1988 JEEP CHEROKEE jump start

2.5L TBI
1) Adjustment of fuel pressure is required after replacement
of pressure regulator. Remove air inlet from throttle body. Connect
tachometer to diagnostic connector terminals D1-1 and D1-3. Connect
fuel pressure gauge to fuel body pressure test fitting.
NOTE: Some TBI models do not have a pressure test fitting on
throttle body. Use Fitting (PN 8983 501 572) for this
purpose.
2) Start engine and accelerate to 2000 RPM. Turn adjustment
screw to obtain 14.5 psi (1.02 kg/cm
) fuel pressure. Location of
adjustment screw is on bottom of regulator. Install lead seal ball to
cover regulator adjustment screw after adjusting fuel pressure to
specification. Turn ignition off. Disconnect fuel pressure gauge.
Install cap on test fitting. Install air inlet.
NOTE: To increase fuel pressure, turn adjustment screw inward. To
decrease fuel pressure, turn adjustment screw outward.
4.0L MPFI
1) Remove cap from pressure test port in fuel rail. Connect
Fuel Pressure Gauge (J-37730-1) to pressure fitting. Start vehicle.
Pressure should be approximately 31 psi (2.7 kg/cm
) with vacuum
hose connected to pressure regulator.
2) Pressure should be 39 psi (2.74 kg/cm
) with vacuum
hose removed from regulator. If fuel pressure is not to
specifications, check for kinks or restricting bends in fuel supply
and return lines. Check fuel pump flow rate. Pump should deliver
minimum of 1.06 quarts (one liter) of fuel per minute with fuel
return line pinched off.
3) If flow is inadequate, check system for plugged fuel
filter or filter sock. Fuel pump flow rate can be checked by
connecting a hose to fuel test port on fuel rail and inserting other
end in clean container.
4) To operate fuel pump, install a jumper wire into
diagnostic connector terminals D1-5 and D1-6. Pinch off fuel return
line to ensure that no fuel returns to fuel tank. If fuel pressure is
still not to specifications and fuel flow is normal, replace
regulator.
REMOVAL & INSTALLATION
FUEL PUMP
Removal (2.5L TBI)
1) Disconnect battery cables. Ensure fuel level is less than
1/2 for this procedure. Remove fuel outlet and return hoses. Remove
sending unit wires. Remove sending unit retaining lock ring.
2) Remove sending unit/pump assembly with "O" ring seal.
Disconnect fuel hose from fuel pump. Disconnect wires from fuel pump.
Remove fuel pump from sending unit.
Installation
Clean seal contact are of fuel tank. Install new "O" ring
seal. Install a new filter on end of suction tube. Position sending
unit/pump assembly in tank. To complete installation, reverse removal
procedure. Start engine and check for leaks.
CAUTION: Fuel leaks can develop from over tightening sending
unit/pump during installation.

reading of .2 volt or less. If reading exceeds .2 volt, clean or
repair cables and connections in circuit. Connect a voltmeter at
following locations:
* Positive lead to battery positive post and negative lead
to cable clamp.
* Positive lead to battery negative post and negative lead
to cable clamp.
3) If reading is other than zero on voltmeter, clean or
repair cables and connections in circuit. Connect a voltmeter at
following location:
* Positive lead to battery positive post and negative lead
to starter solenoid lead to the field coils.
4) If reading exceeds .3 volt, clean or repair cables and
connections in circuit.
SOLENOID TEST
1) Connect a heavy jumper wire on starter relay between
battery and solenoid terminals. If engine cranks, solenoid is okay. Go
to RELAY TEST .
2) If engine does not crank, check wiring and connections
from relay to starter. Repair or replace as necessary. If engine still
fails to crank, starter is defective.
RELAY TEST
1) On automatic transmission/transaxle vehicles, put gear
selector in "NEUTRAL" or "PARK". On manual transmission/transaxle
vehicles, put gear selector in "NEUTRAL". Set parking brake and block
wheels. DO NOT remove relay connector. Using a 12-volt test light,
check for battery voltage between starter relay battery terminal and
ground.
2) Use a jumper wire on starter relay between battery and
ignition terminals. If engine cranks starter relay is good. If starter
does not crank go to next step.
3) Connect another jumper wire to starter relay between
ground terminal and ground. Repeat above test. If engine cranks,
starter relay is good. Inspect transmission linkage for improper
adjustment (automatic transmission), defective neutral safety switch
(automatic transmission) or poor ground connection between relay
housing and mounting surface.
TESTING (ON BENCH)
STARTER SOLENOID
1) With starter removed, disconnect field coil wire from
field coil terminal on starter. Using an ohmmeter, check for
continuity between solenoid and field coil terminals.
2) Check for continuity between solenoid terminal solenoid
housing. Continuity should be present in both tests. If continuity is
present, solenoid is good. If no continuity is present, replace
solenoid. Reconnect field coil wire to field coil terminal.
ARMATURE FOR SHORT CIRCUIT
Place armature in a growler and hold a thin steel blade
parallel 3/16" above core while rotating armature slowly. If armature

SPARK PLUGS
SPARK PLUG TYPE TABLE








\









\









\









\









\









\






Application Champion No.
All Models ....................................... RFN14LY









\









\









\









\









\









\






SPARK PLUG SPECIFICATIONS TABLE








\









\









\









\









\









\






Gap: In. (mm) Torque: Ft. Lbs. (N.m)
0.035 (0.89) ................................ 7-15 (10-20)









\









\









\









\









\









\






FUEL PUMP
4.0L
1) Remove the cap from the pressure test port located in the
fuel rail. See Fig. 1. Connect Fuel Pressure Gauge (J-34730-1) to the
pressure fitting.
2) Start vehicle. Pressure should be approximately 31 psi (2.\
1 kg/cm
) with the vacuum hose connected to the pressure regulator and
39 psi (2.6 kg/cm) with the vacuum hose removed from the pressure
regulator. See FUEL PUMP SPECIFICATIONS TABLE .
3) Check the fuel pump flow rate. A good fuel pump will
deliver at least one liter of fuel per minute with the fuel return
line pinched off. If the fuel pump does not pump adequately, inspect
the fuel system for a plugged fuel filter or filter sock.
4) Fuel pump flow rate can be checked by connecting one end
of an old A/C gauge hose to the fuel test port on the fuel rail and
inserting the other end of the hose into a container of at least one
liter or more capacity.
5) Run the fuel pump by installing a jumper wire into
diagnostic connector terminals D1-5 and D1-6. Be sure to pinch off the
fuel return line or most of the fuel will be returned to the fuel
tank.
Fig. 1: Fuel System Pressure Test Components
Courtesy of American Motors/Jeep Corp.
4.2L
Perform fuel pump test with air cleaner removed and fuel

wires connected to switch). Disconnect distributor vacuum advance hose
and connect hose to vacuum switch. Disconnect wire connector from
knock sensor, located in cylinder head.
3) Using a jumper wire, ground knock sensor wire connector to
engine block. Start engine. With engine at idle speed (solenoid
energized), check timing. Adjust timing to one degree more than
specification (if required). See Emission Control Label.
IGNITION TIMING SPECIFICATIONS (DEGREES BTDC@RPM) - 4.2L









\









\









\









\









\









\






Application Man. Trans. Auto. Trans.
50 State ............. 9 @ 1600 ............... 9 @ 1600
High Altitude ........ 16 @ 1600 ............. 16 @ 1600









\









\









\









\









\









\






HOT (SLOW) IDLE RPM
4.0L
1) Apply parking brake and place transmission in Neutral
(Drive for automatic transmissions). Operate engine to normal
operating temperature. Turn ignition off.
2) Ensure all accessories are off. Connect positive
tachometer lead to terminal "D1-1" and negative lead to "D2-7" of
diagnostic connectors. See Fig. 3. Disconnect air stepper motor
connector and TPS wiring connector. See Fig. 4.
Fig. 3: Diagnostic Connector Terminal Identification
Courtesy of Chrysler Motors.