studs.
4Unscrew and remove the clamp bolts
securing the intermediate shaft flexible
coupling to the steering gear.
5If the original steering gear is to be refitted,
mark the coupling in relation to the pinion. The
pinion has a master spline, but making
alignment marks will aid refitting.
6Slacken the tie-rod end locknuts (see
illustration).
7Remove the split pins and unscrew the
castellated nuts from the tie-rod end-to-hub
carrier balljoints.
8Using a balljoint separator tool, disconnect
the tie-rod ends from the hub carriers.9Unscrew the two steering gear-to-front
suspension crossmember securing bolts, and
withdraw the steering gear from under the
vehicle.
10If required, remove the tie-rod ends.
Refitting
11Refitting is a reversal of removal, bearing
in mind the following points.
12If new steering gear is being fitted, the
central pinion position can be ascertained by
halving the number of turns required to move
the rack from lock to lock.
13Where applicable, align the marks made
on the coupling and pinion.
14When tightening the steering gear-to-front
suspension crossmember bolts, the following
procedure should be used. Tighten the bolts
to the specified “clamping” torque, then
loosen the bolts fully. Re-tighten to the
specified “snug” torque and then further
tighten the bolts through the specified angle.
15Tighten all fixings to the specified torque,
and use new split pins on the balljoint
castellated nuts.
16On P100 models, align the previously
made marks on the roadwheels and wheel
studs.
17On completion, check the front wheel
alignment.
Note: New power steering fluid hose O-rings
will be required when refitting.
Removal
1The procedure is as described for manual
steering gear with the following differences
(see illustration).
2Before removing the steering gear from the
suspension crossmember, place a suitable
container beneath the steering gear. Unscrew
the single bolt securing the power steering
fluid hoses to the pinion housing. Unscrew the
hose unions and drain the power steering
fluid. Plug the ends of the hoses and the
steering gear apertures, or cover them with
masking tape to prevent dirt ingress.
28Power steering gear
- removal and refitting
27Manual steering gear -
removaland refitting
26Steering intermediate shaft
and flexible coupling -
removal and refitting
11•16Suspension and steering
25.6 Cut-out and Ford logo (A) must be
positioned as shown when reassembling
adjustable steering column
26.4 Master spline location on the steering
gear pinion and intermediate shaft
coupling26.3 Intermediate shaft-to-steering gear
flexible coupling
25.2 Adjustable steering column assembly
A Adjuster handle
B Locking plates
C Through-bolt
D Sliders
E Spring

Refitting
3When refitting the fluid hoses, use new
O-rings, and take care not to overtighten the
unions. Note that with the unions fully
tightened it is still possible to rotate and move
the hoses.
4On completion of refitting, bleed the power
steering fluid circuit (Section 34).
Note: New power steering fluid hose O-rings
will be required when refitting.
All engines except 1.8 litre (R6A)
CVH and 2.0 litre DOHC
1Place a suitable container under the power
steering pump, unscrew the fluid hose unions,
and drain the fluid. Ensure that fluid is not
allowed to spill onto the alternator.
2Remove the drivebelts and unbolt the
power steering pump pulley if necessary to
ease removal.
3Unbolt the rear support bar from the pump
and the engine block (see illustration).
4Unbolt the pump from its mounting bracket,
and withdraw the pump from the engine.
5Refitting is a reversal of removal, noting the
following points.
6Tension the drivebelts correctly.
7When refitting the fluid hoses, use new
O-rings, and take care not to overtighten the
unions. 8On completion of refitting, bleed the power
steering fluid circuit.
1.8 litre (R6A) CVH engine
9The removal and refitting procedures are
basically the same as described below for the
2.0 litre DOHC engine, except that the pump
is mounted on a bracket above the alternator
on the front left-hand side of the engine.
2.0 litre DOHC engine
10The pump is mounted on a bracket on the
front right-hand side of the cylinder block.
11Place a suitable container under the
pump, unscrew the fluid pipe unions, and
drain the fluid.
12Remove the drivebelt which also drives
the coolant pump and alternator.
13Prevent the pulley from rotating using a
strap wrench (which can be improvised using
an old drivebelt and a large socket and
wrench), and unscrew the three pulley
securing bolts. Withdraw the pulley.
14Unscrew the three pump securing bolts
from the front of the pump bracket, and the
single bolt from the rear of the bracket, and
withdraw the pump (see illustrations).
15Refitting is a reversal of removal, bearing
in mind the following points.
16Reconnect the fluid unions using new O-
rings.
17On completion, bleed the power steering
fluid circuit.
Note: New fluid hose O-rings will be required
when refitting.
Removal
1Clean around the hose unions on the
steering gear. Place a suitable container
beneath the steering gear, then remove the
single bolt securing the hoses to the pinion
housing, unscrew the hose unions and drain
the power steering fluid.
2Clean around the hose unions on the pump.
Place a suitable container beneath the pump,
unscrew the hose unions, and drain any
remaining fluid. Ensure that no fluid is allowed
to spill onto the alternator.3If the hoses are to be left disconnected for a
long period of time, plug the ends of the
hoses and the apertures in the steering gear
and pump, or cover them with masking tape
to prevent dirt ingress.
Refitting
4Refit in reverse order using new O-rings.
5On completion top-up the fluid and bleed
the system.
1Unscrew the filler cap from the power
steering pump reservoir and top-up the fluid
level to the maximum mark using the specified
fluid.
2Disconnect the low tension negative lead
from the ignition coil and crank the engine
several times for two second periods while
slowly turning the steering wheel from
lock-to-lock. Top-up the fluid level if
necessary and continue cranking the engine
until the fluid is free of air bubbles.
3Reconnect the coil lead and start the
engine. Check the system for leaks.
4Switch off the engine and refit the filler cap.
5Drive the vehicle for a few miles to warm up
the fluid and expel any remaining air, then
stop the engine and make a final fluid level
check.
1Remove the tie-rod end.
2Unscrew and remove the tie-rod end
locknut from the tie-rod.
3Remove the clips and slide the gaiter from
the tie-rod and steering gear.
4Slide the new gaiter over the tie-rod and
onto the steering gear. Where applicable,
make sure that the gaiter seats in the cut-outs
in the tie-rod and steering gear.
5Secure the gaiter with new clips.
6Refit the tie-rod end locknut to the tie-rod.
7Refit the tie-rod end.
Note: A balljoint separator tool will be
required for this operation.
Removal
1Loosen the relevant front roadwheel nuts,
apply the handbrake, jack up the front of the
vehicle and support on axle stands.
2Remove the roadwheel. On P100 models
mark the position of the roadwheel in relation
to one of the wheel studs before removal.
3Make alignment marks on the tie-rod and
tie-rod end, then loosen the locknut by a
quarter of a turn.
33Tie-rod end - removal and
refitting
32Steering gear rubber gaiter -
renewal
31Power steering fluid circuit
- bleeding
30Power steering fluid hoses
- removal and refitting
29Power steering pump
- removal and refitting
11•18Suspension and steering
29.3 Power steering pump rear support bar
bolts (arrowed)
29.14b Power steering pump rear securing
bolt29.14a Unbolt the power steering pump
pulley for access to the front pump
securing bolts (arrowed)