1988 JEEP CHEROKEE warning
[x] Cancel search: warningPage 1176 of 1378
be caused by
faulty alignment ....... A ............. Require alignment.
Part has been changed,
affecting alignment .... A ....... Require alignment check.
Pull, shown to be caused
by faulty alignment .... A ............. Require alignment.
Steering wheel
off-center ............. 2 ............. Suggest alignment.
Tire wear, shown
to be caused by
faulty alignment ....... A ............. Require alignment.
Wander, shown
to be caused by
faulty alignment ....... A ............. Require alignment.
\
\
\
\
\
\
\
WHEELS AND TIRES
TIRES
These guidelines do not apply to split rims. Some vehicle
manufacturers restrict replacement of tires to specific brands, types,
or sizes.
WARNING: High pressure temporary compact spare tires should not be
used with any other rims or wheels, nor should standard
tires, snow tires, wheel covers, or trim rings be used
with high pressure compact spare rims or wheels.
Attempting to mount a tire of one diameter on a wheel of
a different diameter or flange type may result in serious
injury or death.
WARNING: Only specially trained persons should dismount or mount
tires. Explosions of tire and wheel assembly can result
from improper mounting, possibly causing serious injury
or death.
WARNING: Consult the vehicle owner's manual or vehicle placard for
correct size, speed rating, designation, and cold
inflation pressure of the original tires. DO NOT exceed
the maximum load or inflation capacity of the tire
specified by the Tire and Rim Association
WARNING: When replacing tires, it is suggested that the
replacement tires match or exceed the OEM speed rating
designation. If tires of different speed rating
designations are mixed on the same vehicle, the tires may
vary in handling characteristics. DO NOT mix different
speed rating designations on the same axle.
WARNING: DO NOT mix radials with non-radial tires on the same
axle, as this may affect vehicle handling and stability.
If radial tires and bias or bias-belted ply tires are
mixed on the same vehicle, the radials must be on the
rear. High-pressure temporary compact spare tires are
exempt from this rule.
WARNING: DO NOT mix size or type (all season, performance, mud and
snow) of tires on the same axle.
TIRE INSPECTION
\
\
\
\
\
\
\
Page 1179 of 1378
Loose ................... B ... Require repair or replacement
of affected component.
Lug nut installed
backward ............... B .. Require repair or replacement.
Lug nut mating type
incorrect .............. B ..... Require replacement of nut.
Lug nut mating surface
dished ................. A ..... Require replacement of nut.
Lug nut rounded ......... A . (2) Require replacement of nut.
Lug nut seized .......... A . ( 2) Require replacement of nut.
Stud incorrect .......... B .... Require replacement of stud.
Threads damaged ......... A ... Require repair or replacement
of component with damaged
threads.
Threads stripped ........ A .......... Require replacement of
component with stripped
threads.
( 1) - Some manufacturers require replacement of all studs on
that wheel if two or more studs or nuts on the same
wheel are broken or missing.
( 2) - Only required if removing wheel.
\
\
\
\
\
\
\
WHEELS (RIMS)
WARNING: Mounting a regular tire on a high-pressure compact spare
wheel is not permitted. Attempting to mount a tire of one
diameter on a wheel of a different diameter or flange
type may result in serious injury or death. If the wheel
identification stamp is not legible, or cannot be found,
do not use the wheel until the size and type have been
properly identified. Wheels of different diameter,
offset, or width cannot be mixed on the same axle. Bead
seat tapers cannot be interchanged.
WHEEL (RIM) INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Bead leaking, caused
by wheel ............... A ........... ( 1) Require repair or
replacement.
Bent hub mounting
surface ................ A ............ Require replacement.
Bent rim, causing
vibration .............. 2 ........ ( 1) Suggest replacement.
Broken .................. A ............ Require replacement.
Cast wheel porous,
causing a leak ......... A .. Require repair or replacement.
Clip-on balance weight is
incorrect type
for rim flange ......... 2 ............ Suggest replacement.
Corrosion, affecting
structural integrity ... A ............ Require replacement.
Corrosion build-up on
wheel mounting
surface ................ A ................. Require repair.
Cracked ................. A ............ Require replacement.
Directional/asymmetrical
wheels mounted
incorrectly ............ B ....... Require remounting and/or
repositioning.
Page 1222 of 1378
\003
TR O UBLE S H O OTIN G - B ASIC P R O CED URES
1988 J e ep C hero ke e
GENERAL TROUBLE SHOOTING
* PLEASE READ THIS FIRST *
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
ACCESSORIES & ELECTRICAL
CHARGING SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC CHARGING SYSTEM TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE CORRECTION \
\
\
\
\
\
\
Vehicle Will Not Dead battery Check battery cells,
Start alternator belt
tension and alternator
output
Loose or corroded battery Check all charging
connections system connections
Ignition circuit or switch Check and replace as
malfunction necessary
\
\
\
\
\
\
\
Alternator Light Loose or worn alternator Check alternator drive
Stays On With drive belt tension and
Engine Running condition, See Belt
Adjustment in TUNE-UP
article in the
TUNE-UP section
Loose alternator wiring Check all charging
connections system connections
Short in alternator light See Indicator Warning
wiring Lights in STANDARD
INSTRUMENTS in the
ACCESSORIES &
EQUIPMENT section
Defective alternator stator See Bench Tests in
or diodes ALTERNATOR article
Defective regulator See Regulator Check in
Page 1223 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual ALTERNATOR article \
\
\
\
\
\](/manual-img/16/57037/w960_57037-1222.png "JEEP CHEROKEE 1988 Service Repair Manual ALTERNATOR article \
\
\
\
\
\")
ALTERNATOR article \
\
\
\
\
\
\
Alternator Blown fuse See WIRING DIAGRAMS
Light Stays Off
With Ignition
Switch ON
Defective alternator See Testing in
ALTERNATOR article
Defective indicator light See Indicator Warning
bulb or socket Lights in STANDARD
INSTRUMENTS in the
ACCESSORIES &
EQUIPMENT section
\
\
\
\
\
\
\
Alternator Short in alternator wiring See On-Vehicle Tests
Light Stays OFF in ALTERNATOR article
With Ignition
Switch ON
Defective rectifier bridge See Bench Tests in
ALTERNATOR article
\
\
\
\
\
\
\
Lights or Fuses Defective alternator wiring See On-Vehicle Tests
Burn Out in ALTERNATOR article
Frequently
Defective regulator See Regulator Check in
ALTERNATOR article
Defective battery Check and replace as
necessary
\
\
\
\
\
\
\
Ammeter Gauge Loose or worn drive belt Check alternator drive
Shows Discharge belt tension and
condition. See Belt
Adjustment in TUNE-UP
article in the
TUNE-UP section
Defective wiring Check all wires and
wire connections
Defective alternator or See Bench Tests and
regulator On-Vehicle Tests in
ALTERNATOR article
Defective ammeter, or See Testing in
improper ammeter wiring STANDARD INSTRUMENTS
connection in the ACCESSORIES &
EQUIPMENT section
\
\
\
\
\
\
\
Noisy Loose drive pulley Tighten drive pulley
Alternator attaching nut
Loose mounting bolts Tighten all alternator
mounting bolts
Worn or dirty bearings See Bearing
Replacement
ALTERNATOR article
Page 1230 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual Fires With Key Flywheel runout contributes
released. Engine to the intermittent nature
Fires and Cranks
Normally
\
\
\
\](/manual-img/16/57037/w960_57037-1229.png "JEEP CHEROKEE 1988 Service Repair Manual Fires With Key Flywheel runout contributes
released. Engine to the intermittent nature
Fires and Cranks
Normally
\
\
\
\")
Fires With Key Flywheel runout contributes
released. Engine to the intermittent nature
Fires and Cranks
Normally
\
\
\
\
\
\
\
AIR CONDITIONING & HEAT
AIR CONDITIONING TROUBLE SHOOTING
WARNING: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC AIR CONDITIONING TROUBLE SHOOTING CHART
\
\
\
\
\
\
\
CONDITION POSSIBLE CAUSE \
\
\
\
\
\
\
Compressor Not Working
Compressor clutch circuit open.
Compressor clutch coil inoperative.
Poor clutch ground connection.
Fan belts loose.
Thermostatic switch inoperative.
Thermostatic switch not adjusted.
Ambient temperature switch open.
Superheat fuse blown. \
\
\
\
\
\
\
Excessive Noise or Vibration
Missing or loose mounting bolts.
Bad idler pulley bearings.
Fan belts not tightened correctly.
Compressor clutch contacting body.
Excessive system pressure.
Compressor oil level low.
Damaged clutch bearings.
Damaged reed valves.
Damaged compressor. \
\
\
\
\
\
\
Insufficient or No Cooling;
Compressor Working
Expansion valve inoperative.
Heater control valve stuck open.
Low system pressure.
Blocked condenser fins.
Blocked evaporator fins.
Vacuum system leak.
Vacuum motors inoperative.
Control cables improperly adjusted.
Restricted air inlet.
Mode doors binding.
Blower motor inoperative.
Temperature above system capacity. \
\
\
\
\
\
\
HEATER SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
Page 1307 of 1378
TU RN S IG NALS & H AZA R D F LA SH ER S
1988 J e ep C hero ke e
1988 Turn Signal & Hazard Light Systems
JEEP
DESCRIPTION
Turn signals and hazard flashers systems use a common turn
signal/hazard light switch assembly mounted within upper steering
column housing.
FLASHER LOCATIONS
Hazard
Mounted on fuse block.
Turn Signal
Mounted on fuse block.
TROUBLE SHOOTING
NOTE: Following trouble shooting is only information available
from manufacturer.
Hazard Lights (Comanche, Cherokee & Wagoneer)
If lights do not come on with hazard switch turned on, check
hazard/stop light fuse by operating stop lights. If fuse is okay,
check turn signal flasher, turn signal/hazard switch, and related
wiring. If only one hazard light does not work, check bulb.
Turn Signals (Comanche, Cherokee & Wagoneer)
If all turn signals do not work, check turn/back-up light
fuse by operating back-up lights. If fuse is okay, check turn signal
flasher, turn signal/hazard switch, and related wiring. If only one
turn signal does not work, check bulb.
TESTING
NOTE: Following trouble shooting is only information available
from manufacturer.
Hazard Indicators (Wrangler)
1) Turn ignition and hazard warning switch "ON". Check for
pulsating voltage at Light Blue (left indicator) and Dark Blue (right\
indicator) wires. If voltage is present, go to next step. If voltage
is not present, replace turn signal switch.
2) Remove bulbs for turn signal indicators. Measure
resistance across bulb terminals. If resistance is zero ohms, replace
light bulb(s). If resistance readings are not zero ohms, go to next
step.
3) Check for pulsating voltage at battery side of bulb
sockets. If voltage is present, go to next step. If voltage is not
present, repair open circuit between socket and turn signal switch
steering column connector.
4) Turn ignition off and check resistance on ground side of
bulb sockets. If resistance is zero ohms, hazard indicator circuit is
okay. If resistance reading is not zero ohms, repair open in ground
circuit.
Hazard Lights (Wrangler)
Page 1308 of 1378
1) Check operation of stop lights. If stop lights come on, go
to next step. If not, check hazard/stop light fuse. If fuse is okay,
check for voltage on battery side of hazard/stop light fuse. If
voltage is not present, repair open circuit between fusible link and
fuse block.
2) Remove hazard flasher and check for voltage on battery
side of hazard flasher at fuse block. If voltage is present, go to
next step. If voltage is not present, repair open circuit to fuse
block.
3) Measure resistance across turn signal flasher terminals.
If resistance across flasher is zero ohms, replace flasher. If
resistance is other than zero ohms, install flasher and turn ignition
on.
4) Check for voltage at Brown wire of turn signal switch
steering column connector. If voltage is present, go to next step. If
voltage is not present, repair open circuit between flasher and turn
signal switch connector.
5) Turn hazard warning switch "ON". Check for pulsating
voltage at Light Blue, Dark Blue, Yellow, and Dark Green wires. If
voltage is present, hazard light circuit is okay. If voltage is not
present, replace turn signal switch.
Turn Signals (Wrangler)
1) Turn ignition on and check operation of back-up lights. If
lights come on, go to step 3). If back-up lights do not come on, check
turn signal/back-up light fuse.
2) If fuse is okay, check for voltage at battery side of turn
signal/back-up light fuse. If voltage is not present, repair open
circuit between fuse block and ignition switch. If voltage is present,
go to next step.
3) Remove turn signal flasher and measure resistance across
flasher terminals. If resistance across flasher is zero ohms, replace
turn signal flasher. If flasher is okay, install flasher and turn
ignition on.
4) Check for voltage on battery side of flasher at fuse
block. If voltage is present, go to next step. If voltage is not
present, repair open circuit to fuse block.
5) Disconnect turn signal switch at steering column
connector. Place turn signal switch in left turn position and measure
resistance between Yellow and Purple wires. If resistance across wires
is zero ohms, replace turn signal switch. If resistance is other than
zero ohms, go to next step.
6) Place turn signal switch in right turn position and
measure resistance between Dark Green and Purple wires. If resistance
across wires is zero ohms, replace turn signal switch. If resistance
is other than zero ohms, turn signal circuit is okay.
Turn Signal Indicators (Wrangler)
1) Turn ignition on. Place turn signal switch in left turn
position and check for pulsating voltage at Light Blue wire. If
voltage is present, go to next step. If voltage is not present,
replace turn signal switch.
2) Place turn signal switch in right turn position and check
for pulsating voltage at Dark Blue wire. If voltage is not present,
replace turn signal switch. If voltage is present, go to next step.
3) Remove bulbs from turn signal indicators. Measure
resistance across bulb terminals. If resistance is zero ohms, replace
light bulb(s). If resistance readings are not zero ohms, turn ignition\
on.
4) Place turn signal switch in left and right turn position
and check for pulsating voltage at battery side of bulb sockets. If
voltage is present, go to next step. If voltage is not present, repair
open circuit between socket(s) and steering column connector.
Page 1369 of 1378
WIR IN G D IA G RAM S
1988 J e ep C hero ke e
1988 Wiring Diagrams
Jeep
Cherokee & Wagoneer
IDENTIFICATION
COMPONENT LOCATION MENU
COMPONENT LOCATIONS TABLE \
\
\
\
\
\
\
Component Figure No. (Location)
A/C & Htr Systems ............................... 5 (A-D 16-19)
Alternator ............................................ 1 (C 3)
Audio Alarm Module ................................... 7 (D 27)
Back-Up Lt Sw (M/T) .................................. 4 (D 12)
Battery ............................................... 1 (A 2)
Beam Sel Sw .......................................... 6 (E 23)
Brake Warning Sw ..................................... 6 (C 20)
Clock ................................................ 7 (E 27)
Clutch Switch ........................................ 4 (E 15)
Courtesy Lights ................................... 7 (C 24-26)
Cruise Ctrl Sys ................................... 4 (E 12-15)
Diag Conn D1 (2.5L) ................................... 3 (B 9)
Diag Conn D1 (4.0L) ................................... 2 (B 4)
Diag Conn D2 (2.5L) .................................. 3 (B 11)
Diag Conn D2 (4.0L) ................................... 2 (B 7)
DIR Hazard Sw ................................... 6 (D-E 20-21)
Door Switches ........................................ 7 (C 27)
Elect Ctrl Unit (2.5L) ............................. 3 (A 9-10)
Elect Ctrl Unit (4.0L) .............................. 2 (A 4-7)
Engine Compartment Lt ................................. 1 (C 1)
Fog Light Relay ....................................... 1 (D 2)
Fog Light Sw ...................................... 6 (E 21-22)
Fuel Pump Rly (2.5L) .................................. 3 (C 9)
Fuel Pump Rly (4.0L) ................................ 2 (E 5-6)
Fuel Tank Unit ....................................... 6 (B 20)
Fus Links ........................................... 1 (B 2-3)
Fuse Block ...................................... 4 (B-D 12-15)
4WD Switch ..................................... 6 (C 20, D 21)
Gear Sel Sw .......................................... 5 (C 16)
Glove Box Light ...................................... 7 (C 25)
Headlight Delay Module ............................... 6 (E 23)
Headlight Switch .................................. 6 (D 22-23)
Horn Relay ............................................ 1 (C 2)
Ignition Ctrl Mod (2.5L) ............................ 3 (B-C 8)
Ignition Ctrl Module (4.0L) ........................... 2 (E 4)
Ignition Key Warn Sw ................................. 7 (D 26)
Ignition Switch ................................... 4 (A 12-15)
Illum Lights .................................... 7 (C-D 24-25)
Instrument Cluster .............................. 6 (A-C 22-23)
Keyless Entry Module .............................. 7 (B 24-25)
Latch Rly (B+) (4.0L) ............................... 2 (B-C 4)
Power Antenna Rly .................................. 7 (D-E 27)
Power/Comfort Sw ..................................... 5 (D 19)
Power Door Lock Sys ............................. 7 (A-C 24-27)
Power Mirror Sw ................................. 7 (D-E 24-25)
Power Seat Sw ................................... 8 (A-B 28-29)